Sharp VC-S2000 (serv.man22) User Manual / Operation Manual ▷ View online
30
If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours)
or www.sharp.co.uk/support
ADVANCED OPERATION
REMOTE CONTROL OPERATION OF TV
In addition to operating the VCR the remote control will also operate basic functions on TVs,
including brands other than SHARP.
including brands other than SHARP.
SETTING UP THE VCR REMOTE
CONTROL TO OPERATE THE TV
CONTROL TO OPERATE THE TV
1.
Switch on the TV. Open the door on the
remote control and point the unit at the TV.
remote control and point the unit at the TV.
2.
Hold down
TV BRAND SET
on the VCR
remote control and the appropriate
button for the TV from the list shown, for 2
seconds. For example for a SHARP TV, press
button for the TV from the list shown, for 2
seconds. For example for a SHARP TV, press
TV BRAND SET
and
1
.
3.
The TV will enter standby mode to confirm
the correct code has been entered.
the correct code has been entered.
4.
To turn the TV on from standby mode hold
TV BRAND SET
and
1
(Sharp TV) for
about 2 seconds.
CONTROLLING THE TV WITH THE VCR REMOTE CONTROL
•
TV OPERATE
Switches the TV to and from Standby Mode.
•
TV INPUT SELECT
Determines which input to the TV is to be displayed on the
screen.
screen.
•
TV CH
/
Changes the TV channels.
•
TV VOL
/
Increases or decreases the volume.
•
Certain models of TV do not use standard codes for their brand. In this case hold down
TV BRAND SET
, then press each of the buttons in the list until the TV enters stand-by
mode (You will need to reset when remote control batteries are replaced).
•
SHARP cannot guarantee the VCR remote control will operate your TV.
TV BRAND
BUTTON
TV BRAND
BUTTON
SHARP
1
TOSHIBA
9
PHILIPS
2
PANASONIC
0 or
THOMSON
3 or 4
HITACHI
INPUT SELECT
GRUNDIG
5
SANYO
MODE OSD
FERGUSON
6
JVC
DISPLAY
ITT NOKIA
7
MITSUBISHI
AUDIO OUT
SONY
8
+
TINS-3894 ENGLISH.book Page 30 Wednesday, September 6, 2000 11:53 AM
31
If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours)
or www.sharp.co.uk/support
ADVANCED OPERATION
RECORDING FROM OTHER EQUIPMENT
You can record video and audio signals from various sources, for example a camcorder, onto
a video tape using your VCR.
a video tape using your VCR.
For example, recording from a camcorder connected to LINE 2 IN/DECODER on your VCR:
1.
Connect your signal source (e.g. Camcorder, Digital Camera, etc.) to the desired scart
socket on he back of the VCR using the manufacturers recommended cable (not
supplied).
socket on he back of the VCR using the manufacturers recommended cable (not
supplied).
2.
Ensure that the tape on which you
wish to record is inserted into the VCR..
wish to record is inserted into the VCR..
3.
Press
INPUT SELECT
on the remote
control until the VCR display shows
L2
.
4.
If you wish to record from a source
connected to LINE 1 IN/OUT, select
connected to LINE 1 IN/OUT, select
L1
.
5.
If you wish to record from a source
connected with audio phono leads to
the sockets on the front of the VCR
and S-VIDEO connection lead, select
connected with audio phono leads to
the sockets on the front of the VCR
and S-VIDEO connection lead, select
L3
.
6.
Press
REC
to start the recording.
NOTES:
•
There are many different ways of connecting external equipment to your VCR. Please
refer to your equipment operation manuals for further information.
refer to your equipment operation manuals for further information.
•
S-Video connection has priority over the Video connection when both are connected
to the L3 input.
to the L3 input.
•
To Record/Playback audio when connected via the S-Video input you must also
connect the audio phono leads (L3).
connect the audio phono leads (L3).
Optional SCART connection (not supplied).
