Sony NW-ZX2 Service Manual ▷ View online
NW-ZX2
25
2-12. MAIN BOARD-1
• Continued on 2-13 (page 26).
– Rear top view –
3DVWLQJSRVLWLRQRIWKHFXVKLRQ
(HOLDER MULTI)
(HOLDER MULTI)
3DVWLQJSRVLWLRQRIWKHVKHHW
3527(&7,21/
3527(&7,21/
6 KEY-NFC-TP flexible board
3 cushion
(HOLDER
MULTI)
2 cushion
(ESCUTCHEON
CARD)
1 sheet
(PROTECTION
L)
guide line
guide line
cushion (HOLDER MULTI)
MAIN board
sheet (PROTECTION L)
LCD flexible board
guide line
guide line
MAIN board
MAIN board
OK
1*
1*
4 LCD flexible board
,QVWDOODWLRQSRVLWLRQRIWKH/&'IOH[LEOHERDUG
two ribs
two grooves
Note 1: There is a possibility of damaging LCD flexible board
when removing the direction of below figure of “NG”.
Note 2: When installing LCD flexible board,
align two grooves and two ribs.
If putting into the connector shift
groove and rib, connector will be
broken.
1RWHVIRUUHPRYLQJWKH/&'IOH[LEOHERDUG
NW-ZX2
26
2-13. MAIN BOARD-2
2-14. ESCUTCHEON (MULTI)
– Rear top view –
hole
hole
groove
rib
rib
5 Draw the MAIN
board block out
of the hole.
2 eight screws
(M1.4) (L=2.2 mm)
7 sheet (CPU)
6 MAIN board block
1 screw (M1.4)
(L=4.0
mm)
4 Open the KEY-NFC-TP flexible board
in the direction of the arrow.
3 Open the LCD flexible board
in the direction of the arrow.
8 MAIN board
Note
2: Refer to “NOTE OF HANDLING
THE MAIN BOARD” on page 11.
– Rear top view –
5 escutcheon (MULTI)
1 collar
1 collar
hole
3 Draw the escutcheon (MULTI)
block out of the hole.
4 adhesive sheet (MULTI)
2 Peel off the adhesion part.
Note 1:
When MAIN board is replaced, the data writing processing etc. are necessary.
For details, refer to “NOTE OF REPLACING THE MAIN BOARD” on page 4.
NW-ZX2
27
2-15. LCD MODULE (LCD1)
adhesive sheet
(FPC TP)
(FPC TP)
qd HI-RES label
3DVWLQJSRVLWLRQRIWKHFXVKLRQ
/,*+73527(&7,21
/,*+73527(&7,21
5 Peel off the LCD module flexible board
from the adhesive sheet (LCD FPC).
Note
Note
1: Please peel off carefully so
as not to damage.
–5HDUWRSYLHZ–
2 protection sheet
(FPC
TP)
3 LCD module flexible board
0 adhesive sheet
(WINDOW_TOP)
–5HDUERWWRPYLHZ–
hole
6 Peel off the adhesive sheet
(WINDOW_SIDE) from
the cabinet block.
7 Peel off the adhesive sheet
(WINDOW_SIDE)
from
the cabinet block.
8 Peel off the LCD module block from
the adhesive sheet (WINDOW_BOTTOM).
cabinet block
9 Draw the LCD module flexible board
out of the hole.
Note
2: Please pull it out carefully so
as not to damage.
qa adhesive sheet (WINDOW_SIDE)
qa adhesive sheet
(WINDOW_SIDE)
qs adhesive sheet
(FPC
TP)
qf LCD module (LCD1)
7 Peel off the adhesive sheet (WINDOW_SIDE)
from the cabinet block.
–/&'PRGXOHIURQWYLHZ–
HI-RES label
3DVWLQJSRVLWLRQRIWKH+,5(6ODEHO
3DVWLQJSRVLWLRQRIWKHDGKHVLYHVKHHW)3&73
3 mm
3 mm
LCD module (LCD1)
KEY-NFC-TP flexible board
cushion (LIGHT PROTECTION)
1 cushion (LIGHT PROTECTION)
guide line
guide line
LCD module flexible board
adhesive sheet
(LCD FPC)
(LCD FPC)
adhesive sheet
(HINGE_SHUFFLE)
(HINGE_SHUFFLE)
4 Peel the LCD module flexible board off of
the adhesive sheet (HINGE_SHUFFLE).
NW-ZX2
28
2-16. KEY-NFC-TP FPC BOARD (FPC1)
2-17. SHEET (LCD), SUPPORT (CHASSIS)
KEY-NFC-TP FPC board (FPC1)
3DVWLQJSRVLWLRQRIWKHDGKHVLYHVKHHW/&'B)3&
–5HDUWRSYLHZ–
adhesive sheet
(LCD_FPC)
(LCD_FPC)
1 two screws (M1.4)
(L=2.5
mm)
2 Peel the adhesive sheet (LCD_FPC)
off of the cabinet block.
3 adhesive sheet
(LCD_FPC)
hole
hole
two holes
4 panel (SIDE) block
total six switches
total six buttons
Note 2: When installing the KEY-NFC-TP FPC board
(FPC1), align six buttons and six switches.
(FPC1), align six buttons and six switches.
5 KEY-NFC-TP FPC board (FPC1)
Note
1: When installing the KEY-NFC-TP FPC board (FPC1),
align the KEY-NFC-TP FPC board (FPC1) two holes
and the panel (SIDE) block two holes.
guide line
3DVWLQJSRVLWLRQRIWKHVKHHW/&'
4 support (CHASSIS)
3 three claws
guide line
1 sheet (LCD)
sheet (LCD)
2 two claws
Click on the first or last page to see other NW-ZX2 service manuals if exist.