Sony STR-DA5800ES Service Manual ▷ View online
STR-DA5800ES
5
NOTE OF REPLACING THE IC1410 ON THE DCDC
BOARD
IC1410 on the DCDC board cannot exchange with single. When
this part is damaged, exchange the complete mounted board.
BOARD
IC1410 on the DCDC board cannot exchange with single. When
this part is damaged, exchange the complete mounted board.
NOTE OF REPLACING THE IC3903 AND IC3904 ON
THE DCDC2 BOARD
IC3903 and IC3904 on the DCDC2 board cannot exchange with
single. When these parts are damaged, exchange the complete
mounted board.
THE DCDC2 BOARD
IC3903 and IC3904 on the DCDC2 board cannot exchange with
single. When these parts are damaged, exchange the complete
mounted board.
NOTE OF REPLACING THE IC3500 AND IC3700 ON
THE D-VIDEO BOARD
IC3500 and IC3700 on the D-VIDEO board cannot exchange with
single. When these parts are damaged, exchange the complete
mounted board.
THE D-VIDEO BOARD
IC3500 and IC3700 on the D-VIDEO board cannot exchange with
single. When these parts are damaged, exchange the complete
mounted board.
NOTE OF REPLACING THE IC3505 AND IC3506 ON
THE D-VIDEO BOARD
Replacement of IC3505 and IC3506 on the D-VIDEO board used
in this unit requires a special tool.
THE D-VIDEO BOARD
Replacement of IC3505 and IC3506 on the D-VIDEO board used
in this unit requires a special tool.
NOTE OF REPLACING THE IC101, IC501 AND IC2601
ON THE NETWORK BOARD
IC101, IC501 and IC2601 on the NETWORK board cannot ex-
change with single. When these parts are damaged, exchange the
complete mounted board.
ON THE NETWORK BOARD
IC101, IC501 and IC2601 on the NETWORK board cannot ex-
change with single. When these parts are damaged, exchange the
complete mounted board.
NOTE OF REPLACING THE IC106, IC107, IC206 AND
IC207 ON THE NETWORK BOARD
Replacement of IC106, IC107, IC206 and IC207 on the NET-
WORK board used in this unit requires a special tool.
IC207 ON THE NETWORK BOARD
Replacement of IC106, IC107, IC206 and IC207 on the NET-
WORK board used in this unit requires a special tool.
NOTE OF REPLACING THE IC101 AND IC102 ON
THE USB-DDC BOARD (AEP, UK and Taiwan models
only)
IC101 and IC102 on the USB-DDC board cannot exchange with
single. When these parts are damaged, exchange the complete
mounted board.
THE USB-DDC BOARD (AEP, UK and Taiwan models
only)
IC101 and IC102 on the USB-DDC board cannot exchange with
single. When these parts are damaged, exchange the complete
mounted board.
NOTE OF REPLACING THE IC100 ON THE USB-DDC
BOARD (AEP, UK and Taiwan models only)
Replacement of IC100 on the USB-DDC board used in this unit
requires a special tool.
BOARD (AEP, UK and Taiwan models only)
Replacement of IC100 on the USB-DDC board used in this unit
requires a special tool.
MODEL IDENTIFICATION
Distinguish the model by part number on back panel.
Distinguish the model by part number on back panel.
– Back Panel –
US and Canadian models:
4-422-950-0s
4-422-950-0s
AEP and UK models:
4-422-950-1s
Taiwan model:
4-422-950-3s
4-422-950-1s
Taiwan model:
4-422-950-3s
CAPACITOR ELECTRICAL DISCHARGE PROCESSING
When checking the board, for the electric shock prevention, con-
nect the resistors to both ends of respective capacitors (C905 on
the ACDC board) to discharge the capacitors (C905 on the ACDC
board).
When checking the board, for the electric shock prevention, con-
nect the resistors to both ends of respective capacitors (C905 on
the ACDC board) to discharge the capacitors (C905 on the ACDC
board).
– ACDC Board (Conductor Side) –
C905
800
:/2 W
ADVANCE PREPARATION OF REPAIR
(US and Canadian models only)
This unit in US and Canadian models can perform “PRO-UP-
GRADE” by C4 (Control4) dealer.
When the user is performing “PRO-UPGRADE”, GUI of C4
(Control4) world is displayed.
Display GUI in the following procedure and confi rm the state of
displayed GUI.
(US and Canadian models only)
This unit in US and Canadian models can perform “PRO-UP-
GRADE” by C4 (Control4) dealer.
When the user is performing “PRO-UPGRADE”, GUI of C4
(Control4) world is displayed.
Display GUI in the following procedure and confi rm the state of
displayed GUI.
Connection:
STR-
DA5800ES
monitor
D-VIDEO board
HDMI OUT A ARC connector
(CN3502)
HDMI OUT A ARC connector
(CN3502)
HDMI cable
Procedure:
1. Press the [
1. Press the [
?/1
] button to turn on the main power.
