Sony BDV-L600 / BDV-L800 / BDV-L800M / HBD-L600 / HBD-L800 / HBD-L800M Service Manual ▷ View online
HBD-L600/L800/L800M
9
CHECKING METHOD OF NETWORK OPERATION
It is necessary to check the network operation, when replacing the
MB-141 board or wireless LAN card (HBD-L800/L800M only).
Check the operation of wireless and wired LAN, according to the
following method.
It is necessary to check the network operation, when replacing the
MB-141 board or wireless LAN card (HBD-L800/L800M only).
Check the operation of wireless and wired LAN, according to the
following method.
1. Checking Method of Wireless LAN Operation (HBD-
L800/L800M only)
Check that access point is recognized surely.
Necessary Equipment:
Wireless access point with router function (AP)
Wireless access point with router function (AP)
Procedure:
1. Press the [HOME] button on the remote commander to enter
1. Press the [HOME] button on the remote commander to enter
the home menu.
2. Press the [
m]/[M]/[<]/[,] buttons on the remote command-
er to select “Network Settings”
“Internet Settings”, and press
the [
] button on the remote commander.
3. Press the [
m]/[M] buttons on the remote commander to select
“Wireless Setup (built-in)”, and press the [
] button on the
remote commander.
4. Press the [
m]/[M] buttons on the remote commander to select
“Scan”, and press the [
] button on the remote commander.
5. The system starts searching for access points, and displays a
list of up available network name (SSID).
6. Check that access point (SSID) is displayed on the searching
result.
Note: Refer to the instruction manual about details of the setting method.
2. Checking method of wired LAN operation
Check that access point is recognized surely.
Check that access point is recognized surely.
Procedure:
1. Connect the main unit to the router or the hub, etc. with the
1. Connect the main unit to the router or the hub, etc. with the
LAN cable.
2. Press the [HOME] button on the remote commander to enter
the home menu.
3. Press the [
m]/[M]/[<]/[,] buttons on the remote command-
er to select “Network Settings”
“Internet Settings”, and press
the [
] button on the remote commander.
4. Press the [
m]/[M] buttons on the remote commander to select
“Wired Setup”, and press the [
] button on the remote com-
mander.
5. Press the [
m]/[M]/[<]/[,] buttons on the remote command-
er to select “Auto”, and press the [
] button on the remote
commander.
6. Press the [
,] button on the remote commander.
7. Press the [
m]/[M] buttons on the remote commander to select
“Save & Connect”, and press the [
] button on the remote
commander.
8. When “Internet Settings is now complete.” appears, then press
the [
] button on the remote commander.
9. Press the [HOME] button on the remote commander to enter
the home menu.
10. Press the [
m]/[M]/[<]/[,] buttons on the remote command-
er to select “Network Settings”, and press the [
] button on
the remote commander.
11. Press the [
m]/[M] buttons on the remote commander to select
“Network Connection Diagnostics”, and press the [
] button
on the remote commander.
12. Press the [
<]/[,] buttons on the remote commander to
select “Start”, and press the [
] button on the remote com-
mander.
13. Check that IP address can be acquired.
Note: Refer to the instruction manual about details of the setting method.
HBD-L600/L800/L800M
10
HOW TO EJECT THE DISC WHEN POWER SWITCH TURN OFF
Note 1: After the rear cover is removed, this work is done.
Note 2: Please prepare the JIG connector (Part No. 1-770-638-11 FFC connector/FPC 7P).
Note 3: Operate by setting up the BD drive without fail in the vertical direction.
Note 2: Please prepare the JIG connector (Part No. 1-770-638-11 FFC connector/FPC 7P).
Note 3: Operate by setting up the BD drive without fail in the vertical direction.
BD DRIVE SERVICE POSITION
REGULATED
DC POWER
SUPPLY
DC POWER
SUPPLY
2 pin
1 pin
Connect JIG connector to wire (flat type) (7 core)
that removes CN2490 of MB-141 board.
that removes CN2490 of MB-141 board.
Refer to below figure and supply DC5V to 1 pin and 2 pin.
JIG connector
CN2490
Note 4: 3 – 7 pin are cut beforehand before it installs connector.
MB-141 board
BD drive (BSX-2)
Note: Operate by setting up the BD drive
Note: Operate by setting up the BD drive
without fail in the vertical direction.
HBD-L600/L800/L800M
11
SECTION 2
DISASSEMBLY
•
This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
Note: Follow the disassembly procedure in the numerical order given.
2-2. STAND
ASSY
SET
2-3. PLATE TOP BLOCK
(Page
(Page
12)
2-4. FL
BOARD
(Page
13)
2-9. COVER BOTTOM BLOCK
(Page
(Page
15)
2-13. BRACKET (CHASSIS) BLOCK
(Page
(Page
17)
2-14. MB-141 BOARD
(Page
(Page
18)
2-15. DC FAN (M1)
(Page
(Page
19)
2-10. USB BOARD
(Page
(Page
16)
2-11. TUNER BOARD BLOCK
(Page
(Page
16)
2-7. HAMON
BLOCK
(Page
14)
2-8. COVER (TOP) BLOCK
(Page
(Page
15)
2-5. WIRELESS LAN CARD (WLC1) (HBD-L800/L800M)
(Page
(Page
13)
2-6. PWR_KEY
BOARD
(Page
14)
2-12. CONNECT BOARD
(Page
(Page
17)
2-16. BD DRIVE (BSX-2)
(Page
(Page
19)
2-2. STAND
ASSY
(Page
11)
2-17. BOTTOM COVER
(Page
(Page
20)
2-18. OPTICAL PICK-UP
(KEM-470AAA)
(Page
(KEM-470AAA)
(Page
21)
2-19. HOW TO BEND FFC
(Page
(Page
22)
1 four screws
(wall)
2 stand assy
– Rear top view –
Note: Please spread a sheet
under a unit not to injure
plate
(top).
HBD-L600/L800/L800M
12
2-3. PLATE TOP BLOCK
3 four screws
(BV2.6
u 8)
– Rear bottom (left) view –
– Front bottom view –
– Front bottom view –
1
2 lid bottom assy
3 five screws
(BV2.6
u 8)
5 three claws
6
5 four claws
4 six claws
Note 1: Please spread a sheet
under a unit not to injure
plate
(top).
8 five claws
9 plate (top) block
coloured line
connector
7 wire (flat type) (9 core)
(CN248)
terminal face
flat cable
Note 2: When you install the flat cable,
ensure the coloured line.
No slanting after insertion.
Click on the first or last page to see other BDV-L600 / BDV-L800 / BDV-L800M / HBD-L600 / HBD-L800 / HBD-L800M service manuals if exist.