Sony CMT-G2BNIP / CMT-G2NIP / HCD-G2BNIP / HCD-G2NIP Service Manual ▷ View online
HCD-G2BNiP/G2NiP
17
2-10. AMP BOARD BLOCK
lead pin
AMP board
:LUHVHWWLQJ
front side
Insert is straight to the interior
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
Note: When you install the flexible flat cable, please install them
correctly. There is a possibility that this machine damages
when not correctly installing it.
–5HDUVLGHYLHZ–
2
Lift up the lead pin.
4
screw (BV3)
5
lug wire
6
AMP board block
4
two screw
(BV3)
1
flexible flat cable (5 core)
(CN103)
3
connector
(CN301)
HCD-G2BNiP/G2NiP
18
2-11. AMP BOARD
1
screw
(BVTP3
u 8)
3
screw
(BVTP3
u 8)
A
A
2
plate (earth AMP)
6
shield R plate (AMP)
4
holder (PWB AMP)
qj
AMP board
3
screw
(BVTP3
u 8)
5
two screws
(BVTP3
u 8)
5
screw
(BVTP3
u 8)
qs
two screws
(BVTP3
u 8)
7
two screws
(BVTP3
u 8)
8
shield L plate (AMP)
qd
heat-sink
qf
sheet (radiation)
9
Lift up two lead pins.
0
clamp filter (ferrite core)
qa
sleeve ferrite
clamp
qg
flexible flat cable (15 core)
(CN102)
flexible flat cable (15 core)
qh
ferrite core block
:LUHVHWWLQJ
)OH[LEOHIODWFDEOHFRUHVHWWLQJ
lead pin
R2117
tape
lead pin
front side
Roll the wire once.
Roll the wire
once.
once.
clamp filter
(ferrite core)
(ferrite core)
sleeve ferrite clamp
–5HDUVLGHYLHZ–
35 mm
ferrite core block
Insert is straight to the interior
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
Note 1: When you install the flexible flat cable, please install them
correctly. There is a possibility that this machine damages
when not correctly installing it.
Note 2: Fix so that a wire
cannot touch R2117.
Less than
30 mm
30 mm
Roll the wire
once.
once.
HCD-G2BNiP/G2NiP
19
2-12. POWER TRANSFORMER (T901)
1
Lift up the lead pin.
9
clamp filter (ferrite core)
0
power transformer
(T901)
9
clamp filter
(ferrite
core)
4
Lift up the lead pin.
3
Remove the coating clip from
the clamp filter (ferrite core).
2
connector
(CN301)
5
connector
(CN952)
6
four screws
(BVTT4
u 8)
8
plate (trans)
7
front side
– Top view –
Roll the wire once.
tape
tape
tape
clamp filter
(ferrite core)
(ferrite core)
holder (CD)
:iUe VeWWiQJ
Note: Confirm the wire does not
hit the edge of holder (CD).
lead pin
DCDC board
rear side
100 mm
100 mm
30 mm
150 mm
power transformer (T901)
clamp filter
(ferrite core)
(ferrite core)
coating clip
clamp filter
(ferrite core)
(ferrite core)
lead pin
AMP board
front side
tape
coating clip
clamp filter
(ferrite core)
(ferrite core)
– 5eDU ViGe view –
HCD-G2BNiP/G2NiP
20
2-13. CD MECHANISM DECK BLOCK (CDM77B-K6BD94DC)
2-14. BELT
6
flexible flat cable
(21
core)
(CN202)
9
CD mechanism deck block
(CDM77B-K6BD94DC)
5
flexible flat
cable (5 core)
flexible flat cable
(5 core)
(5 core)
flexible flat cable
(21 core)
(21 core)
2
connector
(CN103)
1
cover (CD top)
4
3
three screws
(BVTP3
u 8)
7
Remove the
solder.
8
CD sheet
20 mm
10 mm
MOTOR board
BD94DC
board
board
tape
tape
)OH[LEOHIODWFDEOHVHWWLQJ
±&'PHFKDQLVPERWWRPYLHZ±
rear side
Insert is straight to the interior
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
Note: When you install the flexible flat cable, please install them
correctly. There is a possibility that this machine damages
when not correctly installing it.
5
belt
3
claw
3
claw
2
A
4
tray (AU)
belt
3RVLWLRQRIEHOW
1
Push the lever in the direction
of the arrow
A.
±&'PHFKDQLVPERWWRPYLHZ±
Click on the first or last page to see other CMT-G2BNIP / CMT-G2NIP / HCD-G2BNIP / HCD-G2NIP service manuals if exist.