DOWNLOAD Sharp LC-70UQ10KN (serv.man3) Service Manual ↓ Size: 12.93 MB | Pages: 88 in PDF or view online for FREE

(DYNAMIC MODE)

Level

Referenc Adjustme Inspectio

 x=0.2720
y=0.2770

x=0.2755
y=0.2720
x=0.2755
y=0.2720
x=0.2755
y=0.2720
x=0.2755
y=0.2720
x=0.2755
y=0.2720
x=0.2755
y=0.2720

(MOVIE THX MODE)

Level

Referenc Adjustme Inspectio

x=0.3127
y=0.3290
x=0.3127
y=0.3290
x=0.3127
y=0.3290
x=0.3127
y=0.3290
x=0.3127
y=0.3290
x=0.3127
y=0.3290
x=0.3127
y=0.3290

928

±0.0010 ±0.0020

Remarks

For inspection, set the LCD TV 

Point 7

AV MODE : [DYNAMIC]
Monochrome : ON
Active Backlight : OFF
Aging time : Minimum 60 min.

AV MODE : [MOVIE THX]
Monochrome : ON
Active Backlight : OFF
Aging time : Minimum 60 min.

Point 1

80

---------

--

---------

-

Remarks

Point 7

Point 6

784

±0.0010 ±0.0020

Point 5

624

±0.0015

±0.0030

±0.0020 ±0.0040

Point 3

304

±0.0030 ±0.0060

Point 4

432

±0.0040 ±0.0080

Point 1

80

------------------

Point 2

192

928

±0.0010 ±0.0020

Point 6

784

±0.0010 ±0.0020

±0.0015 ±0.0030

Point 4

432

±0.0020 ±0.0040

Point 5

624

For inspection, set the LCD TV 

±0.0030 ±0.0060

Point 2

192

±0.0040 ±0.0080

Point 3

304

12. Confirmation item

1. HDMI-CEC Inspection

After repairing the CEC function, check the operation about HDMI-CEC circuit

2. CI card Inspection

After repairing the CI function, check that the DTV signal is received by inserting CAM
And check the KEY certification by inserting CAM which is prepare for CI+

3. LAN/NET/SD CARD Connection Check

After repairing the LAN/NET/SD CARD  function, check the communication by connecting PC and LAN terminal.
And  test connectivity of SD card.

4. 3D picture Check

With the signal for 3D check, it checks being displayed normally.

5. Bluetooth and WiFi communication Check

Bluetooth：Please check that it is connectable using a general-purpose Bluetooth devices.
WiFi：Please check that it is connectable using a general-purpose WiFi router.

6. Operation manual Check

13. Initialization to factory settings

CAUTION: When the factory settings have been made, all user setting data, including the channel settings, are initialized.
 (The adjustments done in the adjustment process mode are not initialized.) Keep this in mind when initializing these settings.

 Adjustment item 

 Adjustment conditions

 Adjustment procedure

1  Factory settings 

Ends by turning off the

[Factory setting with adjustment process mode]

 MAIN POWER key.

・Enter the adjustment process mode.

 (See to below caution)

・Move the cursor to [INDUSTRY INIT] on page 2/30.
・Use the R/C key to select a region from [EUROPE/RUSSIA/ SWEDEN] and
  press the [OK] key .
・ “EXECUTING” display appears.
・After a while, “SUCCESS” display appears, the setting is completed.

When succeeding: Background color (green)
When failing: Background color (red)
The following items are initialized in the factory setting.
1) User settings
2) Channel data (e.g. broadcast frequencies)
3) Maker option setting
4) Password data

After adjustments, exit the adjustment process mode.
To exit the adjustment process mode, unplug the AC power cord from the outlet to forcibly turn off the power.
When the power is turned off with the remote control, unplug the AC power cord and plug it back in (wait approximately 20 seconds 
 before plugging in the AC power cord)
After completing the NET connection., execute the NET initialization (Record of the server access)

Please execute the initialized in the factory setting again when you turn on the power supply 
after the initialized in the factory setting is set.

1. HDMI-CEC Inspection

After repairing the CEC function, check the operation about HDMI-CEC circuit

2. CI card Inspection

After repairing the CI function, check that the DTV signal is received by inserting CAM.
And check the KEY certification by inserting CAM which is prepare for CI+.

