DOWNLOAD Sony STR-DA5800ES Service Manual ↓ Size: 25.81 MB | Pages: 127 in PDF or view online for FREE

MEMORY  CLEAR  MODE
All preset contents are cleared when this mode is activated.
(Sound fi eld is also cleared)
Use this mode before returning the product to clients upon comple-
tion of repair.
Procedure:
1.  While pressing the [TONE] and [2CH/A.DIRECT] buttons, 

press the [

?/1

] button to turn on the main power.

2.  The message “MEMORY CLEARING...” appears and the 

memories are reset to the default values.

 

(This operation takes about 2 minutes)

MEMORY CLEARING...

3.  When done, the message “MEMORY CLEARED !” appears.

MEMORY CLEARED !

FACTORY  PRESET  MODE
The specifi c preset values are set.
Procedure:
1.  While pressing the [TUNING] and [2CH/A.DIRECT] buttons, 

press the [

?/1

] button to turn on the main power.

2.  The message “Factory Preset” appears and specifi c preset val-

ues are set.

Factory Preset

TUNER  AM  STEP  CHANGE  MODE 
(US and Canadian models)
Either the 9 kHz step or 10 kHz step can be selected for the AM 
channel step.
Procedure:
1.  Press the [

?/1

] button to turn off the main power.

2.  While pressing the [TUNING] button, press the  [

?/1

] button 

to turn on the main power.

3.  Either the message “AM 9k Step” or “AM10k Step” appears, 

select the desired step.

AM 9k Step

AM10k Step

SOUND  FIELD  CLEAR  MODE
The preset sound fi eld is cleared when this mode is activated.
Use this mode before returning the product to clients upon comple-
tion of repair.
(When MEMORY CLEAR MODE or SHIPMENT MODE is per-
formed, it is not necessary to perform the SOUND FIELD CLEAR 
MODE)
Procedure:
1.  While pressing the [MUSIC] button, press the [

?/1

] button to 

turn on the main power.

2.  The message “S.F. Initialize” appears and initialization is per-

formed.

S.F.Initialize

FLUORESCENT  INDICATOR  TUBE  DISPLAY  TEST
All fl uorescent segments are tested. When this test is activated, all 
segments turn on at the same time, then each segment turns on one 
after another.
Procedure:
1.  While pressing the [TONE] and [A.F.D.] buttons, press the 

[

?/1

] button to turn on the main power.

2.  All segments and all LEDs turn on.

3.  Each time the [DISPLAY MODE] button is pressed, the screen 

display is changed in order as follows.

Releasing method:
Press the [

?/1

] button to turn off the main power.

SWAP  MODE
The signal will be swap to all channel so that all speaker will have 
sound output.
Procedure:
1.  While pressing the [MEMORY/ENTER] and [2CH/A. DI-

RECT] buttons, press the [

?/1

] button to turn on the main 

power.

2.  The message “SWAP MODE !” appears (No change while dis-

played).

SWAP MODE !

Releasing method:
Pull out the power cord.

SETTING  LOCK  ON/OFF  CHANGE  MODE
All the settings can be locked.
Procedure:
1.  While pressing the [SPEAKERS A/B/A+B/OFF] and [MU-

SIC] buttons, press the [

?/1

] button to turn on the main power.

2.  The message “SETTINGS LOCK [ ON]” appears.

SETTINGS LOCK [ ON]

Releasing method:
1.  While pressing the [SPEAKERS A/B/A+B/OFF] and [MU-

SIC] buttons, press the [

?/1

] button to turn on the main power.

2.  The message “SETTINGS LOCK [OFF]” appears.

SETTINGS LOCK [OFF]

COMMAND  MODE  CHANGE  MODE
The command mode of the remote-commander which this set re-
ceives can be changed.
Procedure:
1.  While pressing the [2CH/A. DIRECT] button, press the [

?/1

] 

button to turn on the main power.

