Sharp VC-S2000 (serv.man22) User Manual / Operation Manual ▷ View online
14
If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours)
or www.sharp.co.uk/support
BASIC OPERATION
DIRECT TV RECORDING
This feature can only be used with nexTView, Smart Link, Easy Link and
Megalogic compatible tv’s.
Megalogic compatible tv’s.
By pressing the
DIRECT TV REC
button on the remote control, the VCR will record the
signal currently being displayed on the TV regardless of the signal source.
This feature can be started when the VCR is in STANDBY or OPERATE mode.
This feature can be started when the VCR is in STANDBY or OPERATE mode.
•
If
appears on the VCR display, press
TIMER ON/OFF
before starting.
•
Ensure a video tape is inserted into the VCR.
•
Select either S-VHS AUTO or OFF in the Mode Menu for your preferred recording format.
1.
To start the recording, press
DIRECT TV REC
.
2.
To pause during recording, press
PAUSE
(
).
3.
To continue recording, press
REC
(
).
4.
To stop recording, press
STOP
(
).
NOTES:
TIMER RECORDING
It is possible to program the VCR using three different methods:-
1.
NexTView
2.
Videoplus
3.
Manually (DELAYED RECORDING)
HOW TO USE NexTView TO MAKE A RECORDING
•
If
appears on the VCR display, press
TIMER ON/OFF
before starting.
•
Check that the clock is displaying the correct time.
•
Select either S-VHS AUTO or OFF in the Mode Menu for your preferred recording format.
Some broadcasts transmit an Electronic Program Guide (EPG) in which case, using the TV con-
trols, the program you wish to record can be selected and used to program the VCR automat-
ically. This feature is compatible with NexTView TV’s. Refer to your TV operation manual for
further information. After transfer of the timer information to the VCR, the timer menu will be dis-
played for approximately 5 seconds, after which press
trols, the program you wish to record can be selected and used to program the VCR automat-
ically. This feature is compatible with NexTView TV’s. Refer to your TV operation manual for
further information. After transfer of the timer information to the VCR, the timer menu will be dis-
played for approximately 5 seconds, after which press
TIMER ON/OFF
once to place the
VCR in STANDBY mode.
will be shown on the display.
NOTES:
•
Direct TV Recording may not work if the channel download procedure has not been
completed.
completed.
•
A fully wired scart must be used for DIRECT TV RECORD operation.
•
If DIRECT TV RECORD could not start, the TV should indicate the reason why.
(Refer to the TV operation manual).
(Refer to the TV operation manual).
•
The timer menu will not be displayed if this procedure is carried out while the VCR is in
STANDBY mode.
STANDBY mode.
•
VPS/PDC is a signal broadcast by some TV stations which adjusts the start and stop time
of your VCR recording. This ensures that if there is a change in broadcast time for your
programme the VCR will still record the whole programme. It is essential that the start
time as it appears in the TV listing is used to program the VCR, as this information is used
to identify the VPS/PDC signal corresponding to your programme.
of your VCR recording. This ensures that if there is a change in broadcast time for your
programme the VCR will still record the whole programme. It is essential that the start
time as it appears in the TV listing is used to program the VCR, as this information is used
to identify the VPS/PDC signal corresponding to your programme.
•
If
flashes a video tape has not been inserted into the VCR.
•
During recording, press STOP
(
) to cancel the recording. If there are further record-
ings to be made, the VCR will return to TIMER STANDBY.
TINS-3894 ENGLISH.book Page 14 Wednesday, September 6, 2000 11:53 AM
15
If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours)
or www.sharp.co.uk/support
BASIC OPERATION
HOW TO USE TO MAKE A RECORDING
•
If
appears on the VCR display, press
TIMER ON/OFF
before starting.
•
Check that the clock is displaying the correct time.
•
Select either S-VHS AUTO or OFF in the Mode Menu for your preferred recording format.
VIDEOPLUS+ allows you to program the VCR to record up to eight programmes using the
VIDEOPLUS+ numbers published in TV listings...