3. LAN/NET/SD CARD Connection Check

After repairing the LAN/NET/SD CARD function, check the c ommunication by connecting PC and LAN 
terminal.
And test connectivity of SD card.

4. 3D picture Check

With the signal for 3D check, it checks being displayed normally.

5. Bluetooth and Wi-Fi communication Check

Bluetooth: Please check that it is connectable using a general-purpose Bluetooth devices.
WiFi: Please check that it is connectable using a general-purpose WiFi router.

6. Operation manual Check.

1 Turn on the AC power.

 Insert the upgrading USB flash memory for upgrade into the service slot.

 Use the Menu button and cursor keys (◄/► / ▲/▼) , P keys (r/s) of R/C or on the set to select

“HOME” > “TV Menu” > “Setup” > “Information” > “Software update” > “USB update”.on OSD menu.

 If software update file is detected on a network server, the following screen shows up.

For a while, change to the next screen automatically if there is no problem.

Note
•  If not connectable with a network, caution shows up.

Cannot reach the server. Check the network settings and try again.

•  If there is no software update file on a network server or software update file there is already installed, caution 

shows up.

 The caution for update shows up. Select “Yes” if there is no problem.

6 Software update starts.
Please wait for a while until the bar shows 100%

•  Do not disconnect the network server during updating.

HOW TO UPDATE THE SOFTWARE -NETWORK UPDATE-]

1 Turn on the AC power.

2 Insert the upgrading USB flash memory for upgrade into the service slot.

3 Use the Menu button and cursor keys (　　　　 / ▲/▼) ,　Ｃｈ keys (∧/∨) 

of R/C or on the set to select 
 “HOME” > “TV Menu” > “Setup” > “Information” > “Software update” > “USB update”.on OSD menu.

4 If software update file is detected on a network server, the following screen shows up.

For a while, change to the next screen automatically if there is no problem.

Note

・ If not connectable with a network, caution shows up.

Cannot reach the server. Check the network settings and try again.

・ If there is no software update file on a network server or

software update file there is already installed, caution shows up.

Abort

 

ENTER:Enter

5 The caution for update shows up.

Select "Yes" if there is no problem.

Current version

xxxxxxxxxxxx

Latest version

xxxxxxxxxxxx

Estimated update time

xxxxxxxxxxxx

According to the change of the network environment,

 the time actually will change from above one.

Yes

No

6 Software update starts.

Please wait for a while until the bar shows 100%

Note

・ Do not disconnect the network server during updating

Update version

xxxxxxxxxxxx

75%

Abort

7 When all the procedures are completed, the following upgrade success screen shows up.

Select "OK" if there is no problem.

ＴＶ

 [Information ･･･ Software update ･･･ Network update]

Connecting to internet…

Checking latest version of firmware..

ＴＶ

 [Information ･･･ Software update ･･･ Network update]

Latest version of firmware has been found. 

Firmware update is available. Proeed with update?

ＴＶ

 [Information ･･･ Software update ･･･ Network update]

Downloading latest firmware..

/

HOW TO UPDATE THE SOFTWARE -NETWORK UPDATE-]

1 Turn on the AC power.

2 Insert the upgrading USB flash memory for upgrade into the service slot.

3 Use the Menu button and cursor keys (　　　　 / ▲/▼) ,　Ｃｈ keys (∧/∨) 

of R/C or on the set to select 
 “HOME” > “TV Menu” > “Setup” > “Information” > “Software update” > “USB update”.on OSD menu.

4 If software update file is detected on a network server, the following screen shows up.

For a while, change to the next screen automatically if there is no problem.

Note

・ If not connectable with a network, caution shows up.

Cannot reach the server. Check the network settings and try again.

・ If there is no software update file on a network server or

software update file there is already installed, caution shows up.

Abort

 

ENTER:Enter

5 The caution for update shows up.

Select "Yes" if there is no problem.

Current version

xxxxxxxxxxxx

Latest version

xxxxxxxxxxxx

Estimated update time

xxxxxxxxxxxx

According to the change of the network environment,

 the time actually will change from above one.

Yes

No

6 Software update starts.

Please wait for a while until the bar shows 100%

Note

・ Do not disconnect the network server during updating

Update version

xxxxxxxxxxxx

75%

Abort

7 When all the procedures are completed, the following upgrade success screen shows up.

Select "OK" if there is no problem.