2.  Either the message “COMMAND MODE [AV1]” or “COM-

MAND MODE [AV2]” appears. Select the desired mode.

COMMAND MODE [AV1]

COMMAND MODE [AV2]

SOFTWARE  VERSION  DISPLAY  MODE
The software version is displayed.

Note: In this mode, never press the [

M] and [m] buttons on the remote 

commander.

Procedure:
1.  While pressing the [TONE] and [MUSIC] buttons, press the 

[

?/1

] button to turn on the main power.

2.  The model name/destination/system controller software ver-

sion appears. Each time the [DISPLAY MODE] button is 
pressed, the version is switched in order as follows.

 

(Displayed characters/values in the following fi gure are ex-
ample)

MAIN A58ES UCA v1.00

SUB COMMON C v1.00

NET Ver   D1000

SYSTEM VERSION 1.000

VIDEO Ucom Ver 1.00

FAROUDJA2nd Ver 1.00

DSP SFLASH1 Ver 1.00

DSP SFLASH2 Ver 1.00

Releasing method:
Press the [

?/1

] button to turn off the main power.

SHIPMENT  MODE
Initialize backup of EEPROM and Network and return to state of 
the shipment.
Procedure:
1.  While pressing the [TONE] and [MOVIE/HD-D.C.S.] buttons, 

press the [

?/1

] button to turn on the main power.

2.  The message “MEMORY CLEARING...” appears and return 

to state of the shipment.

 

(This operation takes about 2 minutes)

MEMORY CLEARING...

3.  When done, the message “STANDBY” appears and turn off 

the main power.

STANDBY

REBOX  TEST  MODE
Displayed the number of times of the power on after the shipment.
Procedure:
1.  While pressing the [A.F.D.] and [SPEAKERS A/B/A+B/OFF] 

buttons, press the [

?/1

] button to turn on the main power.

2.  The number of times of the power on after the shipment ap-

pears.

 

(Displayed values in the following fi gure are example)

REBOX-  02

Releasing method:
Press the [

?/1

] button to turn off the main power.

KEY  CHECK  MODE
Each buttons can be checked.
Procedure:
1.  While pressing the [MEMORY/ENTER] and the [MOVIE/

HD-D.C.S.] buttons, press the [

?/1

] button to turn on the main 

power.

2.  Either the message “REST 17” appears.
 

Every pressing of any button other than the [

?/1

] counts down 

the buttons.

 

(The buttons which are already counted once are not counted 
again)

REST 17

3.  When all buttons are pressed “REST 00” appears.

REST 00

Releasing method:
Pull out the power cord, or do not perform operation for 10 sec-
onds.

HISTORY  MODE
The state that the set is used is memorized.

Note: Even if “MEMORY CLEAR MODE” is performed, the backup data 

of “HISTORY MODE” is not cleared.

 

  Initialize by performing “SHIPMENT MODE”.

Procedure:
1.  While pressing the [MEMORY/ENTER] and [MUSIC] but-

tons, press the [

?/1

] button to turn on the power and “HIS-

TORY” is displayed.

HISTORY MODE

2.  Each time the [

M] or [m] buttons of remote commander is 

pressed, the item is switched in order as follows.

 

(Displayed characters/values in the following fi gure are ex-
ample)

PRCT_COUNT:

TTL_TIME:      H M

TTL_MAIN:      H M

PROTECT:

SF

INPUT:

INMODE:

DSEL:

STREAM:

CONFIG:

HEADPHONE:

VOL:         .  dB

MUTING:

FRT BASS:    .  dB

FRT TREB:    .  dB

CNT BASS:    .  dB

CNT TREB:    .  dB

SUR BASS:    .  dB

SUR TREB:    .  dB

FH  BASS:    .  dB

FH  TREB:    .  dB

Lv FL/FR:  . /  .

Lv CT/SW:  . /  .

TTL_P_ON:     H10M

TTL_M_ON:     H10M

REBOX: 06

Lv SL/SR:  . /  .

