DOWNLOAD Sony STR-DA5800ES Service Manual ↓ Size: 25.81 MB | Pages: 127 in PDF or view online for FREE

Network update check

LINE CHECK FOR UPD

When [

,] button on the remote commander is pressed, the 

message “START ?” is appears. If the [

] button of the remote 

commander is pressed, check is started. The signal path for 
update is checked without connecting to network.
When all the checking results are OK, this unit is rebooted 
about 2 minutes after.
When the checking results are NG, the NG factors are dis-
played.

Result is displayed on the fl uorescent indicator tube. 

NG : MSVfDd

NG : DdVf

NG : Dd

NG : Vf

NG : V

NG : f

detail:
  M : Main system controller
  S  : Sub system controller
  V  : Video system controller
  f  : Video processor 
  D : DSP flash 1st
  d  : DSP flash 2nd

Result is displayed by lighting of the [ON/STANDBY] LED.

gray color part = [ON/STANDBY] indicator is on.

When the main system controller is NG

0

1

2

3

4

5

6

7

8

9

10

When the sub system controller is NG

0

1

2

3

4

5

6

7

8

9

When the main system controller and sub system controoler 
are NG

0

1

2

3

4

5

6

7

8

9

10 11 12 13 (sec)

Network audio/video test mode on/off

NWC DIAG XXX

Not used for the servicing.

Network completion time-out on/off 
setting

NET-OFF TIMEOUT XXX

Not used for the servicing.

Network PIP video on/off

PIP TEST XXX

Not used for the servicing.

HDCP key read

HDCP KEY READ XXX

Not used for the servicing.

DDR2 check

DDR2 CHECK XXXX

Not used for the servicing.

Model/destination change

MODEL A58ES XXX at

Not used for the servicing.

Video factory menu

<VIDEO FACTORY MENU>

Menu mode to enter video calibration menu and DDR access 
check menu.
If the [

,] button of the remote commander is pressed, en-

tering the menu, and operating the following menu become 
possible.

Video calibration mode
(Video factory menu)

V.CALIBRATION START?

Refer to “VIDEO CALIBRATION ADJUSTMENT” (page 56) for 
the details.

Video path check
(Video factory menu)

V PATH XXX: XXX

Not used for the servicing.

Auto cal mic test

SPEAKER OUT XXXXX

XXXXX: Output setting from the speaker
SOURCE: normal mode
MIC: mode that output audio to the speaker from microphone 
input

ARC check

ARC CHECK XXX

XXX: “ON” or “OFF”
SPDIF signal reception on/off switched.

FL display fonts test

FL FONT 0x**=X

**: 20 to FE, X: character

FL display test

(All segments turn on)

Each time [DISPLAY MODE] button to change as follows all on 
t test pattern 1 t test pattern 2 t all off t all on

Super reset

SUPER RESET XXX

Not used for the servicing
If super reset is performed, “VIDEO CALIBRATION ADJUST-
MENT” will also be initialized
When EEPROM initialization is required, perform the “SHIP-
MENT MODE” (page 50)

RAM watch menu

RAM WATCH MENU

Not used for the servicing.

EERROM debug mode

EEPROM **** XX

Not used for the servicing.

EERROM check

EEPROM CHECK

Not used for the servicing.

GUI boot check

GUI CHECK XXX

Not used for the servicing.

World switching

CONTROL4 GUI XXX

Not used for the servicing.

Watch dog on/off setting

WATCH DOG XXX

Not used for the servicing.

DAC reset function

DAC RESET

Not used for the servicing.

Sleep time shortening on/off 
setting

SLEEP DEBUG XXX

Not used for the servicing.

Auto standby

AUTO STBY DEBUG XXX

The message “ON” or “OFF” is appears.
Auto standby function on/off switched (setting value is 2 min-
utes)

Auto standby signal level

SIGNAL LVL XXXXXXXX

XXXXXXXX: Current signal level

Auto standby signal min

SIGNAL MIN XXXXXXXX

XXXXXXXX: Minimum signal level
Each time [MEMORY/ENTER] button is pressed, value is 
reset.

Auto standby signal max

SIGNAL MAX XXXXXXXX

XXXXXXXX: Maximum signal level
Each time [MEMORY/ENTER] button is pressed, value is 
reset.

Protector on/off setting

PROTECTR ON/OFF XXX

Not used for the servicing.

Audio swap mode

SWAP-AT XX.XX -> XX.XX

Not used for the servicing.

Volume value display (FL/FR)

FL

 FR XXXX

Not used for the servicing.

Volume value display (SL/SR)

SL

 SR XXXX

Not used for the servicing.

Volume value display (CT/SW)

CT

 SW XXXX

Not used for the servicing.

Volume value display (SBL/SBR)

SBL

 SBR XXXX

Not used for the servicing.

DAC mute fl ag upper

DAC MUTE U XXXXXXXX

Not used for the servicing.

