Sharp VC-M333 (serv.man5) User Manual / Operation Manual ▷ View online
16
If problems persist contact the SHARP Helpline on tel: 0990-274277
BASIC OPERATION
HOW TO CHECK, CHANGE AND CANCEL A DELAYED
RECORDING
RECORDING
Before you start!
•
If
appears on the VCR display, press
TIMER ON/OFF
to remove the
symbol.
CHECKING A RECORDING
1.
Press
STOP
to switch on the VCR.
2.
Press
MENU
.
3.
Press [
/
]to select
TIMER
. Press
SET
to
confirm.
•
All the delayed recordings in the VCR’s memory
will be shown.
will be shown.
4.
If the settings are correct press
MENU
to exit.
•
If you wish to change or cancel any settings,
follow the procedures below.
follow the procedures below.
CHANGING A RECORDING
1.
Follow steps 1 to 3 of
CHECKING A
RECORDING
.
2.
To change a delayed recording, press
[
[
/
] to highlight the recording, then press
SET
to select.
3.
Press
[
/
]
to highlight the setting to be
changed and correct it by using the [
/
]
or the
NUMBER BUTTONS
.
4.
When all corrections are complete press
SET
to
confirm, then press
MENU
to exit.
CANCELLING A RECORDING
1.
Follow steps 1 to 3 of
CHECKING A
RECORDING
.
2.
To cancel a delayed recording, press
[
[
/
] to highlight the recording to be
cancelled, then press
CLEAR
.
3.
Press
MENU
to exit.
NOTE:
•
If there are some programmes to be recorded, do not forget to press
TIMER ON/OFF
button to return the VCR to TIMER POWERSAVE/TIMER STANDBY mode.
MENU SCREEN
T I ME R
MOD E
S E T U P
: S E L EC T
S E T
: E N T E R ME NU : E X I T
1 / 2
DA T E P R
S T AR T
S T OP
2 1 / 0 6
0 2
1 2 : 0 0
1 3 : 0 0
S P *
- - / - -
- -
- : - -
- : - -
- - -
- - / - -
- -
- : - -
- : - -
- - -
- - / - -
- -
- : - -
- : - -
- - -
1 / 2
DA T E P R
S T AR T
S T OP
2 1 / 0 6
0 2
1 2 : 0 0
1 3 : 0 0
S P *
- - / - -
- -
- : - -
- : - -
- - -
- - / - -
- -
- : - -
- : - -
- - -
- - / - -
- -
- : - -
- : - -
- - -
TINS-3809UMZZ ENGLISH.book Page 16 Monday, April 3, 2000 2:03 PM
17
If problems persist contact the SHARP Helpline on tel: 0990-274277
ADVANCED OPERATION
PLAYBACK OF A VIDEO TAPE
CHECKING THE AMOUNT OF TAPE REMAINING
When you load a video tape into the VCR it can calculate approximately the amount of
video tape remaining in hours and minutes. This is useful in determining whether or not there is
sufficient tape left to make a recording.
When a video tape is playing, the amount of tape remaining is calculated for you
automatically.
To display the amount of video tape remaining:
1.
Load the video tape into the VCR
2.
Press
DISPLAY
on the remote control as many times as necessary until “R” appears on
the VCR display. The tape will wind forward and then return to its original position. The
tape remaining will be shown on the VCR display in hours and minutes.
By pressing the
TAPE SPEED
button on the remote control the remaining time will
change between long play and standard play.
For example,
in standard play 1 hour 23 minutes is left on the tape:
in standard play 1 hour 23 minutes is left on the tape:
in long play 2 hour 46 minutes is left on the tape:
NOTES:
PLAYING BACK A VIDEO TAPE REPEATEDLY
You can set your VCR to automatically rewind at the end of playing a video tape and replay
the entire tape again. REPEAT will appear on the on-screen display when selected.
the entire tape again. REPEAT will appear on the on-screen display when selected.
To use this feature:
1.
Press
MENU
to display the main menu on the
screen.
2.
Press the[
/
]menu select buttons to
select MODE.
3.
Press
SET
.
4.
Press [
/
]to select REPEAT.
5.
Press
[
/
]
to select ON.
6.
Press
SET
.
7.
Press
MENU
to return to normal screen.
•
If tape remaining function is interrupted, the remaining time will not be displayed.
•
If less than 5 minutes of tape remains the display will flash.
PR
PR
PR
PR
MODE MENU SCREEN
B L U E MU T E
AU T O
O F F
➝
R E P E A T
ON
O F F
POWE R S A V E
ON
O F F
: S E L EC T
: CHANGE
S E T
: E N T E R ME NU : E X I T
TINS-3809UMZZ ENGLISH.book Page 17 Monday, April 3, 2000 2:03 PM
18
If problems persist contact the SHARP Helpline on tel: 0990-274277
ADVANCED OPERATION
PLAYBACK OF A VIDEO TAPE
PLAYING BACK AN NTSC TAPE
NTSC (National Television Standards Committee) is a different TV standard to PAL and is used
in some Non-European Countries. Your VCR can playback pre-recorded NTSC tapes onto a
PAL system TV, but cannot record an NTSC signal onto a video tape.
Note that..
•
You cannot record NTSC signals or dub NTSC tapes onto other VCR’s from this VCR.
•
You cannot use Slow speed, Still frame, Double Speed, Frame Advance or Tape
Remaining with a pre-recorded NTSC tape.
•
On some televisions, the picture may appear in black and white or there may be no
picture. This does not indicate a fault with your VCR.
•
On some televisions, the picture may shrink vertically causing black bands to appear at
the top and bottom of your screen.
•
On some televisions, the played-back picture may roll vertically, this does not indicate a
fault with your VCR.
TINS-3809UMZZ ENGLISH.book Page 18 Monday, April 3, 2000 2:03 PM
19
If problems persist contact the SHARP Helpline on tel: 0990-274277
ADVANCED OPERATION
DIGITAL DISPLAY
TIME OF DAY
Shows current time of day, if the clock is set.
Press
Press
DISPLAY
until the time of day appears. For
example, 21:20 appears:
OPERATION MODE
Shows status of tape. Press
DISPLAY
until the display
appears, for example:
TAPE COUNTER AND ZERO BACK
Tape counter measures the current position of the video tape in real time. ZERO BACK uses the
tape counter to determine a specific point on a tape you may wish to return to.
tape counter to determine a specific point on a tape you may wish to return to.
1.
Press
DISPLAY
until tape counter appears, for
example:
2.
To identify the current position on a video tape
press
press
CLEAR
and the tape counter will appear:
When you wish to return to this position on the video tape, press
ZERO BACK
. The tape will
rewind/advance to this point.
NOTE:
•
The tape counter will only operate on recorded sections of tape.
PR
PR
PR
PR
PR
PR
PR
TINS-3809UMZZ ENGLISH.book Page 19 Monday, April 3, 2000 2:03 PM
Click on the first or last page to see other VC-M333 (serv.man5) service manuals if exist.