Sony NW-ZX2 Service Manual ▷ View online
NW-ZX2
21
2-7. BATTERY ASSY (BAT1)-3
– Battery block rear top view –
5 battery assy (BAT1)
Note
Note
1: When removing battery assy (BAT1)
from the adhesive sheet (BATT),
it is not re-used.
Be sure to replace them with new parts.
Note
2: When battery assy (BAT1) is replaced,
refer to “ABOUT THE REPLACING
OF THE BATTERY ASSY (BAT1)”
on page 4.
Note
3: When disposing battery assy (BAT1),
refer to “NOTE OF DISPOSAL OF
THE LITHIUM ION STORAGE
BATTERY PACK” on page 4.
3 panel (REAR TOP) assy (ANT2)
1 Peel the battery assy (BAT1) off
of the adhesive sheet (BATT).
Note
1: When removing battery assy (BAT1)
from the adhesive sheet (BATT),
it is not re-used.
Be sure to replace them with new parts.
2 Draw the wire out of the hole in
panel (REAR TOP) assy (ANT2).
hole
1 Pass the wires through the hole of the panel
(REAR TOP) assembly (ANT2).
2 Align the battery assy (BAT1)
with the guide line and attach.
hole
guide line
How to install the battery assy (BAT1) and spacer (BATT)
guide line
panel (REAR TOP)
assy (ANT2)
assy (ANT2)
panel (REAR TOP)
assy (ANT2)
assy (ANT2)
battery assy
(BAT1)
(BAT1)
battery assy (BAT1)
4 spacer (BATT)
Note
Note
4: The shape of the spacer (BATT) has been
changed from the midway of production.
3 Align the spacer (BATT) with
the guide line and affix.
Note
4: The shape of the spacer (BATT) has
been changed from the midway of
production.
NW-ZX2
22
2-8. EDLC BOARD
– Rear top view –
5 adhesive sheet
(CAPACITOR)
4 electric double
layers cap (C1)
1 cushion
(ESCUTCHEON
CARD)
2 protection sheet
(CAPACITOR)
adhesive sheet
(CAPACITOR)
(CAPACITOR)
protection sheet
(CAPACITOR)
(CAPACITOR)
guide line
guide line
guide line
guide line
EDLC board
guide line
3DVWLQJSRVLWLRQRIWKHDGKHVLYHVKHHW&$3$&,725
3DVWLQJSRVLWLRQRIWKHSURWHFWLRQVKHHW&$3$&,725
:LUHVHWWLQJ
hole
groove
3 Remove the three solders.
rib
rib
adhesive sheet
(HINGE_SHUFFLE)
(HINGE_SHUFFLE)
adhesive sheet
(CASE TOP)
(CASE TOP)
6 Peel the EDLC board block off of
the adhesive sheet (CASE TOP)
and adhesive sheet
(HINGE_SHUFFLE).
8 EDLC board
Note: When installing the EDLC board,
align the rib and hole.
EDLC+OFC
wire [white]
wire [white]
EDLC-OFC
wire [black]
wire [black]
7 Remove the solder
of EDLC-OFC wire.
[black]
7 Remove the solder
of EDLC+OFC wire.
[white]
NW-ZX2
23
2-9. HOLDER
(CAP)
2-10. HOLDER (MULTI)
– Rear top view –
1 screw (M1.4)
(L=5.0
mm)
5 holder (CAP)
2 Peel the holder (CAP) block off of
the adhesive sheet (LOGO).
3 adhesive sheet (HINGE_SHUFFLE)
4 adhesive sheet (CASE_TOP)
– Rear top view –
3 holder (MULTI)
1 Peel off the adhesion part.
2 adhesive sheet (HOLDER CONN)
NW-ZX2
24
2-11. HP ASSY (HP1)
– Rear top view –
– Rear bottom view –
8 hook (JACK)
9 HP assy (HP1)
6 sheet (HOOK JACK)
hook (JACK)
Lock the hook (JACK).
Rotate the hook (JACK)
in the direction of the arrow.
in the direction of the arrow.
+ow to iQVtaOO oI tKe KooN -$&.
5 holder (JACK OUTER) block
4 Peel off the adhesive sheet
(HOLDER
JACK).
7 Rotate the hook (JACK) in the
direction of the arrow and unlock.
:ire VettiQJ
[black]
[red]
MAIN board
MAIN board
[black (with shrinkable tube)]
[black (thick)]
[white (thick)]
[white (with shrinkable tube)]
3 Remove the
two
solders.
2 Remove the
two
solders.
1 Remove the
two
solders.
Click on the first or last page to see other NW-ZX2 service manuals if exist.