Sony NW-ZX2 Service Manual ▷ View online
NW-ZX2
41
7. Remove the solder of three lead wires, and remove the lead
wires from the board. Next, solder the three lead wires to the
board, and confi rm that power supply of “WALKMAN” is
turned off.
board, and confi rm that power supply of “WALKMAN” is
turned off.
– Rear view (top side) –
Three wires
battery block
2 Solder the
wires.
1 Remove the
wires.
8. Attach the support (PWB) that were removed in step 6, con-
nect the fl exible board, to return the battery block to its original
state.
state.
battery block
– Rear view (top side) –
9. Hold down the [
1
] button on “WALKMAN”, and confi rm that
“WALKMAN” boots up normally.
(The
following
fi gure is example of display)
display
[1] button
10. Connect PC and “WALKMAN” with the USB cable for the
WM-PORT.
USB cable
Plug in the USB cable
with facing upward,
making sure the
connection is secure.
with facing upward,
making sure the
connection is secure.
11. Confi rm that the USB connection screen is displayed on
“WALKMAN”, and confi rm that charge is performed normal-
ly.
ly.
Note 2:
If the USB connection screen is not displayed, swipe the status bar
on the top of the screen then tap “Turn off USB storage” on the
notifi cation panel.
notifi cation panel.
USB storage in use
USB mass storage
6:09
Before turning off USB storage, unmount
(”eject”) your Android’s USB storage from
your computer.
Turn off USB storage
12. Assemble “WALKMAN” completely, and the confi rming is
completed.
Notes after mode completion:
Note 1:
After work is completed, uninstall the service mode tool abso-
lutely.
lutely.
(Refer to “3. UNINSTALLING METHOD OF THE SERVICE
MODE TOOL” on page 33 about procedure)
MODE TOOL” on page 33 about procedure)
Note 2:
When this unit connects with some site in order to perform the
operation check (When the connection with WiFi and the opera-
tion check of browser, etc. are performed etc.), the WiFi setting
list and the history of browser, etc. remain on this unit.
tion check of browser, etc. are performed etc.), the WiFi setting
list and the history of browser, etc. remain on this unit.
In that case, perform reset and initialization with reference to
page 11.
(When initialization is performed, all user informations are
cleared)
42
NW-ZX2
SECTION 4
EXPLODED VIEWS
1
X-2591-263-1 SVX GRIP ASSY (Including Adhesive Sheet)
2
3-234-449-35 SCREW (M1.4) (L=3.5 mm)
3
4-542-573-01 PANEL (REAR BOTTOM)
4
4-548-975-01 CUSHION (ESCUTCHEON CARD)
5
4-545-034-01 SHEET (CAPACITOR), PROTECTION
6
4-562-910-01 CUSHION (HOLDER CAP)
7
3-234-449-37 SCREW (M1.4) (L=4.0 mm)
8
4-542-572-01 PANEL
(CONTACT)
9
4-566-912-01 CUSHION (CONN SUPPORT)
10
4-545-100-01 SHEET (NFC FPC)
11
4-538-017-01 HI-RES LABEL (See Note)
ANT1 1-754-939-11 ANTENNA,
BT/WIFI/GPS
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
Note:
• -XX and -X mean standardized parts, so
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
original one.
• Items marked “*” are not stocked since
they are seldom required for routine ser-
vice. Some delay should be anticipated
when ordering these items.
vice. Some delay should be anticipated
when ordering these items.
• The mechanical parts with no reference
number in the exploded views are not sup-
plied.
plied.
• Color Indication of Appearance Parts Ex-
ample:
KNOB, BALANCE (WHITE) . . . (RED)
Parts Color Cabinet’s Color
4-1. GRIP SECTION
• Rear view
7
2
2
4
6
8
8
5
2
2
3
9
7
10
battery section
ANT1
1
11
Note: Refer to page 47 for more about the pastinging position of HI-
RES LABEL (Ref. No. 11).