2. Press the [HDMI OUT A/B/OFF] button to select “HDMI A”.
3. Press the [HOME] button of remote commander.
4. “PRO-UPGRADE” is not performed when the following
3. Press the [HOME] button of remote commander.
4. “PRO-UPGRADE” is not performed when the following
screen is displayed.
Note: If the following processing is performed to this unit by which
“PRO-UPGRADE” was performed, this unit returns to the state
before “PRO-UPGRADE” is performed.
before “PRO-UPGRADE” is performed.
•
Complete NETWORK board replacing
•
Factory
reset
Since the change to C4 (Control4) world can perform only by
C4 (Control4) dealer, fully work carefully.
C4 (Control4) dealer, fully work carefully.
Ver. 1.2
STR-DA5800ES
6
CONFIRMATION OF NETWORK OPERATION
Note: When this confi rmation is executed, IP address is changed.
Necessary machinery and materials:
•
•
PC (Windows XP/Vista)
• Router
(Transmission rate is 100 Mbps or more, built-in DHCP server
function)
function)
•
Two LAN cables
(Category 5 cable, normal type or shield type)
• Monitor
•
•
Supplied remote commander (RM-AAU154)
(US and Canadian models)
•
Supplied multifunction remote commander (RM-AAL042)
(AEP, UK and Taiwan models)
Connection:
(The router need not be connected with the internet)
(The router need not be connected with the internet)
LAN cable
router
PC
STR-
DA5800ES
monitor
NETWORK board
jack (CN2502)
D-VIDEO board
HDMI OUT A ARC connector
(CN3502)
HDMI OUT A ARC connector
(CN3502)
HDMI cable
Procedure:
1. The setting of LAN of PC is setting to the automatic IP address
1. The setting of LAN of PC is setting to the automatic IP address
assignment.
It changes to the setting that displays the image in the monitor.
2. Perform connection with reference to connection fi gure.
3. The power supply of the router is turn on, next, the power sup-
3. The power supply of the router is turn on, next, the power sup-
ply of PC and this unit is turn on.
4. Press the [HOME] button of the remote commander, the home
menu is displayed in the monitor.
5. The “Settings” is selected on the home menu, and press the [
]
button of remote commander.
6. The “Network Settings” is selected , and press the [
] button
of remote commander.
7. The “Internet Settings” is selected , and press the [
] button of
remote commander.
8. The “Network Setup” is selected , and press the [
] button of
remote commander.
9. The “Auto” is selected , and press the [
] button of remote
commander.
10. The “The network will be confi gured with the following set-
tings.” is displayed, and press the [
,
] button of remote com-
mander.
11. The “Save & Connect” is selected , and press the [
] button of
remote commander.
12. The automatically connect function is performed.
13. Confi rm that the “Internet Access: OK” has been displayed,
13. Confi rm that the “Internet Access: OK” has been displayed,
and press the [
] button of remote commander.
14. Press the [\/1] button to turn off the main power.
NOTE OF REPLACING THE COMPLETE NETWORK
BOARD
When the complete NETWORK board is exchanged, the MAC ad-
dress has been changed.
Please print and cut out the following explanations, and return it
with the unit that completes the repair.
BOARD
When the complete NETWORK board is exchanged, the MAC ad-
dress has been changed.
Please print and cut out the following explanations, and return it
with the unit that completes the repair.
MAC address of this receiver has been changed by this repair.
The customer who uses the MAC address fi ltering function of
connected access point equipment please set it again. MAC ad-
dress is possible to confi rm it on the System Information screen
of this unit. Please refer to “Adjusting Settings” on the operating
instructions for details.
The customer who uses the MAC address fi ltering function of
connected access point equipment please set it again. MAC ad-
dress is possible to confi rm it on the System Information screen
of this unit. Please refer to “Adjusting Settings” on the operating
instructions for details.
NOTE OF REPLACING THE COMPLETE USB-DDC
BOARD (AEP, UK and Taiwan models only)
When this unit is connected with PC, this unit is recognized as a
USB audio device on PC. At this time, the manufacture maker’s
information, etc. (USB descriptor) are transmitted to PC from this
unit. The USB descriptor is stored in the IC102 on the USB-DDC
board, and it is written in at the factory.
When the complete USB-DDC board is exchanged, do the follow-
ing work.
BOARD (AEP, UK and Taiwan models only)
When this unit is connected with PC, this unit is recognized as a
USB audio device on PC. At this time, the manufacture maker’s
information, etc. (USB descriptor) are transmitted to PC from this
unit. The USB descriptor is stored in the IC102 on the USB-DDC
board, and it is written in at the factory.
When the complete USB-DDC board is exchanged, do the follow-
ing work.
1. Preparation
Prepare the following before beginning work.
Prepare the following before beginning work.
•
Windows PC (Windows XP)
Note 1: Vendor does not guarantee operation by other OS’s.
•
Driver software for STR-DA5800ES
Note 2: Install this driver software in the above PC in advance. Confi rm
the method of obtaining the driver software to each service head-
quarters.
•
USB cable (A type plug to B type plug)
•
Writing utility software (.exe fi le)
•
USB descriptor defi nition fi le (.hex fi le)
Note 3: Confi rm the method of obtaining the writing utility software and
USB descriptor defi nition fi le to each service headquarters.
