Sony DAR-RH1000 / DAR-RH7000 / HCD-RH1000 / HCD-RH7000 Service Manual ▷ View online
5
HCD-RH1000/RH7000
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
CHECK
Carry out the “S curve check” in “CD section adjustment” and check
that the S curve waveforms is output three times.
that the S curve waveforms is output three times.
NOTES DURING THE FORCED EJECTION
1. If the forced ejection is executed while a blank disc media
(DVDRW,
±R) exists on the tray.
• Insert a DVD-ROM (DVD test disc, DVD software available
on the market, or the like) in the tray and then close the tray.
Note1:
If you close the tray while it is empty, ejection of the tray
becomes impossible.
becomes impossible.
Note2:
If you close the tray with a CD disc inserted in it, the CD can
be ejected. However, if you close the tray while it is empty,
there can be a case that ejection of the tray becomes
impossible.
be ejected. However, if you close the tray while it is empty,
there can be a case that ejection of the tray becomes
impossible.
Note3:
Even if you replace the DVD drive unit while the tray remains
under the state as described above, the situation cannot be
improved.
under the state as described above, the situation cannot be
improved.
2. If the tray cannot be ejected while the disc is not inserted.
• Execute the forced ejection.
• Insert a DVD-ROM (DVD test disc, DVD software available
on the market, or the like) on the tray and try to close the tray.
(There are cases that it recovers the trouble)
3. Contents of forcedly ejected blank disc media (DVDRW,
±R)
can be damaged. (There can be a case that initialization is also
impossible)
impossible)
DISC REMOVAL PROCEDURE IF THE TRAY CANNOT BE EJECTED (FORCED EJECTION)
1. Remove the upper case.
2. Remove the RD-053AU board, RD bracket.
3. Insert and push the stiff wire in the hole and eject the tray.
2. Remove the RD-053AU board, RD bracket.
3. Insert and push the stiff wire in the hole and eject the tray.
stiff wire
tray
hole
6
HCD-RH1000/RH7000
Playable discs
“DVD VIDEO” and “CD” are trademarks.
Discs that cannot be played
• PHOTO CDs
• CD-ROMs/CD-Rs/CD-RWs that are not
• CD-ROMs/CD-Rs/CD-RWs that are not
recorded in music CD or Video CD format, or do
not contain MP3 or JPEG files
not contain MP3 or JPEG files
• Data part of CD-Extras
• DVD-ROMs that are not recorded in DVD
• DVD-ROMs that are not recorded in DVD
Video format
• DVD Audio discs
• DVD-RAMs
• HD layer on Super Audio CDs
• DVD VIDEOs with a different region code
• DVD-Rs recorded in VR mode (Video
• DVD-RAMs
• HD layer on Super Audio CDs
• DVD VIDEOs with a different region code
• DVD-Rs recorded in VR mode (Video
Recording format)
Note
When playing DTS surround sound on a CD or DVD,
you can hear the sound from this speaker system only.
The audio signals are not output from the LINE output
jacks on the recorder.
you can hear the sound from this speaker system only.
The audio signals are not output from the LINE output
jacks on the recorder.
Type
Disc logo
Icon used
in this
manual
in this
manual
Characteristics
DVD VIDEO
Discs such as movies that can be purchased or
rented.
rented.
DVD-R DL
—
DVD-R Dual Layer discs that were recorded on
other equipment. This recorder recognizes
DVD-R Dual Layer discs as DVD Video
compatible discs.
other equipment. This recorder recognizes
DVD-R Dual Layer discs as DVD Video
compatible discs.
VIDEO CD
VIDEO CDs or CD-Rs/CD-RWs in VIDEO
CD/Super VIDEO CD format.
CD/Super VIDEO CD format.
CD
Music CDs or CD-Rs/CD-RWs in music CD
format that can be purchased.
format that can be purchased.
DATA CD
—
CD-ROMs/CD-Rs/CD-RWs containing MP3
audio tracks or JPEG image files.
audio tracks or JPEG image files.
8 cm DVD+RW/
DVD-RW/DVD-R
DVD-RW/DVD-R
—
—
8 cm DVD+RW, DVD-RW, and DVD-R
recorded with a DVD video camera.
(Still images recorded with a DVD video
camera cannot be played.)
recorded with a DVD video camera.
(Still images recorded with a DVD video
camera cannot be played.)
DVD
DVD
VCD
CD
DATA CD
Maximum recordable number of titles
* The maximum length for each title is eight hours.
Note on playback operations of DVD VIDEOs/
VIDEO CDs
VIDEO CDs
Some playback operations of DVD VIDEOs/
VIDEO CDs may be intentionally set by software
producers. Since this recorder plays DVD
VIDEOs/VIDEO CDs according to the disc
contents the software producers designed, some
playback features may not be available. Also, see
the instructions supplied with the DVD VIDEOs/
VIDEO CDs.
