Sony HCD-V909AV / MHC-V909AV Service Manual ▷ View online
— 94 —
Pin No.
Pin Name
I/O
Function
• IC701 MASTER CONTROL (uPD780016YGF-019-3BA)/MAIN board
1
TA-MUTE
O
Line mute signal output
2
DBFB-H/L
O
DBFB H/L select signal output
3
427-LAT
O
Latch signal output for IC201 (62427)
4
K-CON-LAT
O
Latch signal output for key control
5
K-CON-ON
O
Key control ON/OFF signal output
6
F-RELAY
O
Front speaker relay control output (Not used)
7
R-RELAY
O
Rear speaker relay control output
8
PL-RELAY
O
Not used
9
TEST
I
Connected to ground
10
X2
O
X’tal (5MHz)
11
X1
I
12
VDD
–
Power supply (+5V)
13
XT2
O
X’tal (32.768 KHz)
14
XT1
I
15
RESET
I
Reset signal input
16
INT/IN
I
Connected to ground
17
INT/IN/OUT
I
18
SCOR
O
Not used
19
SOFT-TEST
O
Software test port
20
AC-CUT
I
Back up signal input
21
RDS-INT
I
Not used
22
RDS-DATA
I
Not used
23
VDD
–
Power supply (+5V)
24
AVDD
I
Analog reference voltage input.
25
ADJ
I
CD adjust point port
Normal “H”
26
A-SHUT
I
A Deck reel pulse detector
27
B-SHUT
I
B Deck reel pulse detector
28
B-HALF
I
Half detector signal input
29
CLK-CHECK
I
Connected to ground
30
SPEC-IN
I
Connected to ground
31
ADJ 2
I
Connected to ground
32
DEMO-MODE
I
Connected to ground
33
AVSS
–
Ground
34
SQ-DATA-IN
I
Subcode Q data clock input (Not used)
35
NC
I
Not used
36
D.OUT ON/OFF
O
CD digital out ON/OFF control
37
SW-ON/OFF
O
Not used
38, 39
FUNC 1, 2
I
Connected to ground
40
VSS
–
Ground
41
VOL-LAT
O
Latch signal to erectrial volume (IC604)
42
PL-LAT
O
Latch signal to pro-logic (IC601, 602)
43
COM-DIN
I
Connected to ground
44
COM-DOUT
O
Common serial data output
45
COM-CLK
O
Common serial clock output
46
CD-POWER
O
CD power on signal output
47
CD-DATA
O
CD data output (Not used)
48
CD-CLK
O
CD clock output (Not used)
49
MSM-CND
O
Not used
50
MSM-BUSY
I
Connected to ground
— 95 —
Pin No.
Pin Name
I/O
Function
51
MSM-LAT
O
52
MSM-NAR
I
Not used
53
MSM-CH
O
54
INPUT-CHANGE
O
Input sensitivity switching output
55
IIC-DATA
O
Data output for IC601, 901
56
IIC-CLK
O
Clock output for IC601, 901
57
XRST
O
CD reset signal output
58
XLT
O
CD latch signal output (Not used)
59
FOCUS-SW
O
Not used
60
TBL-L
O
Table motor control output
61
TBL-R
O
62
TRAY-LED
O
Not used
63
LOAD-OUT
O
Loading motor control signal output
64
LOAD-IN
O
65
ST-CLK
O
Tuner clock output
66
ST-DIN
I
Tuner data input
67
ST-DOUT
O
Tuner data output
68
ST-CE
O
Tuner chip enable output
69
TUNED
I
Tuned detection for tuner
70
STEREO
I
Stereo detection for tuner
71
VSS
–
Ground
72
ST-MUTE
O
Tuner mute signal output
73
SENS2
I
BD Condition signal input (Not used)
74
SENS
I
75
DISC-SENS
I
Slit sensor of disc table input
76
T-SENS
I
CD table detection signal input
77
UPSW
I
Up SW (S201) signal input
78
ENC 3
I
79
ENC 2
I
Disc tray address detect encoder input
80
ENC 1
I
81
OUT-OPEN
I
Loading out detection signal output
82
CAP-H/N
O
Capstan motor H/N speed select signal output
83
A-TRG
O
Trigger motor control output
84
B-TRG
O
Trigger motor control output
85
TRG-LOW
O
Trigger motor control output
86
CAP-M-ON/OFF
O
Capstan motor ON/OFF signal output
87
PB-A/B
O
PB Deck A/Deck B select output
88
EQ-H/N
O
Equalizer H/N select output
89
BIAS
O
Bias ON/OFF signal output
90
REC-MUTE
O
REC mute ON/OFF selection output
91
NR-ON/OFF
O
NR ON/OFF signal output
92
R/P-PASS
O
REC/PB/PASS selection output
93
TC-MUTE
O
TC mute ON/OFF selection output
94
A-PLAY-SW
I
Deck A play detect
95
B-PLAY-SW
I
Deck B play detect
96
RELAY
O
REC/PB head selection output for IC602
97
A-HALF
I
Deck A cassette detect
98
POWER
O
POWER ON/OFF signal output
99
SW-F-CON
O
Not used
100
STK-MUTE
O
Power amp ON/OFF signal output
— 96 —
• IC601 DISPLAY CONTROL ( TMP87CM75-6564)/PANEL board
Pin No.
