DOWNLOAD Sharp LC-70UQ10KN (serv.man3) Service Manual ↓ Size: 12.93 MB | Pages: 88 in PDF or view online for FREE

The adjustment process mode menu is listed in Section 5.
Signal generator level adjustment check (Adjustment to the specified level)

•  Composite signal PAL  

   : 0.7Vp-p ± 0.02Vp-p (Pedestal to white level)

•  HDTV signal   

 

: Y level  

: 0.7Vp-p ± 0.02Vp-p (Pedestal to white level)

 

    : PB, PR level   : 0.7Vp-p ± 0.02Vp-p

•  ANALOG PC(RGB) signal  

: RGB    

: 0.7Vp-p ± 0.02Vp-p (Pedestal to white level)

10.1. Entering the adjustment process mode

Enter 

the adjustment process mode according to Section 2.

10.2. PAL signal adjustment

10.3. TUNER adjustment

10.4. SECAM adjustment

10. Video signal adjustment procedure

The adjustment process mode menu is listed in Section 5.
Signal generator level adjustment check (Adjustment to the specified level)

・ Composite signal PAL

: 0.7Vp-p ± 0.02Vp-p (Pedestal to white level)

・ HDTV signal

: Y level           

: 0.7Vp-p ± 0.02Vp-p (Pedestal to white level)

: PB, PR level   

: 0.7Vp-p ± 0.02Vp-p

・ ANALOG PC(RGB) signal   

: RGB ﾚﾍﾞﾙ)     

: 0.7Vp-p ± 0.02Vp-p (Pedestal to white level)

10.1. Entering the adjustment process mode

  Enter the adjustment process mode  according to Section 2.

10.2. PAL signal adjustment 

1

 Setting

  ・Feed the PAL Full-field Colour Bar signal 

 [Signal]

　   (75% colour saturation) to SCART input.

  PAL Full-field Colour Bar

[VIDEO input signal]

 [Terminal]
 EXT1 SCART Video

100% white

Black

2

 Auto adjustment

Adjustment process

 Bring the cursor on [PAL ADJ] and press [OK].

 performance

[PAL ADJ] 

 [PAL ADJ OK] appears when finished.

 page 4/30

* ATTENTION :  Please execute [10.3. TUNER adjustment] afterwards if you adjust [10.2. PAL signal adjustment]  after all adjustments are completed. 

10.3. TUNER adjustment

1

 Setting

 ・ Feed the PAL Split Field colour bar signal (E-12ch) to TUNER.

 [Signal]

 ・ Make sure the PAL colour bar pattern has the sync level of 7:3 with the 

 PAL sprit field colour Bar

    picture level.

 RF signal UV

Signal level: 55 dB μV ± 1dB (75Ω LOAD)

[E-12CH]

 [Terminal]
 TUNER

↑100% white

2

 Auto adjustment

Adjustment process

 Bring the cursor on [ TUNER ADJ] and press [OK]

 performance

[ TUNER ADJ] 

 [TUNER ADJ 　OK] appears when finished.

 page 3/30

  ・Feed the SECAM Full-field Colour Bar signal 

10.4. SECAM adjustment

　   (75% colour saturation) to SCART input.

1

 Setting

  ・Feed the SECAM Full-field Colour Bar signal 

 [Signal]

　   (75% colour saturation) to SCART input.

  SECAM Full-field Colour Bar

[VIDEO input signal]

 [Terminal]
 EXT1 SCART Video

100% white

Black

2

 Auto adjustment

Adjustment process

 Bring the cursor on [SECAM ADJ] and press [OK] 

 performance

[SECAM ADJ] 

[SECAM ADJ OK] appears when finished.

 page 4/30

 Adjustment point 

 Adjustment conditions

Adjustment procedure

 Adjustment point 

 Adjustment conditions

Adjustment procedure

 Adjustment point 

 Adjustment conditions

Adjustment procedure

10. Video signal adjustment procedure

The adjustment process mode menu is listed in Section 5.
Signal generator level adjustment check (Adjustment to the specified level)