VIDEO CDs may be intentionally set by software
producers. Since this recorder plays DVD
VIDEOs/VIDEO CDs according to the disc
contents the software producers designed, some
playback features may not be available. Also, see
the instructions supplied with the DVD VIDEOs/
VIDEO CDs.
Region code (DVD VIDEO only)
Your recorder has a region code printed on the rear
of the unit and will only play DVD VIDEOs
(playback only) labelled with identical region
codes. This system is used to protect copyrights.
DVD VIDEOs labelled
of the unit and will only play DVD VIDEOs
(playback only) labelled with identical region
codes. This system is used to protect copyrights.
DVD VIDEOs labelled
will also play on this
recorder.
If you try to play any other DVD VIDEO, the
message “Playback prohibited by region code.”
will appear on the TV screen. Depending on the
DVD VIDEO, no region code indication may be
labelled even though playing the DVD VIDEO is
prohibited by area restrictions.
If you try to play any other DVD VIDEO, the
message “Playback prohibited by region code.”
will appear on the TV screen. Depending on the
DVD VIDEO, no region code indication may be
labelled even though playing the DVD VIDEO is
prohibited by area restrictions.
Music discs encoded with copyright protection
technologies
technologies
This product is designed to play back discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are being
marketed by some record companies. Please be
aware that among those discs, there are some that
do not conform to the CD standard and may not be
playable by this product.
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are being
marketed by some record companies. Please be
aware that among those discs, there are some that
do not conform to the CD standard and may not be
playable by this product.
Note on DualDiscs
A DualDisc is a two sided disc product which
mates DVD recorded material on one side with
digital audio material on the other side.
However, since the audio material side does not
conform to the Compact Disc (CD) standard,
playback on this product is not guaranteed.
mates DVD recorded material on one side with
digital audio material on the other side.
However, since the audio material side does not
conform to the Compact Disc (CD) standard,
playback on this product is not guaranteed.
Notes
• Some DVD+RWs/DVD+Rs, DVD-RWs/DVD-Rs, or
CD-RWs/CD-Rs cannot be played on this recorder due
to the recording quality or physical condition of the
disc, or the characteristics of the recording device and
authoring software. The disc will not play if it has not
been correctly finalized. For more information, see the
operating instructions for the recording device.
to the recording quality or physical condition of the
disc, or the characteristics of the recording device and
authoring software. The disc will not play if it has not
been correctly finalized. For more information, see the
operating instructions for the recording device.
• You cannot mix VR mode and Video mode on the same
DVD-RW. To change the disc’s format, reformat the
disc. Note that the disc’s contents will be erased after
reformatting.
disc. Note that the disc’s contents will be erased after
reformatting.
• You cannot shorten the time required for recording
even with high-speed discs.
• It is recommended that you use discs with “For Video”
printed on their packaging.
• You cannot add new recordings to DVD+Rs, DVD-Rs,
or DVD-RWs (Video mode) that contain recordings
made on other DVD equipment.
made on other DVD equipment.
• In some cases, you may not be able to add new
recordings to DVD+RWs that contain recordings made
on other DVD equipment. If you do add a new
recording, note that this recorder will rewrite the DVD
menu.
on other DVD equipment. If you do add a new
recording, note that this recorder will rewrite the DVD
menu.
• You cannot edit recordings on DVD+RWs, DVD-RWs
(Video mode), DVD+Rs, or DVD-Rs that are made on
other DVD equipment.
other DVD equipment.
• If the disc contains PC data unrecognizable by this
recorder, the data may be erased.
• You may not be able to record on some recordable
discs, depending on the disc.
Disc
Number of titles*
HDD
300
DVD-RW/DVD-R
99
DVD+RW/DVD+R
49
DVD+R DL
49
ALL
HCD–RHXXXX
MODEL NO.
DVD RECORDER
NO.
X
Region code
7
HCD-RH1000/RH7000
SECTION 2
GENERAL
This section is extracted from
instruction manual.
instruction manual.