Pin Name
I/O
Function
1
SEG35
O
FL segment signal output
2
VLOAD
O
Power supply (–25V) for FL segment signal output
3 to 10
LED1 to LED8
O
LED driver output
11
VSS
–
Ground
12
X-OUT
O
13
X-IN
I
14
RESET
I
Reset signal input from main controller
15
LED9
O
LED driver output
16
LED10
O
LED driver output
17
TEST
I
Connected ground
18 to 22
LED11 to LED15
O
LED driver output
23
LED16
O
LED driver output
24
VOL-A
I
Rotary encoder (S602) pulse input
25
LED17
O
LED driver output
26
JOG-A
I
Rotaly encoder (S601) pulse input
27
CLOCK
I
Serial clock input from main controller
28
DATA
I
Serial data input from main controller
29
LED SELECT
O
LED select signal output
30
VDD
–
Power supply (+5V)
31
VSS
–
Ground
32
MODEL
I
Version select signal input
33 to 37
KEY1 to KEY5
I
Key input
38
EWS STANDBY
I
Not used
39
SIRCS
I
Remote commander signal input
40
VOL-B
I
Rotary encoder (S602) pulse input
41
JOG-B
I
Rotary encoder (S601) pulse input
42
SPEANA-1
I
Spectrum analyzer input
43
SPEANA-2
I
Spectrum analyzer input
44
SPEANA-3
I
Spectrum analyzer input
45
SPEANA-4
I
Spectrum analyzer input
46
L + R
I
Spectrum analyzer (high frequency) input
47
EWS SIGNAL/LED18
O
Not used
48
VASS
–
Ground
49
VAREF
I
Analog reference voltage input
50
VDD
–
Power supply (+5V)
51 to 56
GR1 to GR16
O
FL gride signal output
67 to 100
SEG1 to SEG34
O
FL segment signal output
X’tall (8MHz)
• Abbreviation
FL : Fluorescent indicator tube
— 97 —
SECTION 8
EXPLODED VIEWS
NOTE:
• Items marked “*” are not stocked since they are
seldom required for routine service. Some delay
should be anticipated when ordering these items.
should be anticipated when ordering these items.
• The mechanical parts with no reference number in
the exploded views are not supplied.
• Hardware (# mark) list and accessories and pack-
ing materials are given in the last of this parts list.
The components identified by
mark
mark
! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
Replace only with part number
specified.
• Abbreviation
SP : Singapore model.
IA : Indonesia model.
MY : Malaysia model.
TH : Thai model.
CH : Chinese model.
IA : Indonesia model.
MY : Malaysia model.
TH : Thai model.
CH : Chinese model.
8-1. CASE SECTION
CDM-38L-5BD21AL
#1
#1
#1
#1
#1
#1
not supplied
not supplied
not supplied
not supplied
#2
#1
#4
FRONT PANEL
#2
#4
#1
#4
#1
#1
10
9
3
7
5
6
11
10
9
4
8
13
12
1
2
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
1
4-991-782-21 PANEL, LOADING
2
4-991-781-01 EMBLEM (VCD)
3
4-965-822-01 FOOT
4
A-4398-587-A VIDEO BOARD, COMPLETE
5
1-773-158-11 WIRE (FLAT TYPE) (21 CORE)
6
1-773-051-11 WIRE (FLAT TYPE) (17 CORE)
7
1-769-948-11 WIRE (FLAT TYPE) (11 CORE)
8
1-782-653-11 WIRE (FLAT TYPE) (13 CORE)
9
3-363-099-01 SCREW (CASE 3 TP2)
10
3-363-099-41 SCREW (CASE 3 TP2)
* 11
4-988-767-21 CASE (CH)
* 11
4-988-767-61 CASE (EXCEPT CH)
* 12
1-666-126-11 VIDEO POWER BOARD
13
1-782-654-11 WIRE (FLAT TYPE) (29 CORE)
Click on the first or last page to see other HCD-V909AV / MHC-V909AV service manuals if exist.