Sharp VC-MH732HM (serv.man29) User Manual / Operation Manual ▷ View online
GB-13
BASIC OPERATION
HOW TO PLAYBACK A VIDEO TAPE
FAST FORWARDING/REWINDING A VIDEO TAPE
1.
Press
STOP
(
) to stop the video tape.
2.
Press
FAST FORWARD
(
)/
REWIND
(
) on the remote control or turn the
shuttle ring on the VCR fully to the Right for Fast Forward and fully to the Left for Rewind
and Release.
and Release.
3.
To stop fast forward/rewind, press
STOP
(
).
FORWARD/REVERSE VISUAL SEARCH
1.
During playback for continuous search mode, press
FAST FORWARD
(
)/
REWIND
(
) on the remote control, or turn the shuttle ring fully to the Right for
Forward Visual Search or fully to the Left for Reverse Visual Search then Release. (On
release the shuttle returns back to starting position). Press
release the shuttle returns back to starting position). Press
PLAY/X2
(
) to resume
playback.
OR
2.
To decrease the speed, during visual search mode press
FAST FORWARD
(
)/
REWIND
(
) again, or turn and hold the shuttle ring halfway to the Right for Forward
Visual Search or Left for Reverse Visual Search. Release the shuttle to resume playback or
If the remote control was used press
If the remote control was used press
PLAY/X2
(
).
NOTE:
•
There will be picture interference and possibly a change to black and white picture
using Visual Fast Forward/Rewind functions.
using Visual Fast Forward/Rewind functions.
If problems persist contact the SHARP Customer Helpline on tel: 0990-274277
GB-14
BASIC OPERATION
IMMEDIATE RECORDING
SELECTION OF A CHANNEL
Select the channel by using the number buttons on the remote control, or select the
next/previous channel by pressing
next/previous channel by pressing
CHANNEL
[
or
].
To change between single digit and 2-digit channel numbers, press
AM/PM
.
For example, for channel 24, press
AM/PM
then press
2
4
.
You can record the channel you are watching or any other preset channel.
1.
Insert a video tape into your VCR.
2.
Select the channel you wish to record on the VCR.
3.
To start recording, press
REC
(
).
4.
To pause during recording, press
PAUSE/STILL
(
).
5.
To continue recording, press
REC
(
).
6.
To stop recording, press
STOP
(
) once.
SIMPLE TIMED RECORDING:
1.
To specify a stop time, press
REC
(
).
2.
Each additional press of
REC
(
) will delay
the stop time by 10 minutes.
3.
To stop recording at any time, press
STOP
(
) once.
NOTES:
•
If the tape ends before the recording is complete the VCR will stop recording, rewind,
eject the tape, and place the VCR into Stanby mode.
eject the tape, and place the VCR into Stanby mode.
•
If the VCR ejects the video tape when you press
REC
(
) the tape is record
protected. i.e. record protection tab has been removed.
STOP 15:30
If problems persist contact the SHARP Customer Helpline on tel: 0990-274277
GB-15
BASIC OPERATION
HOW TO USE TO MAKE A RECORDING
•
If
appears on the VCR display, press
TIMER ON/OFF
before starting.
•
Check that the clock is displaying the correct time.
VIDEOPLUS+ allows you to program the VCR to record up to eight programmes using the
VIDEOPLUS+ numbers published in TV listings...
VIDEOPLUS+ numbers published in TV listings...
1.
Press [
SV/V+
] on the remote control
2.
Enter the VIDEOPLUS+ number from the TV
listing using the
listing using the
NUMBER BUTTONS
.
NOTE:
3.
Press [
/
] to select ONCE, WEEKLY, DAILY
4.
If you want to make additional recordings at the same time each day or week, then use
[
[
/
] to select the WEEKLY, or DAILY option as appropriate.
5.
Press
SET
to confirm..
NOTE:
The first time that you use VIDEOPLUS+ to make a
recording on each channel Preset, (PR) may be
highlighted on the menu.
recording on each channel Preset, (PR) may be
highlighted on the menu.
6.
Enter the channel you wish to record using
the
the
NUMBER BUTTONS
, for example if
you wish to record channel 2 press
0 2
. The
VCR will remember this for the future.