ＴＶ

 [Information ･･･ Software update ･･･ Network update]

Connecting to internet…

Checking latest version of firmware..

ＴＶ

 [Information ･･･ Software update ･･･ Network update]

Latest version of firmware has been found. 

Firmware update is available. Proeed with update?

ＴＶ

 [Information ･･･ Software update ･･･ Network update]

Downloading latest firmware..

/

HOW TO UPDATE THE SOFTWARE -NETWORK UPDATE-]

1 Turn on the AC power.

2 Insert the upgrading USB flash memory for upgrade into the service slot.

3 Use the Menu button and cursor keys (　　　　 / ▲/▼) ,　Ｃｈ keys (∧/∨) 

of R/C or on the set to select 
 “HOME” > “TV Menu” > “Setup” > “Information” > “Software update” > “USB update”.on OSD menu.

4 If software update file is detected on a network server, the following screen shows up.

For a while, change to the next screen automatically if there is no problem.

Note

・ If not connectable with a network, caution shows up.

Cannot reach the server. Check the network settings and try again.

・ If there is no software update file on a network server or

software update file there is already installed, caution shows up.

Abort

 

ENTER:Enter

5 The caution for update shows up.

Select "Yes" if there is no problem.

Current version

xxxxxxxxxxxx

Latest version

xxxxxxxxxxxx

Estimated update time

xxxxxxxxxxxx

According to the change of the network environment,

 the time actually will change from above one.

Yes

No

6 Software update starts.

Please wait for a while until the bar shows 100%

Note

・ Do not disconnect the network server during updating

Update version

xxxxxxxxxxxx

75%

Abort

7 When all the procedures are completed, the following upgrade success screen shows up.

Select "OK" if there is no problem.

ＴＶ

 [Information ･･･ Software update ･･･ Network update]

Connecting to internet…

Checking latest version of firmware..

ＴＶ

 [Information ･･･ Software update ･･･ Network update]

Latest version of firmware has been found. 

Firmware update is available. Proeed with update?

ＴＶ

 [Information ･･･ Software update ･･･ Network update]

Downloading latest firmware..

/

7 When all the procedures are completed, the following upgrade success screen shows up.

Select "OK" if there is no problem.

Note
•  Then get the set started and call the menu - setup - identification to check the main software version.
CAUTION
1) Do not disconnect the network server during updating.
2) Do not turn off the AC power during upgrading.
3) It takes about one minute to the rewriting completion.

Please confirm the upgrade status on the screen becomes 100%.

4) The AC power supply of the set is waited for about 20 seconds until off

(The AC outlet is pulled out) after the upgrade is completed.

USB

1 Turn on the AC power.

 Insert the upgrading USB flash memory for upgrade into the service slot.

3 Use the Menu button and cursor keys (

◄/► / ▲/▼) , P keys (r/s) of R/C or on the set to select

“HOME” > “TV Menu” > “Setup” > “Information” > “Software update” > “USB update” on OSD menu.

 The message (Insert the USB memory device contains the software update file) shows up.

Push OK when if there is no problem.

After a while, if software update file is detected in the USB memory device, the following screen shows up.
Select YES when if there is no problem.

Note
•  If USB memory device isn’t inserted in TV firmly, caution shows up.

Please insert USB memory device firmly.

•  If USB memory device isn’t correctly inserted in TV, caution shows up.

Please insert USB memory device and retry software update.

•  If there are more than two software update files in the USB memory device, caution shows up.

Please insert one file and retry software update.

•  If there is no software update file in the USB memory device, caution shows up.

Please insert the correct file and retry software update.

•  If software update file in the USB memory device doesn’t mutch this model, caution shows up.

(Because Model name is unmatched or check sum error occurs)

Please insert the correct file and retry software update.

•  If software update file in the USB memory device is already installed, caution shows up.

Please reconfirm the software version and reinstall (if necessary)

•  If USB memory device is not formatted by FAT32, caution shows up.

Please format USB memory device by FAT32.

OK

Note

・ Then get the set started and call the menu - setup - identification to

check the main software version.

CAUTION

1) Do not disconnect the network server during updating.
2) Do not turn off the AC power during upgrading.
3) It takes about one minute to the rewriting completion.

Please confirm the upgrade status on the screen becomes 100%.

