Sony DAV-TZ215 / DAV-TZ715 / HBD-TZ215 / HBD-TZ715 Service Manual ▷ View online
HBD-TZ215/TZ715
13
2-9. MAIN BOARD
5 connector
(CN2101)
7 connector
(CN906)
8 connector
(CN904)
6 wire (flat type) (11 core)
(CN506)
1 two screws
(BV3 (3-CR))
9 four screws
(BV3 (3-CR))
0 heat sink block
qa holder (IC)
qs three screws
(BV3 (3-CR))
qs two screws
(BV3 (3-CR))
qd MAIN board
2 insulated plate
(POW)
3 shield plate (PC)
4 Lift up two lead pins.
A
A
Note: When the heat sink has been removed,
apply oil compound (G-747) to it.
$UUDQJLQJWKH86%ZLUH
Have the USB wire spread on the inside
of the claws of the chassis.
of the claws of the chassis.
USB wire
USB wire
heat sink
heat sink
CN3000
CN509
CN906
red
black
Tie up with LP3002.
Tie up with LP501.
Draw the USB wire through CN3000.
Keep a distance of more than 6.5 mm
between the wire and CN901.
between the wire and CN901.
Keep the wire tied up from lying on
the heat sink and the POWER board.
the heat sink and the POWER board.
Keep the wire tied up from lying on
the heat sink and the POWER board.
the heat sink and the POWER board.
POWER board
CN901
$(3&KLQHVH6DXGL$UDELD
Ver. 1.2
HBD-TZ215/TZ715
14
2-10. POWER BOARD
0 POWER board
6 two claws
8 four screws
(BV3 (3-CR))
8 four screws
(BV3 (3-CR))
5 screw
(BV3 (3-CR))
7 plate flow control (AMP)
9 holder PC board
1 power cord connector
(CN901)
3 connector
(CN904)
4 connector
(CN906)
2 Lift up two lead pins.
CN901
LF901
POWER board
3RZHUFRUGVHWWLQJ
6 mm
rear side
$UUDQJLQJWKH86%ZLUH
Have the USB wire spread on the inside
of the claws of the chassis.
of the claws of the chassis.
USB wire
USB wire
heat sink
heat sink
CN3000
CN509
CN906
red
black
Tie up with LP3002.
Tie up with LP501.
Draw the USB wire through CN3000.
Keep a distance of more than 6.5 mm
between the wire and CN901.
between the wire and CN901.
Keep the wire tied up from lying on
the heat sink and the POWER board.
the heat sink and the POWER board.
Keep the wire tied up from lying on
the heat sink and the POWER board.
the heat sink and the POWER board.
POWER board
CN901
HBD-TZ215/TZ715
15
2-11. FFC HOLDER
1 two claws
2
1 two claws
1 Insert the wire (flat type) (24 core)
to the FFC holder.
FFC holder
2 Hang the wire (flat type) (24 core)
on two claws of the FFC holder.
5 two claws
3 wire (flat type) (24 core)
6 wire (flat type) (24 core)
4 FFC holder block
– DVD mechanism deck bottom view –
+ow to instaOO wiUe IOat t\Se coUe
7 FFC holder
Note: Remove the FFC holder from the
original set and install it again.
3 Pass a long side of wire
(flat type) (24 core) through
the hole of the FFC holder.
4 Pass a short side of wire
(flat type) (24 core) through
the hole of the FFC holder.
HBD-TZ215/TZ715
16
2-12. OPTICAL PICK-UP (KHM-313CAA)
2-13. BELT
5 optical pick-up
(KHM-313CAA)
1 two insulator screws
1 two insulator screws
3 insulator
3 insulator
3 insulator
3 insulator
4 connector
2 loading assy (M)
– DVD mechanism deck bottom view –
1 Push the lever in the
direction of the arrow.
3 claw
3 claw
5 two hooks
6 shaft
7 chuck cam
8 belt
2
bottom side
4 tray
Click on the first or last page to see other DAV-TZ215 / DAV-TZ715 / HBD-TZ215 / HBD-TZ715 service manuals if exist.