Sony CMT-G2BNIP / CMT-G2NIP / HCD-G2BNIP / HCD-G2NIP Service Manual ▷ View online
HCD-G2BNiP/G2NiP
13
2-5. PANEL (FRONT) BLOCK
– Rear side view –
1
Lift up two
coating
clips.
4
Lift up the coating clip.
5
Turn over the flexible
flat cable (15 core).
2
connector (CN805)
3
connector
(CN601)
6
flexible flat cable (19 core)
(CN404)
7
two screws
(BV3)
0
claw
0
claw
9
two screws
(BV/ring)
qa
panel (front) block
8
screw
(BVTP3
u 8)
8
screw
(BVTP3
u 8)
Insert is straight to the interior
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
Note 4: When you install the flexible flat cable, please install them
correctly.
correctly.
There is a possibility that this machine damages when not
correctly installing it.
Note 1: There is a possibility of damaged of the panel (CD tray) when the
panel (front) block is removed without removing the panel (CD tray).
Remove panel (CD tray) earlier than removing the panel (front) block.
Note 5: Refer to “WIRE SETTING” on page 9 for the setting of those other than this.
– Front panel inner view –
front side
sleeve ferrite clamp
HP board
USB board
JOG2 board
tape
The wire must be on the
sleeve ferrite clamp.
sleeve ferrite clamp.
The sleeve ferrite clamp must
come under the USB board.
come under the USB board.
:ire settinJ
holder (CD)
CD mechanism deck
cover (CD top)
Note 2: When you install the panel (front) block,
put two sleeve ferrite clamps within this
dotted line range.
Note 3: Confirm the BD94DC board has not dropped.
HCD-G2BNiP/G2NiP
14
2-6. PANEL (REAR) BLOCK
Note 1: Refer to “WIRE SETTING” on page 9 for wire setting.
2
coating clip
1
two screws
(BVTP2.6)
– Rear side view –
(G2BNiP)
Insert is straight to the interior
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
Note 2: When you install the flexible flat cable, please install them
correctly. There is a possibility that this machine damages
when not correctly installing it.
3
holder (BREDGECO)
5
2.4 GHz antenna
connector
6
connector
(CN5004)
7
connector
(CN701)
8
connector
(CN4404)
4
Lift up the lead pin.
9
connector
(CN4405)
0
flexible flat cable (9 core) (CN407)
Note
4: Both the flexible flat cable (9 core) can be connected with
the CN406 or CN407 on MAIN board.
When you connect the flexible flat cable (9 core) with the
CN407 on MAIN board so as not to connect it by mistake.
qa
flexible flat cable (8 core) (CN408)
CN406
qs
two screws
(BV/ring)
qf
screw
(BV3)
qg
coating clip
coating clip
AC inlet
qh
panel (rear) block
qs
three screws
(BV/ring)
qd
– Rear side view –
Clamp tilter (ferrite core) setting
clamp tilter (ferrite core)
55 mm
rear side
wireless LAN module
(MOD1)
(MOD1)
OK
NG
NG
Note 3: There are two terminals for antenna wire in a module.
When connecting the antenna wire, connect with the
right
terminal.
HCD-G2BNiP/G2NiP
15
2-7. MAIN BOARD
Note 1: Refer to “WIRE SETTING” on page 9 for wire setting.
qd
three screws
(BVTP3
u 8)
qd
two screws
(BVTP3
u 8)
qf
two coating clips
qg
MAIN board
6
flexible flat cable (15 core)
(CN403)
5
connector
(CN702)
0
connector
(CN805)
9
connector
(CN601)
2
connector
(CN701)
3
connector
(CN803)
7
flexible flat cable (19 core)
(CN404)
1
Lift up the coating clip.
1
Lift up the coating clip.
1
Lift up the coating clip.
A
A
B
CN406
qa
flexible flat cable (9 core) (CN407)
Note
4: Both the flexible flat cable (9 core) can be
connected with the CN406 or CN407 on
MAIN board. When you connect the flexible
flat cable (9 core) with the CN407 on MAIN
board so as not to connect it by mistake.
4
flexible flat cable (21 core) (CN401)
Note
2: Both the flexible flat cable (21 core) can be
connected with the CN401 or CN402 on
MAIN board. When you connect the flexible
flat cable (21 core) with the CN401 on MAIN
board so as not to connect it by mistake.
8
flexible flat cable (21 core) (CN402)
Note
3: Both the flexible flat cable (21 core) can be
connected with the CN401 or CN402 on
MAIN board. When you connect the flexible
flat cable (21 core) with the CN402 on MAIN
board so as not to connect it by mistake.
Insert is straight to the interior
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
Note 5: When you install the flexible
flat cable, please install them
correctly.
There is a possibility that this
machine damages when not
correctly installing it.
B
(G2BNiP)
qs
flexible flat cable (8 core) (CN408)
HCD-G2BNiP/G2NiP
16
2-8. NET BOARD
2-9. HOLDER (CD FRONT) BLOCK
2
two screws
(BVTP3
u 8)
2
two screws
(BVTP3
u 8)
3
NET board
1
flexible flat cable (21 core)
(CN5005)
Insert is straight to the interior
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
Note: When you install the flexible flat cable, please install them
correctly. There is a possibility that this machine damages
when not correctly installing it.
3
screw
(BVTP3
u 8)
1
screw
(BVTP3
u 8)
1
screw
(BVTP3
u 8)
3
two screws
(BVTP3
u 8)
4
two screws
(BV3)
2
cover (CD front)
6
holder (CD front) block
5
claw
5
two claws
– Left front side view –
Click on the first or last page to see other CMT-G2BNIP / CMT-G2NIP / HCD-G2BNIP / HCD-G2NIP service manuals if exist.