2. Writing
method
Procedure:
1. Assemble new USB-DDC board to this unit.
2. Connect PC and this set with USB cable.
1. Assemble new USB-DDC board to this unit.
2. Connect PC and this set with USB cable.
PC
USB cable
This unit
(rear side view)
(rear side view)
3. Press the [\/1] button on this unit to turn on the main power.
(It is not necessary to wait for memory clearing)
4. Run
the
writing utility software on PC.
5. Select the “USB\Vid_0d8c&Pid_5200&Rev_0100” on “De-
vice menu” pull-down list of the writing utility software.
USB/Vid_0d8c&Pid_5200&Rev_0100
Ver. 1.2
STR-DA5800ES
7
6. Click the “Update FW” button of the writing utility software
on PC and open the USB descriptor defi nition fi le.
USB/Vid_0d8c&Pid_5200&Rev_0100
Update FW
Update Firmware
Release_0605
6631-XXXX-SonySTR-ALL.hex
Firmware File
6631-XXXX-SonySTR-ALL.hex
Open
7. “Update Firmware” window appears, and click the “OK” but-
ton.
Cancel
OK
Start To Update Firmware.
Old Version: New Version:XXXX
Old Version: New Version:XXXX
8. After “Update Firmware” window disappears, wait for about 5
to 10 seconds.
9. After about 5 to 10 seconds, “FWUpdate” window appears,
and click the “OK” button.
OK
Firmware Update Finished
Device will be reset.
10. The writing of the USB descriptor to the IC102 on the USB-
DDC board is completed.
3. Checking
method
Procedure:
1. Open the Device Manager of windows on PC.
2. Expand the “Sound, video and game controllers”, and right-
1. Open the Device Manager of windows on PC.
2. Expand the “Sound, video and game controllers”, and right-
click on the “AV Amplifi er/Receiver” and select the “Proper-
ties”.
ties”.
SSF0250
AV Amplifier/Receiver
Properties
Update Driver...
Scan for hardware changes
3. Click the “Details” tab, and select the “Hardware Ids” from pull-
down list on Property. Check that the part surrounded by the
dotted line of the following fi gure is “VID_054C&PID_06CF”.
dotted line of the following fi gure is “VID_054C&PID_06CF”.
Property
Value
Hardware Ids
USB\VID_054C&PID_06CF&REV_0103&MI_00
USB\VID_054C&PID_06CF&MI_00
USB\VID_054C&PID_06CF&MI_00
Audio Amplifier/Receiver
4. The checking was completed.
XXXX: Version display
XXXX: Version display
STR-DA5800ES
8
Jig No.
Jig Name
Part No.
Pitch (mm)
Cores
Remark
1
2.00_20_M
J-2501-372-A
2.0
10
For E-VOL board (CN1201)
2.00_20_M
For A-CLASS_AMP board (CN1504)
PH cable 10P
Length 400 mm
2
2.00_20_M
J-2501-373-A
2.0
19
For E-VOL board (CN1202)
2.00_20_M
For A-CLASS_AMP board (CN1505)
PH cable 10P
Length 400 mm
PH cable 10P
Length 400 mm
3
2.00_15_M
J-2501-366-A
2.0
15
For E-VOL board (CN1203)
2.00_15_M
For MAIN board (CN1203)
PH cable 15P
Length 400 mm
4
2.00_20_M
J-2501-367-A
2.0
20
For E-VOL board (CN1204)
2.00_20_M
For MAIN board (CN1204)
PH cable 10P
Length 400 mm
PH cable 10P
Length 400 mm
E-VOL BOARD SERVICE POSITION
•
•
Please connect following extension jig.
– Rear side view –
A-CLASS_AMP board
(CN1504)
(CN1504)
Connect extension jig 2 to the
A-CLASS_AMP board (CN1505)
and E-VOL board (CN1202).
A-CLASS_AMP board (CN1505)
and E-VOL board (CN1202).
Connect extension jig 3 to the
MAIN board (CN1203)
and E-VOL board (CN1203).
MAIN board (CN1203)
and E-VOL board (CN1203).
E-VOL board
(CN1202)
(CN1202)
A-CLASS_AMP board
(CN1505)
(CN1505)
Connect extension jig 1 to the
A-CLASS_AMP board (CN1504)
and E-VOL board (CN1201).
A-CLASS_AMP board (CN1504)
and E-VOL board (CN1201).
Connect extension jig 4 to the
MAIN board (CN1204)
and E-VOL board (CN1204).
MAIN board (CN1204)
and E-VOL board (CN1204).
E-VOL board
(CN1201)
(CN1201)
E-VOL board
(CN1203)
(CN1203)
E-VOL board
(CN1204)
(CN1204)
MAIN board
(CN1203)
(CN1203)
MAIN board
(CN1204)
(CN1204)
alligator clip
Note: Connect altogether the metal part
Note: Connect altogether the metal part
on the boards connected with the
chassis using the alligator clip.
insulating sheet
Click on the first or last page to see other STR-DA5800ES service manuals if exist.