・ Composite signal PAL

: 0.7Vp-p ± 0.02Vp-p (Pedestal to white level)

・ HDTV signal

: Y level           

: 0.7Vp-p ± 0.02Vp-p (Pedestal to white level)

: PB, PR level   

: 0.7Vp-p ± 0.02Vp-p

・ ANALOG PC(RGB) signal   

: RGB ﾚﾍﾞﾙ)     

: 0.7Vp-p ± 0.02Vp-p (Pedestal to white level)

10.1. Entering the adjustment process mode

  Enter the adjustment process mode  according to Section 2.

10.2. PAL signal adjustment 

1

 Setting

  ・Feed the PAL Full-field Colour Bar signal 

 [Signal]

　   (75% colour saturation) to SCART input.

  PAL Full-field Colour Bar

[VIDEO input signal]

 [Terminal]
 EXT1 SCART Video

100% white

Black

2

 Auto adjustment

Adjustment process

 Bring the cursor on [PAL ADJ] and press [OK].

 performance

[PAL ADJ] 

 [PAL ADJ OK] appears when finished.

 page 4/30

* ATTENTION :  Please execute [10.3. TUNER adjustment] afterwards if you adjust [10.2. PAL signal adjustment]  after all adjustments are completed. 

10.3. TUNER adjustment

1

 Setting

 ・ Feed the PAL Split Field colour bar signal (E-12ch) to TUNER.

 [Signal]

 ・ Make sure the PAL colour bar pattern has the sync level of 7:3 with the 

 PAL sprit field colour Bar

    picture level.

 RF signal UV

Signal level: 55 dB μV ± 1dB (75Ω LOAD)

[E-12CH]

 [Terminal]
 TUNER

↑100% white

2

 Auto adjustment

Adjustment process

 Bring the cursor on [ TUNER ADJ] and press [OK]

 performance

[ TUNER ADJ] 

 [TUNER ADJ 　OK] appears when finished.

 page 3/30

  ・Feed the SECAM Full-field Colour Bar signal 

10.4. SECAM adjustment

　   (75% colour saturation) to SCART input.

1

 Setting

  ・Feed the SECAM Full-field Colour Bar signal 

 [Signal]

　   (75% colour saturation) to SCART input.

  SECAM Full-field Colour Bar

[VIDEO input signal]

 [Terminal]
 EXT1 SCART Video

100% white

Black

2

 Auto adjustment

Adjustment process

 Bring the cursor on [SECAM ADJ] and press [OK] 

 performance

[SECAM ADJ] 

[SECAM ADJ OK] appears when finished.

 page 4/30

 Adjustment point 

 Adjustment conditions

Adjustment procedure

 Adjustment point 

 Adjustment conditions

Adjustment procedure

 Adjustment point 

 Adjustment conditions

Adjustment procedure

10. Video signal adjustment procedure

The adjustment process mode menu is listed in Section 5.
Signal generator level adjustment check (Adjustment to the specified level)

・ Composite signal PAL

: 0.7Vp-p ± 0.02Vp-p (Pedestal to white level)

・ HDTV signal

: Y level           

: 0.7Vp-p ± 0.02Vp-p (Pedestal to white level)

: PB, PR level   

: 0.7Vp-p ± 0.02Vp-p

・ ANALOG PC(RGB) signal   

: RGB ﾚﾍﾞﾙ)     

: 0.7Vp-p ± 0.02Vp-p (Pedestal to white level)

10.1. Entering the adjustment process mode

  Enter the adjustment process mode  according to Section 2.

10.2. PAL signal adjustment 

1

 Setting

  ・Feed the PAL Full-field Colour Bar signal 

 [Signal]

　   (75% colour saturation) to SCART input.

