Sony BDV-L600 / BDV-L800 / BDV-L800M / HBD-L600 / HBD-L800 / HBD-L800M Service Manual ▷ View online
HBD-L600/L800/L800M
21
2-18. OPTICAL PICK-UP (KEM-470AAA)
1 two float screws (S)
1 two float screws (S)
6 optical pick-up
(KEM-470AAA)
5 insulator
5 insulator
5 insulator
5 insulator
2
3 flexible flat cable (45 core)
4 flexible flat cable (9 pin)
– BD drive bottom view –
coloured line
connector
flat cable
Note: When you install the flat cable,
ensure the coloured line.
No slanting after insertion.
HBD-L600/L800/L800M
22
2-19. HOW TO BEND FFC
ZLUHIODWW\SHFRUHOHQJWKPP5HI1R
ZLUHIODWW\SHFRUHOHQJWKPP5HI1R
98 mm
72 mm
125 mm
CONNECT board
(CN248)
CONNECT board
(CN241)
MB-141 board
(CN6201)
MB-141 board
(CN5908)
WS_P board
(CN1002)
The upper side
is terminal side.
is terminal side.
The upper side
is terminal side.
is terminal side.
ZLUHIODWW\SHFRUHOHQJWKPP5HI1R
ZLUHIODWW\SHFRUHOHQJWKPP5HI1R
IOH[LEOHIODWFDEOHFRUHOHQJWKPP5HI1R
//0
//0
IOH[LEOHIODWFDEOHFRUHOHQJWKPP5HI1R
IOH[LEOHIODWFDEOHSLQOHQJWKPP5HI1R
IOH[LEOHIODWFDEOHSLQOHQJWKPP5HI1R
45 mm
CONNECT board
(CN245)
The upper side
is terminal side.
is terminal side.
TOUCH board
(CN202)
HAMON LED board
(CN801)
The lower side
is terminal side.
is terminal side.
The lower side
is terminal side.
is terminal side.
The lower side
is terminal side.
is terminal side.
: Mountain fold
: Valley fold
: Valley fold
6 mm
52 mm
25 mm
12 mm
8 mm
8 mm
18 mm
18 mm
37 mm
38 mm
The lower side
is terminal side.
is terminal side.
The lower side
is terminal side.
is terminal side.
The lower side
is terminal side.
is terminal side.
The upper side
is terminal side.
is terminal side.
MB-141 board
(CN5906)
MB-141 board
(CN1301)
CONNECT board
(CN242)
5 mm
13 mm
67 mm
65 mm
The upper side
is terminal side.
is terminal side.
The upper side
is terminal side.
is terminal side.
BD drive
(BSX-2)
183 mm
79 mm
15 mm
23 mm
MB-141 board
(CN2460)
The lower side
is terminal side.
is terminal side.
MB-141 board
(CN2460)
156 mm
14 mm
11 mm
75 mm
14 mm
BD drive
(BSX-2)
The lower side
is terminal side.
is terminal side.
9 mm
29 mm
117 mm
94 mm
101 mm
MB-141 board
(CN2490)
The lower side
is terminal side.
is terminal side.
BD drive
(BSX-2)
The lower side
is terminal side.
is terminal side.
HBD-L600/L800/L800M
23
SECTION 3
TEST MODE
COLD RESET
The cold reset clears data except BD/DVD data stored in the RAM
to initial conditions. Execute this mode when returning the unit to
the customers.
Procedure:
1. Press the [
The cold reset clears data except BD/DVD data stored in the RAM
to initial conditions. Execute this mode when returning the unit to
the customers.
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Touch the [
x
] and [VOL –] sensors simultaneously and hold
down (around 5 seconds).
3. The message “RESET” appears on fl uorescent indicator tube,
then becomes standby states.
DEMO MODE
This mode let you lock the disc tray. When this mode is activated,
the disc will not eject when the [
This mode let you lock the disc tray. When this mode is activated,
the disc will not eject when the [
Z
] sensor is touched. The mes-
sage “DEMO LOCK” will be displayed on the fluorescent indica-
tor tube.
Procedure:
1. Press the [
tor tube.
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Touch the [FUNCTION] sensor to select the “BD/DVD”.
3. Touch the [
3. Touch the [
x
] and [
Z
] sensors simultaneously and hold down
until “DEMO LOCK” or “DEMO OFF” displayed on the fluo-
rescent indicator tube (around 5 seconds).
rescent indicator tube (around 5 seconds).
Releasing method:
Touch the [
Touch the [
x
] and [
Z
] sensors simultaneously and hold down until
“DEMO OFF” displayed on the fl uorescent indicator tube (arround
5 seconds).
5 seconds).
PANEL TEST
Procedure:
1. Press the [
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press button in order of the [DISPLAY]
[0] [0] [1]
[SUBTITLE] on the remote commander (Make the interval
when each button is pressed within two seconds).
when each button is pressed within two seconds).
3. All
segments
in
fl uorescent indicator tube are lighted up. And
half segments in fl uorescent indicator tube are lighted up, oth-
ers half segments in fl uorescent indicator tube are lighted up,
then all segments in fl uorescent indicator tube are lighted up.
This operation is repeated.
ers half segments in fl uorescent indicator tube are lighted up,
then all segments in fl uorescent indicator tube are lighted up.
This operation is repeated.