43
NW-ZX2
4-2. BATTERY SECTION
• Rear view
51
3-234-449-63 SCREW (M1.4) (L=3.0 mm)
52
4-181-594-01 SHEET
(HINGE_SHUFFLE)
ADHESIVE
53
4-545-036-01 SHEET
(CAPACITOR),
ADHESIVE
54
A-2064-872-A EDLC BOARD, COMPLETE
55
4-543-788-01 SUPPORT
(PWB)
56
4-544-868-01 SHEET
(FPC
TP),
ADHESIVE
57
4-479-667-01 SHEET
(CASE
TOP),
ADHESIVE
58
3-234-449-71 SCREW (M1.4) (L=5.0 mm)
59
4-542-570-01 HOLDER
(CAP)
60
4-545-231-01 SPACER (BATT) (Former type) (See Note 1)
60
4-545-231-02 SPACER (BATT) (New type) (See Note 1)
ANT2
X-2591-522-1 SVX PANEL (REAR TOP) ASSY
(Including NFC Antenna, Adhesive Sheet (BATT),
Protection Sheet (BATT))
BAT1 X-2591-264-1 SVX
BATTERY
ASSY
(Including Battery Recycle Label) (See Note 2)
C1
1-120-056-11 CAP, ELECTRIC DOUBLE LAYERS 0.35F
WR1
1-970-724-11 EDLC+ OFC WIRE (WHITE)
WR2
1-970-725-11 EDLC- OFC WIRE (BLACK)
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
Note 2:
• When removing battery assy (Ref. No. BAT1) from the SVX panel
• When removing battery assy (Ref. No. BAT1) from the SVX panel
(REAR TOP) assy (Ref. No. ANT2), it is not re-used. Be sure to re-
place them with new parts.
place them with new parts.
• When disposing battery assy (Ref. No. BAT1) without an affi xed bat-
tery recycle label, affi xing a battery recycle label before disposal is
required.
required.
Refer to “NOTE OF DISPOSAL OF THE LITHIUM ION STORAGE
BATTERY PACK” on page 4.
• When battery assy (Ref. No. BAT1) is replaced, refer to “ABOUT
THE REPLACING OF THE BATTERY ASSY (BAT1)” on page 4
and “4-3. BATTERY” on page 39.
and “4-3. BATTERY” on page 39.
• When the battery wire is removed, refer to “ABOUT INSULATING
OF LITHIUM ION STORAGE BATTERY PACK” on page 4.
C
51
55
56
53 54
58
MAIN board section
A
A
C
B
51
52
59
52
57
B
BAT1
ANT2
WR1
WR2
C1
60
60
(New)
(Former)
Note 1:
The shape of the spacer (BATT) (Ref. No. 60) has been changed
from the midway of production.
from the midway of production.
When repairing or replacing, confi rm the shape of the part.
Former type : No holes, with a battery recycle label
New type
: Holes, without a battery recycle label
44
NW-ZX2
4-3. MAIN BOARD SECTION
• Rear view
101
3-234-449-39 SCREW (M1.4) (L=4.0 mm)
102
4-547-459-01 CUSHION (HOLDER MULTI)
103
4-562-909-01 SHEET (PROTECTION L)
104
3-234-449-23 SCREW (M1.4) (L=2.2 mm)
105
9-885-201-60 MAIN BOARD, COMPLETE (SV)
(Including Cushions) (EXCEPT CH) (See Note)
105
9-885-201-61 MAIN BOARD, COMPLETE (SV)
(Including Cushions) (CH) (See Note)
106
4-562-615-01 SHEET
(CPU)
107
4-542-569-01 HOLDER
(MULTI)
108
4-548-975-01 CUSHION (ESCUTCHEON CARD)
109
4-543-749-01 SHEET (HOLDER CONN), ADHESIVE
110
4-547-218-01 SHEET
(LOGO),
ADHESIVE
111
4-542-567-01 HOOK
(JACK)
112
4-543-754-01 SHEET (HOOK JACK)
113
4-543-750-01 SHEET (HOLDER JACK), ADHESIVE
114
4-542-568-01 HOLDER (JACK OUTER)
HP1
X-2591-265-1 SVX HP ASSY (Including HP Board, Jack, Wire)
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
Note:
• When MAIN board is replaced, the data writing processing etc. are
• When MAIN board is replaced, the data writing processing etc. are
necessary. For details, refer to “NOTE OF REPLACING THE MAIN
BOARD” on page 4.
BOARD” on page 4.
• For the handling of the MAIN board, refer to “NOTE OF HANDLING
THE MAIN BOARD” on page 11.
LCD section
101
104
104
104
104
105
107
108
109
104
104
104
104
112
111
110
113
114
102
103
D
D
E
E
F
F
G
G
HP1
H
H
106
Click on the first or last page to see other NW-ZX2 service manuals if exist.