  PAL Full-field Colour Bar

[VIDEO input signal]

 [Terminal]
 EXT1 SCART Video

100% white

Black

2

 Auto adjustment

Adjustment process

 Bring the cursor on [PAL ADJ] and press [OK].

 performance

[PAL ADJ] 

 [PAL ADJ OK] appears when finished.

 page 4/30

* ATTENTION :  Please execute [10.3. TUNER adjustment] afterwards if you adjust [10.2. PAL signal adjustment]  after all adjustments are completed. 

10.3. TUNER adjustment

1

 Setting

 ・ Feed the PAL Split Field colour bar signal (E-12ch) to TUNER.

 [Signal]

 ・ Make sure the PAL colour bar pattern has the sync level of 7:3 with the 

 PAL sprit field colour Bar

    picture level.

 RF signal UV

Signal level: 55 dB μV ± 1dB (75Ω LOAD)

[E-12CH]

 [Terminal]
 TUNER

↑100% white

2

 Auto adjustment

Adjustment process

 Bring the cursor on [ TUNER ADJ] and press [OK]

 performance

[ TUNER ADJ] 

 [TUNER ADJ 　OK] appears when finished.

 page 3/30

  ・Feed the SECAM Full-field Colour Bar signal 

10.4. SECAM adjustment

　   (75% colour saturation) to SCART input.

1

 Setting

  ・Feed the SECAM Full-field Colour Bar signal 

 [Signal]

　   (75% colour saturation) to SCART input.

  SECAM Full-field Colour Bar

[VIDEO input signal]

 [Terminal]
 EXT1 SCART Video

100% white

Black

2

 Auto adjustment

Adjustment process

 Bring the cursor on [SECAM ADJ] and press [OK] 

 performance

[SECAM ADJ] 

[SECAM ADJ OK] appears when finished.

 page 4/30

 Adjustment point 

 Adjustment conditions

Adjustment procedure

 Adjustment point 

 Adjustment conditions

Adjustment procedure

 Adjustment point 

 Adjustment conditions

Adjustment procedure

10.5. ADC adjustment (Component 15K)

1

 Setting

  ・Feed the COMPONENT 15K 100% full field colour bar signal 

 [Signal]

　(100% colour saturation) to EXT3 COMPONENT IN.

 COMP15K, 50Hz(576i/50Hz)
 100% Full field colour bar

 [Terminal]
 EXT3 COMPONENT 

100% white

Black

2

 Auto adjustment

Adjustment process

 Bring the cursor on [COMP15k ALL ADJ] and press [OK]

 performance

 [COMP15k ALL ADJ] 

 [COMP15K ALL ADJ OK] appears when finished.

 page 6/30

10.6. ADC adjustment (Component 33K)

1

 Setting

  ・Feed the COMPONENT 33K 100% full field colour bar signal 

 [Signal]

　(100% colour saturation) to EXT3 COMPONENT IN.

 COMP33K, 50Hz (1080i/50Hz)
 100% Full field colour bar 

 [Terminal]
 EXT3 COMPONENT 

100% white

Black

2

 Auto adjustment

Adjustment process

 Bring the cursor on [HDTV ADJ] and press [OK].

 performance

[HDTV ADJ]

 [HDTV ADJ OK] appears when finished.

 page 7/30

10.7. PC signal adjustment (ANALOG D-Sub 15pin)

1

 Setting

  ・Feed the XGA 60Hz 100% full field colour bar signal 

 [Signal]

　 (100% colour saturation)to PC IN.

 XGA, 60Hz
 100% Full Field Colour Bar

 [Terminal]
 PC IN

100% white

Black

2

 Auto adjustment

Adjustment process

 Bring the cursor on [ANALOG PC ADJ] and press [OK]

 performance

[ANALOG PC ADJ] menu

 [ANALOG PC ADJ OK] appears when finished.

 page 8/30

10.8. RGB (SCART) adjustment (RGB 15K)

1

 Setting

  ・Feed the RGB 15k 50Hz 100% full field colour bar signal 

 [Signal]

　  (100% colour saturation)to EXT1 SCART IN.

