DOWNLOAD Sharp LC-70UQ10KN (serv.man3) Service Manual ↓ Size: 12.93 MB | Pages: 88 in PDF or view online for FREE

7/30

1

HDTV ADJ

Enter

HDTV video level adjustment

2

HDTV Y GAIN

xxx

HDTV Y GAIN adjustment value

3

HDTV CB GAIN

xxx

HDTV Cb adjustment value

4

HDTV CR GAIN

xxx

HDTV Cr adjustment value

5

HDTV Y OFFSET

xxx

HDTV Y OFFSET adjustment value

6

HDTV CB OFFSET

xxx

HDTV Cb OFFSET adjustment value

7

HDTV CR OFFSET

xxx

HDTV Cr OFFSET adjustment value

8

HDTV A_CLAMP

xxx

HDTV CLAMP

8/30

1

ANALOG PC ADJ

Enter

DVI ANALOG video level adjustment

2

R OFFSET

xxx

R CUTOFF adjustment value

3

G OFFSET

xxx

G CUTOFF adjustment value

4

B OFFSET

xxx

B CUTOFF adjustment value

5

R GAIN

xxx

R DRIVE adjustment value

6

G GAIN

xxx

G DRIVE adjustment value

7

B GAIN

xxx

B DRIVE adjustment value

8

RGB A_CLAMP

xxx

RGB CLAMP

9/30

1

SCART RGB ADJ

Enter

SCART RGB level adjustment

2

SCART RGB ADJ (FASTSW)