DAC mute fl ag lower

DAC MUTE L XXXXXXXX

Not used for the servicing.

2nd volume value display

2nd VOLUME XXX.X dB

Not used for the servicing.

Dark out duty

DARK OUT DUTY XX%

Not used for the servicing.

H. A. T. S. playback component check

CHK HATS COMP XXX

Not used for the servicing.

H. A. T. S. mode fi x

HATS FIX XXXXXXX

Not used for the servicing.

H. A. T. S. rate control

HATS RATE XXXXXX

Not used for the servicing.

H. A. T. S. error process check

HATS ERR PROC XXX

Not used for the servicing.

H. A. T. S. error trigger

HATS ERR TRIG

Not used for the servicing.

Pass through auto debug

PASS THRU AUTO DBG

Not used for the servicing.

Note: After 10 minutes or more have passed since the power supply was turned on, this adjustment is done.

CN1561 (CN1611, CN1761, CN1861, CN4441, CN4491) pin 1, CN1561 (CN1761, CN1861) pin 3
CN1561 (CN1611, CN1761, CN1861, CN4441, CN4491) pin 2, CN1561 (CN1761, CN1861) pin 4

Note: Pin 3, 4 of CN1611, CN4441, CN4491 are open.

Procedure:
1.  Connect a digital voltmeter to the CN1561 (CN1611, CN1761, CN1861, CN4441, CN4491).
2. Press 

the 

[\/1] button to turn on the main power.

3.  Adjust the RV1501 (RV1551, RV1601, RV1701, RV1751, RV1801, RV1851, RV4421, RV4471) so that the digital voltmeter reading is 

5 mV to 20 mV. 

Note: Adjust for the digital voltmeter reading to become 5 mV as much as possible.

VIDEO  CALIBRATION  ADJUSTMENT
Adjustment to decide the standard of the video input signal.

Note: After replacing A-VIDEO board, perform this adjustment.

The color pattern generator that can output 100% in NTSC/PAL/
HD color bar signal to the component and the composite at the 
same time is necessary for the adjustment.
When there is no color pattern generator, it is possible to substitute 
it by the Blu-ray Disc player that can output the component termi-
nal and the video terminal at the same time (Substitution model 
name example: BDP-S350).
However, please do the following signal output confi rmation with 
the oscilloscope beforehand when substituting it with the Blu-ray 
Disc player.

1-1. Component signal
Checking Component Video Output Y

Signal

DVD standard disc color bars (100%)

Check point

COMPONENT VIDEO OUT (Y)
terminal (75 

 terminated)

Specifi cation

1.00 ± 0.03 Vp-p

r 0.03 Vp-p

Checking Component Video Output B-Y

Signal

DVD standard disc color bars (100%)

Check point

COMPONENT VIDEO OUT (P

B

/C

B

)

terminal (75 

 terminated)

Specifi cation

0.70 ± 0.03 Vp-p

r 0.03 Vp-p

Checking Component Video Output R-Y

Signal

DVD standard disc color bars (100%)

Check point

COMPONENT VIDEO OUT (P

R

/C

R

)

terminal (75 

 terminated)

Specifi cation

0.70 ± 0.03 Vp-p

r 0.03 Vp-p 

1-2. Composite signal
Video level confi rmation

Signal

DVD standard disc color bars (100%)

Check point

LINE OUT (VIDEO) terminal
(75 

 terminated)

Specifi cation

1.00 ± 0.03 Vp-p

r 0.03 Vp-p

• Preparation
Procedure:
1.  Press the [

?/1

] button to turn on the main power.

2.  Press the [HOME] button on the remote commander, and 

home menu is displayed on the TV monitor.

3.  Select the “Settings”, and press the [

] button on the remote 

commander.

4.  Select the “Zone Settings”, and press the [

] button on the 

remote commander.

5.  Select the “Zone Control”, and press the [

] button on the 

remote commander.

6.  Select zone 2, and press the [

] button on the remote com-

mander.

7.  Select the “On”, and press the [

] button on the remote com-

mander.

8.  Press the [HOME] button on the remote commander, and 

home menu is displayed on the TV monitor.

9.  Select the “Settings”, and press the [

] button on the remote 

commander.

10. Select the “Zone Settings”, and press the [

] button on the 

remote commander.

11. Select the “Zone Control”, and press the [

] button on the 

remote commander.

12. Select zone 2, and press the [

] button on the remote com-

mander.

13. Select the “Input”, and press the [

] button on the remote 

commander.

14. Select the “DVD”, and press the [

] button on the remote 

commander.

15. Press the [HOME] button on the remote commander, and 

home menu is displayed on the TV monitor.

16. Select the “Settings”, and press the [

] button on the remote 

commander.

17. Select the “Video Settings”, and press the [

] button on the 

remote commander.

18. Select the “Zone Resolution”, and press the [

] button on the 

remote commander.

19. Select the “720P”, and press the [

] button on the remote 

commander.