DVD recorder
A [/1 (on/standby) button
B TIMER REC indicator
SYNCHRO REC indicator
C HDD button/indicator
D DVD button/indicator
E FM/AM button/indicator
F Disc tray
G z REC button
X REC PAUSE button
x REC STOP button
x REC STOP button
H A (open/close) button
I H (play) button
X (pause) button
x (stop) button
x (stop) button
J VOLUME +/– buttons
K
(remote sensor)
L LINE 2 IN (S VIDEO/VIDEO/AUDIO L/
R) jacks
M ./> (previous/next) buttons
N PROGRAM +/– buttons
O INPUT SELECT button
P REC MODE button
Q Front panel display
S-VIDEO
LINE 2 IN
REC STOP
REC PAUSE
REC
SYNCRO REC
TIMER REC
- PROGRAM +
INPUT
SELECT
REC
MODE
FM/AM
DVD
HDD
VIDEO
L(MONO) AUDIO R
- VOLUME +
Pull open
Rear panel
A AERIAL IN/OUT jacks
B LINE 1 – TV jack
C LINE 3/DECODER jack
D COMPONENT VIDEO OUT (Y, P
B
/C
B
,
P
R
/C
R
) jacks
E AC IN terminal
F LINE OUT (S VIDEO) jack
G LINE OUT (R-AUDIO-L/VIDEO) jacks
H LINE 4 IN (S VIDEO) jack
I LINE 4 IN (R-AUDIO-L/VIDEO) jacks
J SYSTEM CONNECTOR jack
AERIAL
IN
LINE 4 IN
COMPONENT
VIDEO OUT
VIDEO
S VIDEO
R-AUDIO-L
SYSTEM CONNECTOR
LINE OUT
VIDEO
S VIDEO
R-AUDIO-L
PB / CB
Y
PR / CR
~
AC IN
OUT
LINE 1 - TV
LINE 3/
DECODER
Front panel display
A HDD/DVD indicators
Displays the selected media and the
playing/recording/dubbing status or
direction.
playing/recording/dubbing status or
direction.
B Disc type*/recording format
C PROGRE (progressive) indicator
D SMARTLINK indicator
E Radio reception indicators (ST (stereo)/
MONO (monaural)/TUNED)
F
(angle) indicator
G Audio signal indicators
H TV indicator
I Displays the following:
• Playing time/remaining time
• Current title/chapter/track/index number
• Recording time/recording mode
• Clock
• Programme position
• TV Direct Rec indication: “TV”
• Current title/chapter/track/index number
• Recording time/recording mode
• Clock
• Programme position
• TV Direct Rec indication: “TV”
appears in the right most two digits.
• Radio station/frequency
• Sound Field
• Function name (HDD/DVD/FM/AM)
• Sound Field
• Function name (HDD/DVD/FM/AM)
J DSGX indicator
DCS indicator
Dolby Pro Logic II indicator
Dolby Pro Logic II indicator
K NICAM indicator
* Displays DATA CDs as “CD.”
z
Hint
You can turn off the front panel display when the recorder is turned off by setting “Dimmer” to “Power Save” in
“Options” setup.
“Options” setup.
HDD
DVD
DVD
VR
PROGRE
SMARTLINK
VCD
MONO
ST
TV
RW
TUNED
CH
NICAM
DSGX
DSGX
PL
DCS
Remote
A TV/DVD switch
B Z (open/close) button
C HDD button
DVD button
D Number buttons
SET button
The number 5 button has a tactile dot
*
.
E CLEAR/-/-- (ten digit) button
F
(audio) button
(subtitle) button
The
button has a tactile dot*.
G TIMER button
H SYSTEM MENU button
TITLE LIST button
TIMER LIST button
TIMER LIST button
I TOP MENU button
J </M/m/,/ENTER button
K O RETURN button
L
(instant replay)/
(instant advance)
buttons
M ./> (previous/next) buttons,
PRESET +/– buttons
N mc
/
CM (search) buttons
O VISUAL SEARCH button
P z REC button
X REC PAUSE button
x REC STOP button
x REC STOP button
Q REC MODE button
R SYNCHRO REC button
S PROGRESSIVE button
T
(wide mode) button
U [/1 (on/standby) button
V FM/AM button
1
2
3
4
6
7
8
9
0
5
Open the
cover
cover
W PROG (programme) +/– buttons
The + button has a tactile dot
*
.
X INPUT SELECT button
Y t TV/DVD button
Z DSGX button
wj SOUND FIELD +/– buttons
wk DISPLAY button
TIME/TEXT button
wl MUTING button
e; MENU button
ea
2
(volume) +/– buttons
The + button has a tactile dot
*
.
es TOOLS button
ed
H (play) button
X (pause) button
x (stop) button
X (pause) button
x (stop) button
The H button has a tactile dot*.
ef CHAPTER MARK/CHAPTER MARK
ERASE buttons
eg
(angle) button
eh FM/AM MEMORY button
ej FM MODE button
* Use the tactile dot as a reference when operating the
system.
•
Location of Controls
HCD-RH1000/RH7000
8
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
SECTION 3
DISASSEMBLY
3-2. TOP PANEL ASSY
(Page 9)
3-3. LOADING PANEL ASSY
(Page 9)
3-4. RD-053AU BOARD
(Page 10)
3-5. HDD ASSY
(Page 10)
3-6. POWER SUPPLY BLOCK
(Page 11)
3-7. ER-036AU BOARD
(Page 11)
3-8. FR-001AU BOARD, FL-001AU BOARD
(Page 12)
3-9. DVD DRIVE ASSY
(Page 12)
3-10. AV-089AU BOARD
(Page 13)
SET
Click on the first or last page to see other DAR-RH1000 / DAR-RH7000 / HCD-RH1000 / HCD-RH7000 service manuals if exist.