Sony CMT-G2BNIP / CMT-G2NIP / HCD-G2BNIP / HCD-G2NIP Service Manual ▷ View online
HCD-G2BNiP/G2NiP
9
WIRE SETTING
front side
coating clip
MAIN board
MAIN board
NET board
AMP board
coating clip
tape
tape
Note 4: Tie into the uncovered
portion of the LAN wire.
40 mm
wireless LAN module
(MOD1)
(MOD1)
coating clip
NET board
MAIN board
holder
(BREDGECO)
(BREDGECO)
wireless LAN module (MOD1)
tape
ferrite core
binding band (taiton)
LAN board
flexible flat cable
(9 core)
tape
(9 core)
tape
tape
TUNER board block
2.4 GHz antenna wire
LAN wire
50 mm
Note 3: Power transfomer wire and
AC inlet wire must not cross.
SUB-PT board
Note 2: Put the wire under the
SUB-PT
SUB-PT
board.
lead pin
lead pin
lead pin
SUB-PT board
Note 1: flexible flat cable
must not touch a
screw.
– Top view –
HCD-G2BNiP/G2NiP
10
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
SET
2-5. PANEL (FRONT) BLOCK
(Page
(Page
13)
2-9. HOLDER (CD FRONT) BLOCK
(Page
(Page
16)
2-18. DCDC BOARD
(Page
(Page
22)
2-13. CD MECHANISM DECK BLOCK
(CDM77B-K6BD94DC)
(Page
(CDM77B-K6BD94DC)
(Page
20)
2-17. HOLDER (CD) BLOCK
(Page
(Page
22)
2-15. BASE UNIT
(BU-K6BD94DC)
(Page
(BU-K6BD94DC)
(Page
21)
2-16. OPTICAL PICK-UP BLOCK
(KSM-213DCP)
(Page
(KSM-213DCP)
(Page
21)
2-2. CASE
BLOCK
(Page
11)
2-7. MAIN
BOARD
(Page
15)
2-3. WIRELESS
LAN
MODULE
(MOD1)
(Page
11)
2-8. NET
BOARD
(Page
16)
2-12. POWER TRANSFORMER
(T901)
(Page
(T901)
(Page
19)
2-10. AMP BOARD BLOCK
(Page
(Page
17)
2-11. AMP BOARD
(Page
(Page
18)
2-14. BELT
(Page
(Page
20)
2-6. PANEL (REAR) BLOCK
(Page
(Page
14)
2-4. PANEL (CD TRAY)
(Page
(Page
12)
HCD-G2BNiP/G2NiP
11
Note: Follow the disassembly procedure in the numerical order given.
2-2. CASE BLOCK
1
four screws
(BV/ring)
2
flat head screw
(TP)
2
flat head screw
(TP)
6
case block
5
two claws
3
4
3
1
two screws
(BVTP2.6)
6
screw
(BVTP2.6)
8
wireless LAN module
(MOD1)
4
2.4 GHz antenna connector
5
connector
(CN5004)
2
coating clip
3
holder (BREDGECO)
7
connector (CN5003)
Note
2: When installing the wireless LAN module,
check that there are no foreign substances,
such as dust, in the contacting part.
– Rear side view –
wireless LAN module
(MOD1)
(MOD1)
OK
NG
NG
Note 3: There are two terminals for antenna
wire in a module.
When connecting the antenna wire,
connect with the right terminal.
2-3. WIRELESS LAN MODULE (MOD1)
Note 1: Refer to “WIRE SETTING”
on page 9 for wire setting.
HCD-G2BNiP/G2NiP
12
2-4. PANEL (CD TRAY)
4
two claws
5
panel (CD tray)
6 cm or more
– Rear bottom view –
Note: There is a possibility of damaged of the panel (CD tray) when the
panel (front) block is removed without removing the panel (CD tray).
Remove panel (CD tray) earlier than removing the panel (front) block.
3
hole
lever
1
Insert the hard metal fittings of L character type 6 cm
or more in the hole of the chassis.
2
Push the lever in
the direction of
the
arrow
A.
– Bottom view –
A
Click on the first or last page to see other CMT-G2BNIP / CMT-G2NIP / HCD-G2BNIP / HCD-G2NIP service manuals if exist.