NOTES:
•
An ERROR message will appear if you have entered a number that is not a current
VIDEOPLUS+ number. If this happens press
VIDEOPLUS+ number. If this happens press
CLEAR
to delete the numbers as required
and enter the correct VIDEOPLUS+ number
•
Check that the menu list agrees with the times shown in the TV listing. If it does not press
CLEAR
to return to the VIDEOPLUS+ menu, and re-enter the correct VIDEOPLUS+
number
You may also access the VIDEOPLUS+ menu by the following procedure:
i.
Press
MENU
.
ii.
The VIDEOPLUS+ option will be highlighted. Press
SET
to confirm.
Continue from step 2 above.
1 / 2
DA T E P R
S T AR T
S T OP
2 1 / 0 6
0 2
1 2 : 0 0
1 3 : 0 0
S P *
- - / - -
- -
- : - -
- : - -
- - -
- - / - -
- -
- : - -
- : - -
- - -
- - / - -
- -
- : - -
- : - -
- - -
P R
: BBC 2
O P
: S E L E C T
M N
: CHANGE
S E T
: E N T E R ME NU : E X I T
→
P L U S COD E .
-
ONC E
WE E K L Y
DA I L Y
If problems persist contact the SHARP Customer Helpline on tel: 0990-274277
GB-16
BASIC OPERATION
HOW TO USE TO MAKE A RECORDING
7.
If your VCR has long play facility and you wish
to change the
to change the
RECORDING SPEED
, use
the [
/
] to highlight SP. Press [
/
]
to select standard play (SP) or long play (LP)
as required.
as required.
8.
[See
NOTE
below]. For VPS/PDC setting use
[
/
] to highlight the final column. Using
the [
/
] will select VPS/PDC ON or OFF
(
✱
= ON
-
= OFF).
9.
Press
SET
to confirm the programme. The
VIDEOPLUS+ menu will reappear. If you wish
to enter further VIDEOPLUS+ recordings
repeat this procedure.
to enter further VIDEOPLUS+ recordings
repeat this procedure.
10.
When you have completed entering timer
settings, press
settings, press
MENU
to remove the menu
from the TV screen.
11.
Press TIMER ON/OFF once to place the VCR
in TIMER STANDBY mode.
in TIMER STANDBY mode.
will be shown on
the display.
NOTES:
•
VPS/PDC is a signal broadcast by some TV stations which adjusts the start and stop time
of your VCR recording. This ensures that if there is a change in broadcast time for your
programme the VCR will still record the whole programme. It is essential that the start
time as it appears in the TV listing is used to program the VCR, as this information is used
to identify the VPS/PDC signal corresponding to your programme.
of your VCR recording. This ensures that if there is a change in broadcast time for your
programme the VCR will still record the whole programme. It is essential that the start
time as it appears in the TV listing is used to program the VCR, as this information is used
to identify the VPS/PDC signal corresponding to your programme.
•
If
flashes a video tape has not been inserted into the VCR.
•
If the video tape is ejected when the VCR tries to record the record protection tab has
been removed.
been removed.
•
During recording, press
STOP
(
) to cancel the recording. If there are further
recordings to be made, the VCR will return to TIMER STANDBY.
1 / 2
DA T E P R
S T AR T
S T OP
2 1 / 0 6
0 2
1 2 : 0 0
1 3 : 0 0
S P
*
- - / - -
- -
- : - -
- : - -
- - -
- - / - -
- -
- : - -
- : - -
- - -
- - / - -
- -
- : - -
- : - -
- - -
T A P E
S P E E D :S P / L P
O P
: S E L E C T
M N
: CHANGE
S E T
: E N T E R ME NU : E X I T
1 / 2
DA T E P R
S T AR T
S T OP
2 1 / 0 6
0 2
1 2 : 0 0
1 3 : 0 0
S P
-
- - / - -
- -
- : - -
- : - -
- - -
- - / - -
- -
- : - -
- : - -
- - -
- - / - -
- -
- : - -
- : - -
- - -
V P S / P DC
✱
: ON - : O F F
O P
: S E L E C T
M N
: CHANGE
S E T
: E N T E R ME NU : E X I T
If problems persist contact the SHARP Customer Helpline on tel: 0990-274277
Click on the first or last page to see other VC-MH732HM (serv.man29) service manuals if exist.