Sharp VC-S2000 (serv.man22) User Manual / Operation Manual ▷ View online
22
If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours)
or www.sharp.co.uk/support
ADVANCED OPERATION
AUDIO DUBBING
RECORDING SOUND ON TO A VIDEO TAPE (AUDIO DUBBING)
This feature enables you to add narration or background music to a pre-recorded tape.
•
The audio signal will be recorded on the mono track. The Hi-Fi track will remain
unchanged..
unchanged..
1.
Connect the audio source to the AUDIO
IN L-R terminals on the front of the VCR as
shown above.
IN L-R terminals on the front of the VCR as
shown above.
2.
Insert the pre-recorded tape into the
VCR.
VCR.
3.
Press
PLAY/X2
(
) to view the
recording.
4.
If you wish to listen to the original Hi-Fi
track while you are recording the new
dubbed audio track you will need to set
AUDIO MIX to ON in the mode menu.
track while you are recording the new
dubbed audio track you will need to set
AUDIO MIX to ON in the mode menu.
5.
Press
PAUSE/STILL
(
) when you
reach the point on the tape where you
want audio dubbing to start.
want audio dubbing to start.
6.
Press
A.DUB
(
A.DUB
will be shown on
your TV)
NOTE:
The input source will be
automatically changed to L3 (Front
phono jacks)
phono jacks)
7.
Press
PAUSE/STILL
(
) , to start audio
dubbing.
8.
Press
STOP
(
) , to finish audio dubbing
(
A.DUB
will disappear from your TV)
+
Connect your
audio equipment
to AUDIO IN L-R
terminals on the
front of your VCR.
audio equipment
to AUDIO IN L-R
terminals on the
front of your VCR.
If a microphone is to be used,
connect it to your audio
equipment
connect it to your audio
equipment
AUDIO SOURCE
II A. DUB
L3
SP
TINS-3894 ENGLISH.book Page 22 Wednesday, September 6, 2000 11:53 AM
23
If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours)
or www.sharp.co.uk/support
ADVANCED OPERATION
AUDIO DUBBING
PLAYING BACK AN AUDIO DUBBED TAPE
•
If you want to listen to the original and the new dubbed audio signal simultaneously, you will
need to set AUDIO MIX to ON.
need to set AUDIO MIX to ON.
•
You can change the audio output by pressing the AUDIO OUT button on the remote
control. Refer to the table below.
control. Refer to the table below.
1.
Press
MENU
, to display the main menu
on the screen.
2.
Press [
/
to select MODE.
3.
Press
SET
.
4.
Press [
/
] to select AUDIO MIX.
5.
Press [
/
] to select ON.
6.
Press
SET
, to return to the menu screen.
7.
Press
MENU
, to exit to the normal screen.
NOTES: .
AUDIO MIX
AUDIO OUT MODE
VCR DISPLAY
RESULT
ON
Hi-Fi and Mono audio
Original Hi-Fi audio (L&R
channels) and dubbed audio
Original Hi-Fi audio (L channel)
plus dubbed audio
Original Hi-Fi audio (R channel)
plus dubbed audio
•
Do not start audio dubbing until AUTO or MANUAL tracking has been completed as the
audio signal will not be recorded correctly.
audio signal will not be recorded correctly.
•
Because the audio signal is recorded onto the mono track any previous recording on
this track will be erased.
this track will be erased.
•
If AUDIO MIX in the mode menu is set to OFF, no sound will be heard during audio
dubbing.
dubbing.
AUDIO MIX
ON
OF F
16: 9
AUTO
OF F
POWERS AVE
ON
OF F
▲
▲
2/ 2
▲
▲
▲▼ :SELECT
:CHANGE
SET
:ENTER
MENU
:EXIT
MODE MENU SCREEN
▲
▲
➞
TINS-3894 ENGLISH.book Page 23 Wednesday, September 6, 2000 11:53 AM
24
If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours)
or www.sharp.co.uk/support
ADVANCED OPERATION
DIGITAL DISPLAY
TIME OF DAY
Shows current time of day, if the clock is set. Press
DISPLAY
until the time of day appears. For example,
21:20 appears:
Operation Mode
Shows status of tape. Press DISPLAY until the display
appears, for example:
TAPE COUNTER AND ZERO BACK
Tape counter measures the current position of the video tape in real time. ZERO BACK uses the
tape counter to determine a specific point on a tape you may wish to return to.
tape counter to determine a specific point on a tape you may wish to return to.
1.
Press
DISPLAY
until tape counter appears, for
example:
2.
To identify the current position on a video tape
press
press
CLEAR
on the remote control or
COUNTER
RESET
on the VCR’s control
panel and the tape counter will appear:
When you wish to return to this position on the video tape, press
ZERO BACK
The tape will
rewind/advance to this point.
NOTE:
•
The tape counter will only operate on recorded sections of tape.
PR
PR
PR
PR
PR
TINS-3894 ENGLISH.book Page 24 Wednesday, September 6, 2000 11:53 AM
25
If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours)
or www.sharp.co.uk/support
ADVANCED OPERATION
PLAYBACK OF A VIDEO TAPE
CHECKING THE AMOUNT OF TAPE REMAINING
When you load a video tape into the VCR it can calculate approximately the amount of
video tape remaining in hours and minutes. This is useful in determining whether or not there is
sufficient tape left to make a recording.
video tape remaining in hours and minutes. This is useful in determining whether or not there is
sufficient tape left to make a recording.
When a video tape is playing, the amount of tape remaining is calculated for you
automatically.
automatically.
To display the amount of video tape remaining:
1.
Load the video tape into the VCR
2.
Press
DISPLAY
on the remote control as many times as necessary until “R” appears on
the VCR display. The tape will wind forward and then return to its original position. The
tape remaining will be shown on the VCR display in hours and minutes.
By pressing the
tape remaining will be shown on the VCR display in hours and minutes.
By pressing the
TAPE SPEED
button on the remote control the remaining time will
change between long play and standard play
For example, if 1 hour 23 minutes is left on the tape
In long play 2 hour 46 minutes is left on the tape:
NOTES:
PLAYING BACK A VIDEO TAPE REPEATEDLY
You can set your VCR to automatically rewind at the end of playing a video tape and replay
the entire tape again. REPEAT will appear on the on-screen display when selected.
the entire tape again. REPEAT will appear on the on-screen display when selected.
To use this feature:
1.
Press
MENU
to display the main menu on the
screen.
2.
Press [
/
] to select MODE.
3.
Press
SET
.
4.
Press [
/
] to select REPEAT.
5.
Press [
/
] to select ON.
6.
Press
SET
.
7.
Press
MENU
to return to normal screen.
•
Do not interrupt the tape remaining calculation.
•
If less than 5 minutes of tape remains the display will flash.
SP
SP
AM PM
TIMER
REC
LP
L
ET
R
V PS P D
S-VHS
VCR
DEC
AV
PR
STOP
MODE MENU SCREEN
B L U E MU T E
AU T O
O F F
➝
R E P E A T
ON
O F F
AUD I O M I X
ON
O F F
1 6 . 9
AU T O
O F F
POWE R S A V E
ON
O F F
2 / 2
: S E L EC T
: CHANGE
S E T
: E N T E R ME NU : E X I T
PR
TINS-3894 ENGLISH.book Page 25 Wednesday, September 6, 2000 11:53 AM
Click on the first or last page to see other VC-S2000 (serv.man22) service manuals if exist.