 RGB 15K, 50Hz
 100% Full field colour bar

 [Terminal]
 EXT1 SCART RGB IN

100% white

Black

2

 Auto adjustment

Adjustment process

 Bring the cursor on [SCART RGB ADJ] and press [OK]

 performance

[SCART RGB ADJ]  menu

 [SCART RGB ADJ OK] appears when finished.

 page 9/30

 Adjustment point 

 Adjustment conditions

Adjustment procedure

 Adjustment conditions

 Adjustment conditions

 Adjustment point 

Adjustment procedure

 Adjustment point 

 Adjustment conditions

Adjustment procedure

Adjustment procedure

 Adjustment point 

10.5. ADC adjustment (Component 15K)

10.6. ADC adjustment (Component 33K)

10.7. PC signal adjustment (ANALOG D-Sub 15 pin)

10.8. RGB (SCART) adjustment (RGB 15K)

Case1 : WB value is SAME compared to “before” fix and “after” fix.

Ex) Replacement parts: Main PWB (You can “power on” TV and video picture displays)

Before changing Main Board
1: Enter the adjustment process mode and go to page where it has “USB BACKUP” on the page 29/30.
2: Insert the USB Memory into the service socket.
3: Press Enter ,return “BackUp OK”.
4: Written AQUOS_DATA.dat into USB Memory.

After changing Main Board
1: Entering the adjustment process mode  and go to page where it has “USB RESTORE”.

(Same page as where “USB BACKUP” was.)

2: Insert the USB Memory written AQUOS_DATA.dat into the service socket.
3: Press Enter
4: After a few seconds , return “Restore OK”
5:Escape “Adjustment process mode” then detach USB memory.

Case2 : WB value is more different than before changing parts

Ex) Replacement parts: Main PWB (New repair board, such as NO data)
 or Change LCD module unit.

11. White Balance Adjustment

Case1 : WB value is SAME compared to “before” fix and “after” fix.

Ex) Replacement parts: Main PWB (You can “power on” TV and video picture displays)

Before changing Main Board

1: Enter the adjustment process mode and go to page where it has "USB BACKUP" on the page 29/30.
2: Insert the USB Memory into the service socket.
3: Press Enter ,return "BackUp OK"
4: Written AQUOS_DATA.dat into USB Memory.

After changing Main Board

1: Entering the adjustment process mode  and go to page where it has "USB RESTORE".

(Same page as where "USB BACKUP" was.)

2: Insert the USB Memory written AQUOS_DATA.dat into the service socket.
3: Press Enter
4: After a few seconds , return "Restore OK"
5: Escape “Adjustment process mode” then detach USB memory.

Case2 : WB value is more different than before changing parts

Ex) Replacement parts: Main PWB (New repair board, such as NO data)

or
Change LCD module unit

ITEM

CONDITION

PROCEDURE

1 Setting

Brightness：MAX (+16)
AV MODE: DYNAMIC
Active Backlight: off
OPC: off

*Set the luminance 
meter on the center
of the screen

Regarding the details of white balance adjustment procedure, 
refer to white balance adjustment spec for “Kameyama model version 1.9”.

1. Confirm the TV set condition.
2. Connect the white balance jig.
3. Display the Adjustment mode screen via RS-232C command.

[ Target location for adjustment]

2 Auto

Adjustment

[Command]
Adjustment mode
KRSW0001
KKT10037

Setting
KYOF0000
OSDS0001
SBSL0016

Multi point adj.
MSET0011

 Initialization of the  adj. 
value
MSET0012
Mode1:QPMD0001

[Adjustment Quattron Pro drive Mode]
 AV mode Dynamic : Quattron Pro Drive : Mode1
 AV mode MovieTHX: Quattron Pro Drive : Mode1

[ Adjustment procedure ]
1. 
Using R/C, set the LCD TV to adjustment mode.

