Sharp VC-S2000 (serv.man22) User Manual / Operation Manual ▷ View online
34
If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours)
or www.sharp.co.uk/support
SPECIAL FEATURES ON YOUR VCR
CHILD LOCK
You can lock your VCR with this feature. It will work even when the VCR is in POWERSAVE/
STANDBY, preventing children from operating the VCR.
STANDBY, preventing children from operating the VCR.
TO ENGAGE CHILD LOCK
Press and hold
on the remote control for about 2 seconds.
flashes and then
remains lit on the VCR display confirming that CHILD LOCK
has been activated.
Regardless of what other operating buttons are touched, the VCR will continue to operate in
its present mode. If CHILD LOCK is activated during playback, once the tape reaches its end,
the VCR will automatically rewind the tape, eject it, and turn the power off.
its present mode. If CHILD LOCK is activated during playback, once the tape reaches its end,
the VCR will automatically rewind the tape, eject it, and turn the power off.
TO DISENGAGE CHILD LOCK
Press and hold
for about 2 seconds.
starts flashing and then disappears. CHILD LOCK is disengaged.
NOTES:
•
If you attempt to change modes by pressing another button while CHILD LOCK is on,
the
the
indicator will flash on the VCR display.
•
If power is interrupted for more than 1 hour (due to power failure etc), CHILD LOCK may
disengage.
disengage.
TINS-3894 ENGLISH.book Page 34 Wednesday, September 6, 2000 11:53 AM
35
If problems persist contact the SHARP Helpline on tel:08705-274277 (office hours)
or www.sharp.co.uk/support
CUSTOMISED INSTALLATION
MANUALLY TUNING A CHANNEL
•
It should not be necessary to tune in a broadcast channel manually except in unusual
circumstances such as poor signal.
circumstances such as poor signal.
To manually tune in a channel follow the procedure below.
1.
Press
MENU
.
2.
Press the
/
menu select buttons
to select SET UP. Press
SET
to confirm.
3.
CHANNEL PRESET
will be
highlighted. Press
SET
.
4.
Press
/
to select
CHANNEL
.
5.
IMPORTANT NOTE:
Press
to select CH or CC. This will
determine whether off air (CH) or cable
(CC) is tuned first. Note that both off air
and cable will be tuned regardless of the
setting.
6.
Press
/
to start tuning in either
direction. Tuning will stop when a channel
is received. If it is not the desired channel,
press
/
to continue tuning.
7.
Press
/
to select
FINE
TUNING
. Press and hold
/
until
the sharpest colour picture is obtained.
IMPORTANT NOTE:
8.
If you connect an independent decoder,
you must press
/
to select
DECODER, then select
/
to turn
the decoder function ON.
9.
Press
/
to select
SKIP
.
The SKIP function determines whether the
channel can be selected when using the
CHANNEL
/
instead of the
NUMBER BUTTONS
.
10.
Press
/
to select ON or OFF for
this option.
11.
Press
SET
to confirm.
12.
Press
MENU
to leave this function.
S E T U P
C HANN E L
P R E S E T
C HANN E L S O R T
C L O C K
➔
P R E S E T
1
CHANN E L
CH 2 1
F I N E T UN I NG
▲
▲
D E COD E R
ON
O F F
S K I P
ON
O F F
CABLE RECEPTION
Station
Signals VHF
Real
Channel
Numbers
A
B
C
D
E
F
F
G
H
J
01
02
03
04
05
06
07
08
09
02
03
04
05
06
07
08
09
MENU
SET
CLEAR
PLUSCODE
TAPE SPEED SURROUND
REC
DIRECT TV REC
TINS-3894 ENGLISH.book Page 35 Wednesday, September 6, 2000 11:53 AM
36
If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours)
or www.sharp.co.uk/support
CUSTOMISED INSTALLATION
MANUALLY TUNING A CHANNEL
The VCR has 99 programmable channel positions each of which can be set to any of the
broadcast and CATV channels shown in the table. If you select CC on the menu, cable will
be tuned first. Note that both cable and non-cable will be tuned regardless of the setting.
broadcast and CATV channels shown in the table. If you select CC on the menu, cable will
be tuned first. Note that both cable and non-cable will be tuned regardless of the setting.
SATELLITE RECEIVER INSTALLATION
If you wish to connect a satellite receiver to your VCR after auto-installation without a satellite
receiver it is not necessary to completely re-install all channels. Follow the procedure below:
1.
Press
MENU
.
2.
Press [
/
] to select SET UP. Press
SET
to confirm.
3.
CHANNEL PRESET
will be
highlighted. Press
SET
to confirm.
4.
Press [
/
] to select
SAT
RECEIVER
. Press
SET
to confirm. The
satellite receiver screen will appear.
5.
Follow points
10-15
in
AUTO
INSTALLATION
(satellite/cable box
control only).
6.
Then press [
/
] to select
SAT
PROG SEARCH
. Press
SET
to confirm.
The satellite channels will be installed. (This
may take a few minutes).
7.
Then press
MENU
.
MANUAL TUN I NG
S AT RE C E I V ER
S AT PROGRAM S EARCH
MANUAL TUN I NG
S AT RE C E I V ER
S AT PROGRAM S EARCH
TINS-3894 ENGLISH.book Page 36 Wednesday, September 6, 2000 11:53 AM
37
CUSTOMISED INSTALLATION
INSTALLATION OF A SKY DIGIBOX RECEIVER
1.
Connect your Sky Digibox receiver to the VCR as shown in connecting the cables.
2.
Place the receiver near the VCR (ideally on the top). This ensures that the reflected
infrared signals from the VCR which control the satellite receiver can reach it unimpeded.
infrared signals from the VCR which control the satellite receiver can reach it unimpeded.
3.
Ensure the receiver is not in Standby or any special mode.
INSTALLATION PROCEDURE
Turn the TV on and select the video channel . (As previously explained)
1.
2.
NOTE:
•
The preset Sky channels can now be tuned in as part of the installation procedure.
•
If the AUTO INSTALLATION screen doesn’t
appear when you switch on your VCR or
you wish to reset your VCR and start the
installation again, refer to
appear when you switch on your VCR or
you wish to reset your VCR and start the
installation again, refer to
VCR RESET
at
the back of the book.
Press
STOP
to switch on the VCR.
Step through the on screen instructions by
pressing the
pressing the
SET
button.
If problems persist contact the SHARP Customer Helpline on tel: 08705-274277 (office hours)
or www.sharp.co.uk/support
See next page to continue
P L E A S E
B E
S UR E
T H E
A E R I A L / S CAR T
CAB L E I S
CONN E C T E D T O YOUR V CR .
S E T
: E N T E R ME NU : E X I T
Press the
SET
button.
Press the
SET
button.
AU T O
I N S T A L L A T I ON
P R E S S
S E T
K E Y
T O S T AR T
S E T
: E N T E R ME NU : E X I T
SUPER P.
SKIP SEARCH
MENU
SET
CLEAR
PLUSCODE
3D-DNR/TBC
TINS-3894 ENGLISH.book Page 37 Wednesday, September 6, 2000 11:53 AM
Click on the first or last page to see other VC-S2000 (serv.man22) service manuals if exist.