Sony NW-ZX2 Service Manual ▷ View online
NW-ZX2
17
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
2-10. HOLDER (MULTI)
(Page
(Page
23)
SET
2-9. HOLDER
(CAP)
(Page
23)
2-2. GRIP
ASSY
(Page
17)
2-3. PANEL
(REAR
(REAR
BOTTOM)
(Page
18)
2-4. BT/WIFI/GPS
ANTENNA
ANTENNA
(ANT1)
(Page
18)
2-5. BATTERY
ASSY
(BAT1)-1
(Page
19)
2-7. BATTERY
ASSY
(BAT1)-3
(Page
21)
2-8. EDLC
BOARD
(Page
22)
2-6. BATTERY
ASSY
(BAT1)-2
(Page
20)
2-11. HP ASSY (HP1)
(Page
(Page
24)
2-12. MAIN BOARD-1
(Page
(Page
25)
2-13. MAIN BOARD-2
(Page
(Page
26)
2-14. ESCUTCHEON (MULTI)
(Page
(Page
26)
2-15. LCD MODULE (LCD1)
(Page
(Page
27)
2-18. SPACER (CHASSIS)
(Page
(Page
29)
2-17. SHEET (LCD),
SUPPORT
SUPPORT
(CHASSIS)
(Page
28)
2-19. SUPPORT (LCD FPC)
BLOCK, SPACER (AU)
(Page
29)
2-20. CHASSIS BLOCK
(Page
(Page
30)
2-21. CHASSIS ASSY
(Page
(Page
30)
2-16. KEY-NFC-TP FPC BOARD
(FPC1)
(Page
(FPC1)
(Page
28)
– Top view –
– Top view –
– Side view –
There is gap.
There is no gap.
Floating.
NG
OK
NG
Note of installing the grip assy
– Rear top view –
1 Peel off the adhesive sheet.
2 grip assy
Note: When removing grip assy, it is not re-used.
Be sure to replace them with new parts.
Note:
Follow the disassembly procedure in the numerical order given.
2-2. GRIP
ASSY
NW-ZX2
18
2-3. PANEL (REAR BOTTOM)
2-4. BT/WIFI/GPS ANTENNA (ANT1)
2 panel (REAR BOTTOM)
1 two screws
(M1.4) (L=3.5 mm)
1 two screws
(M1.4) (L=3.5 mm)
– Rear top view –
– Rear top view –
4 BT/WIFI/GPS
antenna
block
2 two
claws
1 screw (M1.4)
(L=4.0
mm)
3 two ribs
1 screw (M1.4)
(L=4.0
mm)
6 BT/WIFI/GPS
antenna
(ANT1)
5 panel (CONTACT)
5 panel (CONTACT)
NW-ZX2
19
2-5. BATTERY ASSY (BAT1)-1
• Continued on 2-6 (page 20).
– Rear top view –
3aVtiQJ poVitioQ oI tKe FXVKioQ +2/'(R &$3
3aVtiQJ poVitioQ oI tKe VKeet 1)& )3&
6 screw (M1.4)
(L=3.0
mm)
6 screw (M1.4)
(L=3.0
mm)
0 support
(PWB)
block
1 cushion
(CONN
SUPPORT)
7 cushion
(HOLDER
CAP)
2 sheet (NFC FPC)
3 Remove the NFC antenna connector.
cushion
(HOLDER CAP)
(HOLDER CAP)
holder
(CAP)
(CAP)
sheet (NFC FPC)
NFC antenna
adhesive sheet
(HINGE_SHUFFLE)
(HINGE_SHUFFLE)
battery block
MAIN board
guide line
guide line
8 Remove the battery block
in the direction of the arrow.
4 Peel the NFC antenna off
of the adhesive sheet
(HINGE_SHUFFLE).
9 Peel off the adhesive
sheet (FPC TP).
5 Peel off the KEY-NFC-TP
flexible
board.
NW-ZX2
20
2-6. BATTERY ASSY (BAT1)-2
• Continued on 2-7 (page 21).
battery assy
(BAT1)
(BAT1)
battery wire
[black]
[black]
battery wire
[red]
[red]
MAIN board
MAIN board
MAIN board
MAIN board
EDLC board
EDLC board
EDLC+OFC
wire [white]
wire [white]
EDLC-OFC
wire [black]
wire [black]
:LUHVHWWLQJ
battery assy
(BAT1)
(BAT1)
battery wire
[white]
[white]
A
A
–5HDUWRSYLHZ–
4 Remove two solders of battery wire.
Note
4: When the battery wire is removed,
refer to “ABOUT INSULATING OF
LITHIUM ION STORAGE BATTERY
PACK” on page 4.
1 Remove the solders of battery wire.
Note
4: When the battery wire is removed,
refer to “ABOUT INSULATING OF
LITHIUM ION STORAGE
BATTERY PACK” on page 4.
[red]
[white]
[black]
2 Remove the solder
of EDLC-OFC wire.
[black]
3 Remove the solder
of EDLC+OFC wire.
[white]
5 battery block
adhesive sheet (HINGE_SHUFFLE)
guide line
3DVWLQJSRVLWLRQRIWKHDGKHVLYH
VKHHW+,1*(B6+8))/(
VKHHW+,1*(B6+8))/(
Click on the first or last page to see other NW-ZX2 service manuals if exist.