Sharp VC-MH835 (serv.man24) User Manual / Operation Manual ▷ View online
23
www.sharp.co.uk/support
ADVANCED OPERATION
AUDIO AND YOUR VCR
CONNECTING TO AUDIO EQUIPMENT
The diagram below shows how to connect your VCR to audio equipment. When connected
in this way stereo sound is possible from the speakers.
in this way stereo sound is possible from the speakers.
LINE1(I)IN
/OUT
SON/VIDEO
(L1/I)
A2230
LINE2(II)IN/DECODER CANAL PLUS/L2(II)
AUDIO OUT
SORTIE SON
L G
R D
AERIAL IN
ENTREE ANTENNE
AERIAL OUT
SORTIE ANTENNE
+
BACK OF
EXISTING AERIAL
CABLE
RF CONNECTION CABLE
AERIAL OUT
AUDIO OUT
AMPLIFIER
L and R
TELEVISION
AERIAL IN
AUDIO PHONO LEADS
(NOT SUPPLIED)
TINS-A082UMN1.book Page 23 Monday, November 4, 2002 2:33 PM
24
www.sharp.co.uk/support
ADVANCED OPERATION
PLAYBACK OF A VIDEO TAPE
PLAYING BACK AN S-VHS TAPE
S-VHS (super -VHS) pre-recorded tapes give you a better quality playback picture with
increased detail and depth.
Your VCR will automatically recognise which type of tape is being used, VHS or S-VHS and
playback the appropriate standard accordingly.
NOTES:
PLAYING BACK AN NTSC TAPE
NTSC (National Television Standards Committee) is a different TV standard to PAL and is used
in some Non-European Countries. Your VCR can playback pre-recorded NTSC tapes onto a
PAL system TV, but cannot record an NTSC signal onto a video tape.
Note that..
•
You cannot record NTSC signals or dub NTSC tapes onto other VCR’s from this VCR.
•
You cannot use Slow speed, Still frame, Double Speed, Frame Advance or Tape
Remaining with a pre-recorded NTSC tape.
•
On some televisions, the picture may appear in black and white or there may be no
picture. This does not indicate a fault with your VCR.
•
On some televisions, the picture may shrink vertically causing black bands to appear at
the top and bottom of your screen.
•
On some televisions, the played-back picture may roll vertically, this does not indicate a
fault with your VCR.
•
All of the VCR’s playback functions can be used during S-VHS playback, SLOW,
PLAY/X2 VISUAL SEARCH, etc.
•
Your VCR is S-VHS playback only, it will not record S-VHS.
•
Some picture noise may be observed on the screen in Long Play (LP) mode.
TINS-A082UMN1.book Page 24 Monday, November 4, 2002 2:33 PM
25
www.sharp.co.uk/support
ADVANCED OPERATION
PLAYBACK OF A VIDEO TAPE
CHECKING THE AMOUNT OF TAPE REMAINING
When you load a video tape into the VCR it can calculate approximately the amount of
video tape remaining in hours and minutes. This is useful in determining whether or not there is
sufficient tape left to make a recording.
When a video tape is playing, the amount of tape remaining is calculated for you
automatically.
To display the amount of video tape remaining:
video tape remaining in hours and minutes. This is useful in determining whether or not there is
sufficient tape left to make a recording.
When a video tape is playing, the amount of tape remaining is calculated for you
automatically.
To display the amount of video tape remaining:
1.
Load the video tape into the VCR
2.
Press
DISPLAY
on the remote control as many times as necessary until “R” appears on
the VCR display. The tape will wind forward for a few seconds and then return to its
original position. The tape remaining will be shown on the VCR display in hours and
minutes.
By pressing the
original position. The tape remaining will be shown on the VCR display in hours and
minutes.
By pressing the
TAPE SPEED
button on the remote control the remaining time will
change between standard play, long play and extended play.
For example,
in standard play 1 hour 23 minutes is left on the tape:
in standard play 1 hour 23 minutes is left on the tape:
in long play 2 hours 46 minutes is left on the tape:
in extended play 4 hours 9 minutes is left on the tape:
NOTES:
PLAYING BACK A VIDEO TAPE REPEATEDLY
You can set your VCR to automatically rewind at the end of playing a video tape and replay
the entire tape again. REPEAT will appear on the on-screen display when selected.
To use this feature:
the entire tape again. REPEAT will appear on the on-screen display when selected.
To use this feature:
1.
Press the
MENU
button to display the
main menu on the screen.
2.
Press the[
/
]menu select buttons to
select MODE.
3.
Press the
SET
button.
4.
Press [
/
]to select REPEAT.
5.
Press
[
/
]
to select ON or OFF.
6.
Press the
SET
button to confirm and return
to the main menu screen.
7.
Press the
MENU
button to exit to normal
screen.
•
If tape remaining function is interrupted, the remaining time will not be displayed.
•
If less than 5 minutes of tape remains the display will flash.
MODE MENU SCREEN
B L U E MU T E
AU T O
O F F
➝
R E P E A T
ON
O F F
1 6 : 9
ON
O F F
: S E L EC T
: CHANGE
S E T
: E N T E R ME NU : E X I T
SET
SET
TINS-A082UMN1.book Page 25 Monday, November 4, 2002 2:33 PM
26
www.sharp.co.uk/support
ADVANCED OPERATION
LCD DISPLAY
TIME OF DAY
Shows current time of day, if the clock is set.
Press the
DISPLAY
button until the time of day
appears. For example, 21:20 appears:
CHANNEL STATUS
Shows the current VCR channel preset. Press the
DISPLAY
button until the channel number
appears, for example:
TAPE COUNTER AND ZERO BACK
Tape counter measures the current position of the video tape in real time. ZERO BACK uses the
tape counter to determine a specific point on a tape you may wish to return to.
tape counter to determine a specific point on a tape you may wish to return to.
1.
Press the
DISPLAY
button until tape
counter appears, for example:
2.
To identify the current position on a video tape
press the
CLEAR
button and the tape
counter will appear:
When you wish to return to this position on the video tape, press
ZERO BACK
button.
The tape will rewind/advance to this point.
NOTE:
DISPLAY BRIGHTNESS
The LCD display brightness can be changed to suit the ambient lighting in the room. Switch
on the VCR (ensure the menu screen is not on) then press and hold the
on the VCR (ensure the menu screen is not on) then press and hold the
DISPLAY
button for
approximately 2 seconds. This will reduce the brightness of the VCR display. Repeat the
process to change the display back to the previous setting.
process to change the display back to the previous setting.
•
The tape counter will only operate on recorded sections of tape.
TINS-A082UMN1.book Page 26 Monday, November 4, 2002 2:33 PM
Click on the first or last page to see other VC-MH835 (serv.man24) service manuals if exist.