4. When all segments in fl uorescent indicator tube are lighted up
in the state of step 3, press the [VOL +] button on the remote
commander and model information is displayed on the fl uores-
cent indicator tube.
commander and model information is displayed on the fl uores-
cent indicator tube.
Each time the [VOL +] button on the remote commander is
pressed, the display changes from destination information,
STR version in this order, and returns to the model informa-
tion display.
pressed, the display changes from destination information,
STR version in this order, and returns to the model informa-
tion display.
Each time the [VOL –] button on the remote commander is
pressed, the version and date are switched.
pressed, the version and date are switched.
5. In the state of step 3, press the [FUNCTION] button on the
remote commander and “K 0” is displayed on the fluorescent
indicator tube.
indicator tube.
“K 0” value increases whenever a button or sensor on the unit
is pressed. However, once a button or sensor has been pressed,
it is no longed taken into account.
is pressed. However, once a button or sensor has been pressed,
it is no longed taken into account.
All button and sensors on the unit are pressed, “OK” and “K 7”
are alternately displayed on the fluorescent indicator tube.
are alternately displayed on the fluorescent indicator tube.
Releasing method:
To release from this mode, press the [
To release from this mode, press the [
?/1
] button.
FACTORY INITIALIZE
Return all of the unit setting to their factory defaults.
Return all of the unit setting to their factory defaults.
Note 1: Disconnect the following connections when you use this mode.
Left USB
Rear USB
LAN
HDMI IN 1
HDMI IN 2
Note 2: The operation in this mode must use a remote commander and TV
monitor.
Procedure:
1. Press the [
1. Press the [
?/1
] button to turn the power on.
2. Press the [HOME] button on the remote commander, and the
home menu is displayed.
3. Select
“Setup”
“Resetting”, and press the [ ] button on the
remote commander.
Resetting
Easy Setup
4. Select “Initialize Personal Information”, and press the [
]
button on the remote commander.
Initialize Personal Information
Erase personal data when disposing
Erase personal data when disposing
Reset to Factory Default Settings
5. Select “OK”, and press the [
] button on the remote com-
mander.
Initialize Personal Information
OK
Cancel
The information below will be deleted.
Do you want to proceed?
Playback history
Internet video utilization information
Internet content registered as Favorites
Do you want to proceed?
Playback history
Internet video utilization information
Internet content registered as Favorites
HBD-L600/L800/L800M
24
BD SERVICE MODE
[Wireless checking fail on M07.R.179]
Due to software bug in M07.R.179, currently Service mode do not sup-
port wireless checking features this version of software.
For service to confi rm the wireless checking, please update customer
sets to latest version of software. By using network upgrade method
or Disc upgrade method. After fi nish upgraded, Service member can
perform wireless checking as mention in wireless LAN checking pages.
Due to software bug in M07.R.179, currently Service mode do not sup-
port wireless checking features this version of software.
For service to confi rm the wireless checking, please update customer
sets to latest version of software. By using network upgrade method
or Disc upgrade method. After fi nish upgraded, Service member can
perform wireless checking as mention in wireless LAN checking pages.
Or
Confi rm wireless LAN connection from customer mode, in case of
Wireless connection successfully establish. The wireless Lan network
connection will be judge as OK.
Wireless connection successfully establish. The wireless Lan network
connection will be judge as OK.
Date: 26 January 2011
Note: The operation in this mode must use a remote commander and TV
monitor.
Setting method of the BD service mode:
1. Connect this unit with TV monitor.
2. Press the [
1. Connect this unit with TV monitor.
2. Press the [
?/1
] button to turn the power on.
3. Press button in order of the [DISPLAY]
[0] [2] [1]
[SUBTITLE] on the remote commander. (Make the interval
when each button is pressed within two seconds)
when each button is pressed within two seconds)
4. Enter the BD service mode. The OSD menu on TV monitor
can be operated by remote commander.
1. Main
Functions
• Diag
Performs unit test of devices installed on the board.
•
Display Error Log
Error log is displayed. Displayed contents can also be saved in
an USB memory device.
an USB memory device.
• Factory
Initialize
Restores the unit to its factory settings.
• Network
Checks the wired network connection.
• Version
Up
Not
used.
• System
Information
Displays the system information of the unit.
Displays information such as the software version, drive infor-
mation, etc.
mation, etc.
• EMC
Test
Mode
Not
used.
• Drive
Write drive OP data and check drive.
6. The message “Close” appears, and press the [
] button on the
remote commander.
Initialize Personal Information
Close
Initialization complete.
7. Select “Reset to Factory Default Settings”, and press the [
]
button on the remote commander.
Initialize Personal Information
Reset to Factory Default Settings
Restore each setting to the factory d
Restore each setting to the factory d
8. Select “All Settings”, and press the [
] button on the remote
commander.
Reset to Factory Default Settings
BD/DVD Viewing Settings
Personal Control Settings
Music Settings
System Settings
Network Settings
All Settings
Personal Control Settings
Music Settings
System Settings
Network Settings
All Settings
9. Select “Start”, and press the [
] button on the remote com-
mander.
All Settings
Restore all settings to the factory default
settings. The system will turn off after
reset.
settings. The system will turn off after
reset.
Start
Cancel
10. Initialization ends when the message “WELCOME” on the
fl uorescent indicator tube disappears.
Click on the first or last page to see other BDV-L600 / BDV-L800 / BDV-L800M / HBD-L600 / HBD-L800 / HBD-L800M service manuals if exist.