4) The AC power supply of the set is waited for about 20 seconds until off

(The AC outlet is pulled out) after the upgrade is completed.

HOW TO UPDATE THE SOFTWARE -USB UPDATE-

1 Turn on the AC power.

2 Insert the upgrading USB flash memory for upgrade into the service slot.

3 Use the Menu button and cursor keys (　　　　 / ▲/▼) ,　Ｃｈ keys (∧/∨) 

of R/C or on the set to select 
 “HOME” > “TV Menu” > “Setup” > “Information” > “Software update” > “USB update”.on OSD menu.

4 The message (Insert the USB memory device contains the software update file) shows up.

Push OK when if there is no problem. 

OK

 

ENTER:Enter

5 After a while,  if software update file is detected in the USB memory device, the following screen shows up. 

Select YES when if there is no problem. 

Note

・ If USB memory device isn't inserted in TV firmly, caution shows up.

Please insert USB memory device firmly.

・ If USB memory device isn't correctly inserted in TV, caution shows up.

Please insert USB memory device and retry software update.

・ If there are more than two software update files in the USB memory device, caution shows up.

Please insert one file and retry software update.

・ If there is no software update file in the USB memory device, caution shows up.

Please insert the correct file and retry software update.

・ If software update file in the USB memory device doesn't mutch this model, caution shows up.

(Because Model name is unmatched or check sum error occurs)
Please insert the correct file and retry software update.

・ If software update file in the USB memory device is already installed, caution shows up.

Please reconfirm the software version and reinstall (if necessary)

・ If USB memory device is not formatted by FAT32, caution shows up.

Please format USB memory device by FAT32.

Current version

Update version

xxxxxxxxxxxx

Yes

No

ＴＶ

 [Information ･･･ Software update ･･･ USB update]

Insert the USB memory device containing

 

the software update file.

Software update file is detected

in the USB memory device

start update ?

ＴＶ

 [Information ･･･ Software update ･･･ USB update]

/

system software was succesfully updated

Update version

xxxxxxxxxxxx

OK

Note

・ Then get the set started and call the menu - setup - identification to

check the main software version.

CAUTION

1) Do not disconnect the network server during updating.
2) Do not turn off the AC power during upgrading.
3) It takes about one minute to the rewriting completion.

Please confirm the upgrade status on the screen becomes 100%.

4) The AC power supply of the set is waited for about 20 seconds until off

(The AC outlet is pulled out) after the upgrade is completed.

HOW TO UPDATE THE SOFTWARE -USB UPDATE-

1 Turn on the AC power.

2 Insert the upgrading USB flash memory for upgrade into the service slot.

3 Use the Menu button and cursor keys (　　　　 / ▲/▼) ,　Ｃｈ keys (∧/∨) 

of R/C or on the set to select 
 “HOME” > “TV Menu” > “Setup” > “Information” > “Software update” > “USB update”.on OSD menu.

4 The message (Insert the USB memory device contains the software update file) shows up.

Push OK when if there is no problem. 

OK

 

ENTER:Enter

5 After a while,  if software update file is detected in the USB memory device, the following screen shows up. 

Select YES when if there is no problem. 

Note

・ If USB memory device isn't inserted in TV firmly, caution shows up.

Please insert USB memory device firmly.

・ If USB memory device isn't correctly inserted in TV, caution shows up.

Please insert USB memory device and retry software update.

・ If there are more than two software update files in the USB memory device, caution shows up.

Please insert one file and retry software update.

・ If there is no software update file in the USB memory device, caution shows up.

Please insert the correct file and retry software update.

・ If software update file in the USB memory device doesn't mutch this model, caution shows up.

(Because Model name is unmatched or check sum error occurs)
Please insert the correct file and retry software update.

・ If software update file in the USB memory device is already installed, caution shows up.

Please reconfirm the software version and reinstall (if necessary)

・ If USB memory device is not formatted by FAT32, caution shows up.

Please format USB memory device by FAT32.

Current version

Update version

xxxxxxxxxxxx

Yes

No

ＴＶ

 [Information ･･･ Software update ･･･ USB update]

Insert the USB memory device containing

 

the software update file.

Software update file is detected

in the USB memory device

start update ?

ＴＶ

 [Information ･･･ Software update ･･･ USB update]

/

system software was succesfully updated

Update version

xxxxxxxxxxxx