Lv BL/BR:  . /  .

Lv LH/RH:  . /  .

Releasing method:
Press the [

?/1

] button to turn off the main power.

SPECIAL  MENU  MODE
Various version displays of system, update, test, etc. can be performed.
Setting method:
1.  Press the [

?/1

] button to turn on the main power.

2.  While pressing the [TONE] button, press the [A.F.D.], [2CH/A. DIRECT], [MUSIC], [MOVIE/HD-D.C.S.] button in order, the mes-

sage “MENU SPECIALIZED !” appears.

3.  Press the [AMP MENU] button of the remote commander, the message “<<< SPECIAL >>>” appears.
4.  Press the [

,

] button of the remote commander, the item is appears.

5.  Each time the [

M

] or [

m

] buttons of the remote commander is pressed, the item is switched in order of “Display of special menu mode”.

 

Some items can change the content. Display the cursor by pressing the [

,

] button of the remote commander, and changing the content 

by pressing the [

M

] or [

m

] buttons of the remote commander, and fi x the content by pressing the [

<

] button of the remote commander 

when you want to change the content of the item.

Releasing method:
To release from this mode, while pressing the [TONE] button, press the [A.F.D.], [2CH/A. DIRECT], [MUSIC], [MOVIE/HD-D.C.S.] but-
ton in order again, the message “MENU SPECIALIZE OFF” appears, and this mode is released.

SYSTEM version display

SYSTEM VERSION X.XXX

X.XXX: System software version

MAIN Ucom version display

MAIN A58ES *** vX. XX

***: Destination
X.XX: Main system controller software version

SUB Ucom version display

SUB COMMON C vX.XX

X.XX: Sub system controller software version

VIDEO Ucom version display

VIDEO Ucom Ver X. XX

X.XX: Video system controller software version (main)

FAROUDJA (2nd) version display

FAROUDJA2nd Ver X. XX

X.XX: Video processor software version (2nd)

DSP serial fl ash1 version display

DSP SFLASH1 Ver X. XX

X.XX: DSP serial fl ash1 software version

DSP serial fl ash2 version display

DSP SFLASH2 Ver X. XX

X.XX: DSP serial fl ash2 software version

Network processor version display

NET Ver DXXXX

XXXX: Network processor fi rmware version

IR learning Ucom version display

IR Ver XX.XX.XX

XX.XX.XX: IR controller software version

DSP debug menu

< DSP DEBUG MENU >

Not used for the servicing.

DSP serial fl ash1 data check

DSP SFLASH1 ID XX

XX: OK or NG

DSP serial fl ash2 data check

DSP SFLASH2 ID XX

XX: OK or NG

Network debug menu

<NETWORK DEBUG MENU>

Menu mode to enter MAC address display. If the [

,] button 

of the remote commander is pressed, entering the menu, and 
operating the following menu become possible.

MAC address display 
(Network debug menu)

MACXX:XX:XX:XX:XX:XX

XX:XX:XX:XX:XX:XX: MAC address

External control on/off
(Network debug menu)

EXTERNAL CTRL XXX

Not used for the servicing.

Network standby on/off
(Network debug menu)

NETWORK STANDBY XXX

Not used for the servicing.

Network audio signal path switch
(Network debug menu)

AUDIO ROUTE XXXX

Not used for the servicing.

DAC error signal invalidity
(Network debug menu)

IGNORE DA-ERR XXX

Not used for the servicing.

Network compulsive party mode
(Network debug menu)

FORCE-PARTY XXX

Not used for the servicing.

MT8555 USB update

USB UPDATE

If the [

] button of the remote commander is pressed, update 

of the network processor is started.

Subwoofer + 10 dB analog mix

SW MIX +10dB XXX

Not used for the servicing.

C4 identify

C4 IDENTIFY

Not used for the servicing.

Home automation on/off

HAT XXX

Not used for the servicing.

RS232C select

232C SELECT XXXXXXX

Not used for the servicing.