Mono/Stereo Camcorder
RF OUT
SORTIE ANTENNE
ANTENNA IN
ENTREE ANTENNE
G
D
S-VIDEO OUT
SORTIE SON S-VIDEO
AUDIO
(R)
AUDIO
(L/MONO)
VIDEO
AM
PM
AM
PM
AUDIO OUT
AM/PM
LOW
ZERO BACK
INPUT SELECT
7
8
0
9
DPSS
R
SORTIE
S-VIDEO OUT
SORTIE SON S-VIDEO
LINE IN 3
VIDEO
L - AUDIO - R
S-VIDEO
INPUT SELECT
AM
PM
TINS-3894 ENGLISH.book Page 31 Wednesday, September 6, 2000 11:53 AM
32
If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours)
or www.sharp.co.uk/support
ADVANCED OPERATION
DECODER SWITCHING OPERATION
If you connect a separate decoder to the VCR connected to L2 as previously shown, you will
need to set the decoder function to
need to set the decoder function to
ON
in order to record the descrambled signal and/or
watch it on your TV. Now, when the VCR receives a scrambled signal it is output via LINE 2
terminal to the decoder. The decoder then outputs the descrambled signal back to LINE 2
terminal and the signal can be recorded. The VCR outputs the descrambled signal to your TV
through the LINE1 terminal and you can watch the descrambled picture.
terminal to the decoder. The decoder then outputs the descrambled signal back to LINE 2
terminal and the signal can be recorded. The VCR outputs the descrambled signal to your TV
through the LINE1 terminal and you can watch the descrambled picture.
When making recordings using a separate decoder connected as shown remember to leave
the decoder function ON.
the decoder function ON.
If you connect a decoder unit to the VCR, the decoder unit provides a switching signal which
will automatically allow your TV to display the descrambled signal routed through the VCR. To
use this feature make sure that the VCR is connected to both TV and decoder unit by SCART
leads. Then:
will automatically allow your TV to display the descrambled signal routed through the VCR. To
use this feature make sure that the VCR is connected to both TV and decoder unit by SCART
leads. Then:
•
Press
STANDBY
to place the VCR in Stand-by mode, OR
•
Press
[TV/VCR]
on the remote control to place the VCR in ‘VCR mode’. ‘VCR’ will
appear on the display.
If you switch the decoder function ON when connected to a decoder unit as shown you will
NOT be able to watch the descrambled picture in TV mode or in VCR mode.
NOT be able to watch the descrambled picture in TV mode or in VCR mode.
TINS-3894 ENGLISH.book Page 32 Wednesday, September 6, 2000 11:53 AM
33
If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours)
or www.sharp.co.uk/support
SPECIAL FEATURES ON YOUR VCR
POWERSAVE MODE
ENABLING POWERSAVE MODE
If you wish to use the POWERSAVE feature, it can be switched on within the Mode Menu
Screen, this will automatically disable the STANDBY mode.
Screen, this will automatically disable the STANDBY mode.
1.
Press
MENU
to display the main menu on the
screen.
2.
Press [
/
]to select MODE.
3.
Press
SET
.
4.
Press [
/
]to select POWERSAVE.
5.
Press
[
/
]to select ON.
6.
Press
SET
and then
MENU
to return to the
normal screen.
Press
STANDBY
(
) to place the VCR in POWERSAVE mode. The VCR digital display will
flash save for 5 seconds and will then appear blank.
The VCR power consumption will now be below 1.5 Watt. i.e., The VCR is now in the
POWERSAVE MODE.
POWERSAVE MODE.
AUTO POWERSAVE
If the VCR is not operated for more than 3 hours, the VCR will go into POWERSAVE mode and
the digital display will appear blank.
the digital display will appear blank.
DISENGAGING POWERSAVE MODE
Press
STOP
(
) to use the VCR. (Other keys may also disengage POWERSAVE, such as the
CHANNEL
/
).
STANDBY MODE
The POWERSAVE feature must be OFF for the STANDBY mode to function. This will allow viewing
through the VCR without AUTO POWERSAVE operating. Press
through the VCR without AUTO POWERSAVE operating. Press
STANDBY
(
) to place the
VCR in standby mode.
DISENGAGING STANDBY MODE
Press
STOP
(
) to use the VCR.
NOTES:
•
POWERSAVE mode will not operate when CHILDLOCK is engaged
•
POWERSAVE/STANDBY will operate after auto rewind and cassette will eject.
•
POWERSAVE/STANDBY will operate when TIMER is on.
•
STANDBY will only operate when POWERSAVE is disabled.
•
POWERSAVE will not operate if disabled via the MODE screen.
MODE MENU SCREEN
CO L OUR
AU T O
P A L
B L U E MU T E
AU T O
O F F
R E P E A T
ON
O F F
AUD I O M I X
ON
O F F
1 6 : 9
AU T O
O F F
➝
POWE R S A V E
ON
O F F
TINS-3894 ENGLISH.book Page 33 Wednesday, September 6, 2000 11:53 AM
Click on the first or last page to see other VC-S2000 (serv.man22) service manuals if exist.