VIDEOPLUS+ numbers published in TV listings...
1.
Press
PLUSCODE
on the remote control
2.
Enter the VIDEOPLUS+ number from the TV
listing using the
listing using the
NUMBER BUTTONS
.
NOTE:
3.
Press [
/
] to select ONCE, WEEKLY, DAILY
4.
If you want to make additional recordings at the same time each day or week, then use
[
[
/
] to select the WEEKLY, or DAILY option as appropriate.
5.
Press
SET
to confirm..
NOTE:
The first time that you use VIDEOPLUS+ to make a
recording on each channel Preset, (PR) may be
highlighted on the menu.
recording on each channel Preset, (PR) may be
highlighted on the menu.
6.
Enter the channel you wish to record using
the
the
NUMBER BUTTONS
, for example if
you wish to record channel 2 press
0 2
. The
VCR will remember this for the future.
NOTES:
•
An ERROR message will appear if you have entered a number that is not a current
VIDEOPLUS+ number. If this happens press
VIDEOPLUS+ number. If this happens press
CLEAR
to delete the numbers as required
and enter the correct VIDEOPLUS+ number
•
Check that the menu list agrees with the times shown in the TV listing. If it does not press
CLEAR
to return to the VIDEOPLUS+ menu, and re-enter the correct VIDEOPLUS+
number
You may also access the VIDEOPLUS+ menu by the following procedure:
i.
Press
MENU
.
ii.
The VIDEOPLUS+ option will be highlighted. Press
SET
to confirm.
Continue from step 2 above.
1 / 2
DA T E P R
S T AR T
S T OP
2 1 / 0 6
0 2
1 2 : 0 0
1 3 : 0 0
S P *
- - / - -
- -
- : - -
- : - -
- - -
- - / - -
- -
- : - -
- : - -
- - -
- - / - -
- -
- : - -
- : - -
- - -
P R
: BBC 2
: S E L EC T
: CHANGE
S E T
: E N T E R ME NU : E X I T
→
P L U S COD E
-
ONC E
WE E K L Y
DA I L Y
TINS-3894 ENGLISH.book Page 15 Wednesday, September 6, 2000 11:53 AM
16
If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours)
or www.sharp.co.uk/support
BASIC OPERATION
HOW TO USE TO MAKE A RECORDING
7.
If your VCR has long play facility and you wish
to change the
to change the
RECORDING SPEED
, use
the [
/
] to highlight SP. Press [
/
]
to select standard play (SP), long play (LP) or
extended play (EP)as required.
extended play (EP)as required.
8.
[See
NOTE
below]. For VPS/PDC setting use
[
/
] to highlight the final column. Using
the [
/
] will select VPS/PDC ON or OFF
(
✱
= ON
-
= OFF).
9.
Press
SET
to confirm the programme. The
VIDEOPLUS+ menu will reappear. If you wish
to enter further VIDEOPLUS+ recordings
repeat this procedure.
to enter further VIDEOPLUS+ recordings
repeat this procedure.
10.
When you have completed entering timer
settings, press
settings, press
MENU
to remove the menu
from the TV screen.
11.
Ensure that the tape on which you wish to
record is inserted into the VCR, then press
TIMER ON/OFF once to place the VCR in
TIMER STANDBY mode.
record is inserted into the VCR, then press
TIMER ON/OFF once to place the VCR in
TIMER STANDBY mode.
will be shown on
the display.
NOTES:
•
It is essential that the start time as it appears in the TV listing is used to program the VCR,
as this information is used to identify the VPS/PDC signal corresponding to your
programme.
as this information is used to identify the VPS/PDC signal corresponding to your
programme.
•
VPS/PDC is a signal broadcast by some TV stations which adjusts the start and stop time
of your VCR recording. This ensures that if there is a change in broadcast time for your
programme the VCR will still record the whole programme.
of your VCR recording. This ensures that if there is a change in broadcast time for your
programme the VCR will still record the whole programme.
•
If
flashes a video tape has not been inserted into the VCR.
•
If the video tape is ejected when the VCR tries to record the record protection tab has
been removed.
been removed.