2. 
Set the specified level for point 7, and measure the luminance.
Set the R/G/B initial value tentatively, then treat the strongest color of R/G/B 
as fixed value, adjust remained other.
2 colors by reducing value to get “target value” of point 7.
  R＞G  Ye=G*1.05
When the value of Ye over an initial value ( 928 ),set value 928.
  R≦G  Ye=R*1.05
When the value of Ye over an initial value ( 928 ),set value 928.
Set the value of Ye which was calculated from the above conditional expression
in MG7YXXXX.
Adjust R/G/B repeatedly until converging to “target value”.

Point 7
LEV70232  
MG7G****
MG7B****
MG7R****
MG7*****

Point 6
LEV60196  
MG6G****
MG6B****
MG6R****
MG6*****

Point 5
LEV50156 
MG5G****
MG5Y****
MG5B****
MG5R****

Point 4
LEV40108
MG4G****
MG4Y****
MG4B****
MG4R****

Point 3
LEV30076 
MG3G****
MG3Y****
MG3B****
MG3R****

Point 2
LEV20048  
MG2G****
MG2Y****
MG2B****
MG2R****

3. 
Set the specified level for point 6, and measure the luminance.
Set the revised value of G
(784 * G level of point 7 / 928) (a fraction is rounded off.),
and correction value of Ye(784 * Ye level of point 7 / 928)  adjust the value of 
R/B to “target value” of point 6.

4. 
Set the specified level for point5, and measure the luminance.
Set the revised value of G
(624 * G level of point7/ 928) (a fraction is rounded off),
and correction value of Ye(624 * Ye level of point 7/ 928) adjust the value of 
R/B to “target value” of point 6.

5. 
Set the specified level for point4, and measure the luminance.
Set the revised value of G
(432 * G level of point 7/ 928) (a fraction is rounded off),
and correction value of Ye(432 * Ye level of point7 / 928) adjust the value of 
R/B for “target value” of point4.

6. 
Set the specified level for point 3, and measure the luminance.
Set the revision value of G
(304 * G level of point 7 / 928) (a fraction is rounded off),
and correction value of Ye(304 * Ye level of point 7/ 928) adjust the value of 
R/B to “target value” of point 3

7. 
Set the specified level for point 2, and measure the luminance.
Set the revised value of G
(192 * G level of point 7 / 928) (a fraction is rounded off),
and correction value of Ye(192 * Ye level of point 7 / 928) adjust the value of 
R/B to ”target value” of point2.

8. 
Set the specified level for point 1, and measure the luminance.
Set the revised value of G
(80 * G level of point7 / 928) (a fraction is rounded off),
and correction value of Ye(80* Ye level of point 7 / 928) 
The initial value of the point 1*( The adjustment value of R of the point 
2/specified level for point2)*R_GAIN(a fraction is rounded off),
and The initial value of the point 1*( The adjustment value of R of the point 
2/specified level for point2)*R_GAIN(a fraction is rounded off)setting the R/B.

The R,B gain of the point 1
     Dynamic mode : R_GAIN=0.981  B_GAIN=1.149
     Movie THX mode : R_GAIN=0.990  B_GAIN=1.019

Point 1
LEV10020 
MG1G****
MG1Y****
MG1B****
MG1R****

W/B adj. value data
input
MSET0030

9 
Write the value of W/B adjustment by inputting command
 “MSET0030”.

*Initial value of RGBYe at Point 7 = “928”
 *Initial value of RGB at Point 1-6
= correction value of G of each point
*Initial value of Ye at Point 1-6
= correction value of Ye of each point

[Caution]
 To measure the chromaticity and luminance , please wait more
 than the following delay time from return marks of “OK”.
 Because there is a delay time to output the pattern after
 executing a test pattern output command.
　 
* Picture delay time : 70ms
  (the maximum total delay of the main microcomputer
 and LCD controller)

[ Target value for adjustment ]
 The target value applies correspondingly to the teaching set.
 And read the target value from the marking position.

[ Reference value for adjustment ]
 Equipment : Luminance meter [Minolta CA-210]