Sony HBD-NF7220 Service Manual ▷ View online
HBD-NF7220
13
AMP BOARD SERVICE POSITION
MB1305 BOARD SERVICE POSITION
switching regulator
AMP board
MB1305 board
switching regulator
HBD-NF7220
14
SECTION 2
DISASSEMBLY
•
This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
2-2. COVER
(TOP)
(Page
15)
SET
2-3. TOUCH_F BOARD, TOUCH_S BOARD BLOCK
(Page
(Page
16)
2-4. INNER DOOR BLOCK
(Page
(Page
17)
2-5. COVER (BU TOP)
(Page
(Page
18)
2-7. OPTICAL DEVICE BLOCK
(Page
(Page
20)
2-9. OPTICAL DEVICE KEM480AHA/C2RP1 (OP1)
(Page
(Page
22)
2-8. FLEXIBLE FLAT CABLE (45 CORE), WIRE (FLAT TYPE) (9 CORE),
WIRE (FLAT TYPE) (5 CORE)
(Page
21)
2-6. LOADING
ASSY
BLOCK
(Page
19)
2-11. WLAN/BT COMBO CARD
(Page
(Page
24)
2-12. FL+CHUKEI BOARD
(Page
(Page
24)
2-13. LED CHUKEI BOARD
(Page
(Page
25)
2-14. FUSB+SIRCS BOARD
(Page
(Page
25)
2-15. AUDIO IO BOARD
(Page
(Page
26)
2-16. SHIELD (POWER) BLOCK
(Page
(Page
26)
2-17. MB1305 BOARD
(Page
(Page
27)
2-18. DC FAN
(Page
(Page
28)
2-20. AMP BOARD
(Page
(Page
29)
2-19. POWER CORD
(Page
(Page
28)
2-21. SWITCHING REGULATOR
(Page
(Page
30)
2-10. COVER (BOTTOM) BLOCK
(Page
(Page
23)
2-22. HOW TO BEND FFC
(Page
(Page
31)
HBD-NF7220
15
Note: Follow the disassembly procedure in the numerical order given.
2-2. COVER (TOP)
– Bottom view –
2 plate (BD-H)
front side
Note: When installing the plate (BD-H),
check the installation orientation.
plate (BD-H)
slot
4 Open the cover (top) assy fully.
1 one screw
(PTP2
u 5)
5 Remove the cover (top) assy
in the direction of an arrow.
6 total twenty one claws
7 cover (top) assy
3 Insert a screwdriver and
turn the cam gear in the
direction of an arrow.
direction of an arrow.
cam gear
HBD-NF7220
16
2-3. TOUCH_F BOARD, TOUCH_S BOARD BLOCK
2 stopper (front)
4 stopper (rear)
1 two screws
(+BTP
2
u 6)
3 two screws
(+BTP
2
u 6)
5 two screws
(+BV3
(3-CR))
6 Remove the TOUCH_F, TOUCH_S board block
in the direction of an arrow.
7 three claws
7 claw
7 three claws
8 wire (flat type) (26 core)
(CN2301)
9 TOUCH_F board, TOUCH_S board block
colored line
colored line
Inserting is straight to the interior.
Inserting is slant.
wire (flat type)
wire (flat type)
connector
connector
OK
NG
Note: When installing the wire (flat type), ensure the colored line.
No slanting after insertion.
Click on the first or last page to see other HBD-NF7220 service manuals if exist.