•
During recording, press
STOP
(
) to cancel the recording. If there are further
recordings to be made, the VCR will return to TIMER STANDBY.
1 / 2
DA T E P R
S T AR T
S T OP
2 1 / 0 6
0 2
1 2 : 0 0
1 3 : 0 0
S P
*
- - / - -
- -
- : - -
- : - -
- - -
- - / - -
- -
- : - -
- : - -
- - -
- - / - -
- -
- : - -
- : - -
- - -
T A P E
S P E E D :S P / L P
: S E L EC T
: CHANGE
S E T
: E N T E R ME NU : E X I T
1 / 2
DA T E P R
S T AR T
S T OP
2 1 / 0 6
0 2
1 2 : 0 0
1 3 : 0 0
S P
-
- - / - -
- -
- : - -
- : - -
- - -
- - / - -
- -
- : - -
- : - -
- - -
- - / - -
- -
- : - -
- : - -
- - -
V P S / P DC
✱ : ON - : OF F
: S E L EC T
: CHANGE
S E T
: E N T E R ME NU : E X I T
TINS-3894 ENGLISH.book Page 16 Wednesday, September 6, 2000 11:53 AM
17
If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours)
or www.sharp.co.uk/support
BASIC OPERATION
HOW TO SET A DELAYED RECORDING
You can make a maximum of eight delayed recordings up to a year in advance.
The example shown is for 24-hour clock operation. 12-hour clock operation can be selected
from the manual clock setting menu.
from the manual clock setting menu.
12-hour clock am/pm can be selected using the
AM/PM
button on the remote control.
•
If
appears on the VCR display, press
TIMER ON/OFF
before starting.
•
Check that the clock is displaying the correct time.
•
Select either S-VHS AUTO or OFF in the Mode Menu for your preferred recording format.
SETTING A RECORDING
For example: Recording a programme on channel 3 from 21:05 to 22:30 on July 9th.
1.
Press
STOP
(
) to switch on the VCR.
2.
Press
MENU
.
3.
Press [
/
] to select TIMER. Press
SET
to
confirm.
4.
The position which is initially highlighted is the
next available timer record entry. Press
next available timer record entry. Press
SET
to
confirm this.
•
The display will automatically show today's
date.
Either: If this is the date you wish to make the
recording on, press
date.
Either: If this is the date you wish to make the
recording on, press
SET
to confirm this.
Or: enter the recording date using the
[
[
/
] or the
NUMBER BUTTONS
.
Enter two digits for the day, then two for the
month. For example for July 9th, press
month. For example for July 9th, press
0 9
(9th),
then
0 7
(July).
5.
Then press
SET
to confirm.
6.
If you want to make additional recordings at
the same time each day or week, use
[
the same time each day or week, use
[
/
] or select D (daily) or W (weekly).
Then press
SET
to confirm.
7.
Enter the channel using the [
/
] or the
NUMBER BUTTONS
. For example to
record a programme on channel 3, press 0 3.
Then press
Then press
SET
to confirm.
MENU SCREEN
T I ME R
MOD E
S E T U P
: S E L EC T
S E T
: E N T E R ME NU : E X I T
1 / 2
DA T E P R
S T AR T
S T OP
2 1 / 0 6
0 2
1 2 : 0 0
1 3 : 0 0
S P *
9 / 0 7
- -
- : - -
- : - -
- - -
- - / - -
- -
- : - -
- : - -
- - -
- - / - -
- -
- : - -
- : - -
- - -
1 / 2
DA T E P R
S T AR T
S T OP
2 1 / 0 6
0 2
1 2 : 0 0
1 3 : 0 0
S P *
9 / 0 7
D
- -
- : - -
- : - -
- - -
- - / - -
- -
- : - -
- : - -
- - -
- - / - -
- -
- : - -
- : - -
- - -
TINS-3894 ENGLISH.book Page 17 Wednesday, September 6, 2000 11:53 AM
Click on the first or last page to see other VC-S2000 (serv.man22) service manuals if exist.