Enter

SCART RGB ADJ (FASTSW) adjustment

3

SCART R CUTOFF

xxx

SCART R CUTOFF adjustment value

4

SCART G CUTOFF

xxx

SCART G CUTOFF adjustment value

5

SCART B CUTOFF

xxx

SCART B CUTOFF adjustment value

6

SCART R GAIN

xxx

SCART R GAIN adjustment value

7

SCART G GAIN

xxx

SCART G GAIN adjustment value

8

SCART B GAIN

xxx

SCART B GAIN adjustment value

9

SCART A_CLAMP

xxx

SCART RGB CLAMP

10/30

1

VCOM ADJ 

xxx

Common bias adjustment

11/30

1

LEV1

xxx

2

LEV2

xxx

3

LEV3

xxx

4

LEV4

xxx

5

LEV5

xxx

6

LEV6

xxx

7

LEV7

xxx

12/30

1

MG1R

xxx

WB adjustment Point 1, R adjustment value

2

MG1G

xxx

WB adjustment Point 1, Gadjustment value

3

MG1B

xxx

WB adjustment Point 1, B adjustment value

4

MG1Y

xxx

WB adjustment Point 1, Y adjustment value

5

MG2R

xxx

WB adjustment Point 2, R adjustment value

6

MG2G

xxx

WB adjustment Point 2, Gadjustment value

7

MG2B

xxx

WB adjustment Point 2, B adjustment value

8

MG2Y

xxx

WB adjustment Point 2, Y adjustment value

9

MG3R

xxx

WB adjustment Point 3, R adjustment value

10

MG3G

xxx

WB adjustment Point 3, Gadjustment value

11

MG3B

xxx

WB adjustment Point 3, B adjustment value

12

MG3Y

xxx

WB adjustment Point 3, Y adjustment value

13/30

1

MG4R

xxx

WB adjustment Point 4, R adjustment value

2

MG4G

xxx

WB adjustment Point 4, Gadjustment value

3

MG4B

xxx

WB adjustment Point 4, B adjustment value

4

MG4Y

xxx

WB adjustment Point 4, Y adjustment value

5

MG5R

xxx

WB adjustment Point 5, R adjustment value

6

MG5G

xxx

WB adjustment Point 5, Gadjustment value

7

MG5B

xxx

WB adjustment Point 5, B adjustment value

8

MG5Y

xxx

WB adjustment Point 5, Y adjustment value

9

MG6R

xxx

WB adjustment Point 6, R adjustment value

10

MG6G

xxx

WB adjustment Point 6, Gadjustment value

11

MG6B

xxx

WB adjustment Point 6, B adjustment value

12

MG6Y

xxx

WB adjustment Point 6, Y adjustment value

14/30

1

MG7R

xxx

WB adjustment Point 7, R adjustment value

2

MG7G

xxx

WB adjustment Point 7, Gadjustment value

3

MG7B

xxx

WB adjustment Point 7, B adjustment value

4

MG7Y

xxx

WB adjustment Point 7, Y adjustment value

15/30

1

LO R 1

xxx

2

LO G 1

xxx

3

LO B 1

xxx

4

LO Y 1

xxx

5

LO R 2

xxx

6

LO G 2

xxx

7

LO B 2

xxx

8

LO Y 2

xxx

9

LO R 3

xxx

10

LO G 3

xxx

11

LO B 3

xxx

12

LO Y 3

xxx

16/30

1

LO R 4

xxx

2

LO G 4

xxx

3

LO B 4

xxx

4

LO Y 4

xxx

5

LO R 5

xxx

6

LO G 5

xxx

7

LO B 5

xxx

8

LO Y 5

xxx

9

LO R 6

xxx

10

LO G 6

xxx

11

LO B 6

xxx

12

LO Y 6

xxx

17/30

1

LO R 7

xxx

2

LO G 7

xxx

3

LO B 7

xxx

4

LO Y 7

xxx

5

CTEMP SELECT

CTEMP HI

18/30

1

MODE SELECT 

Factory

2

POS MIN

WB IN

3

POS MID1

xxx

4

POS MID2

xxx

5

POS MID3

xxx

6

POS MID4

xxx

7

POS MID5

xxx

8

POS MID6

xxx

9

POS MID7

xxx

10

POS MAX

xxx

19/30

1

CD MIN

xxx

2

CD MID1

xxx

3

CD MID2

xxx

4

CD MID3

xxx

5

CD MID4

xxx

6

CD MID5

xxx

7

CD MID6

xxx

8

CD MID7

xxx

9

CD MAX

xxx

20/30

1

CALC

OFF

2

RESET

OFF

3

VAL1

xxx

4

VAL2

xxx

5

VAL3

xxx

6

VAL4

xxx

7

VAL5

xxx

8

VAL6

xxx

9

VAL7

xxx

10

GAMMA ADJ TEMP

xxx

21/30

1

MONITOR TIME OUT

ON

Monitor and the main communication time-out setting

2

MONITOR MAX TEMP

xxx

MONITOR MAX temperature setting

3

MONITOR EEP READ / WRITE

WRITE

MONITOR EEPROM READ/WRITE Setting/execution

4

MONITOR EEP ADR

0x  0

MONITOR EEPROM arbitrary addressing

5

MONITOR EEP DATA

0x  0

MONITOR EEPROM arbitrary data specification

22/30

1

LCD TEST PATTERN

Pattern with built-in LCD controller display

2

LCD TEST PATTERN1

OFF

3

LCD TEST PATTERN2

OFF

4

LCD TEST PATTERN3

NOT SUPPORT

5

LCD TEST PATTERN4

NOT SUPPORT

23/30

1

BOARD

2

LVM

3

LSE1(3D)

4

LSE1(2D)

5

LSE2(2D)

6

FRC MASTER FW

7

FRC SLAVE FW

8

TCON(2D MPD OFF MASTER)]

9

TCON(3D MASTER)

24/30

1

3DHDMI FPGA Version

xxxxx

2

2D→3D FPGA Version

xxxxx

3

3D LED BRIGHTNESS

xxxxx

4

3D IR EMITTER CONTROL

ON

25/30

1

CROSSTALK ADJ MODE

Enter

2

CROSSTALK TH1

3

CROSSTALK TH2

4

CROSSTALK TH3

5

CROSSTALK TH4

6

CROSSTALK GAIN1

7

CROSSTALK GAIN2

8

CROSSTALK GAIN3

26/30

1

WIFI SSID 2.4GHz

xxxxx

2

WIFI SSID 5  GHz

xxxxx

3

WIFI RSSI 2.4GHz

xxxxx

4

WIFI RSSI 5  GHz

xxxxx

5

WIFI TIME 5 GHz

xxxxx

6

WIFI RSSI TEST

xxxxx

7

WIFI RSSI RESULT

xxxxx

27/30

1

READ/WRITE

READ

Read/Write

2

SLAVE/ADDRESS

SLAVE0

Slave address

3

REGISTER ADDRESS

0x 0
0x 0

Register address

4

WRITE DATA

0x 0
0x 0

Writing data

5

READ DATA

0x 0
0x 0

Reading data

28/30

1

RF AGC BG

xx

RF-AGC BG adjustment execution

2

RF AGC DK

xx

RF-AGC DKG adjustment execution

3

RF AGC I

xx

RF-AGC I adjustment execution

4

RF AGC L/L'

xx

RF-AGC L/L' adjustment execution

5

CI+ AUTHENTICATION

xx

29/30

1

ERROR STANDBY CAUSE1

NO RECORD

ERROR STANDBY CAUSE

2

ERROR STANDBY CAUSE2

NO RECORD

3

ERROR STANDBY CAUSE3

NO RECORD

4

ERROR STANDBY CAUSE4

NO RECORD

5

ERROR STANDBY CAUSE5

NO RECORD

6

STANDBY CAUSE RESET

OFF

Reset stand by cause.

7

USB BACKUP

Enter

8

USB RESTORE

Enter

30/30

1

EEP SAVE

OFF

Writing setting values to EEPROM.

2

EEP RECOVER

OFF

Reading setting values from EEPROM.

3

MONITOR ERROR CAUSE RESET

OFF

Reset of monitor error cause

4

MODEL NAME

UQ10E

MODEL NAME

5

PANEL SIZE

xx

Panel size setting.

6

VERUP FLAG ENABLE

Enter

Verup Flag

7

PANEL LIMIT

ON

PANEL LIMIT

8

PANEL RANGE LIMIT

xxx

PANEL RANGE LIMIT

9

SHORT CHECK MODE

Enter

Check LED Back light

10

SHORT CHECK CURRENT

xx

11

PRODUCT EEP ADR

0x 0

Don't touch when serving (for producer of factory)

12

PRODUCT EEP DATA

0x 0

Don't touch when serving (for producer of factory)

13

PRODUCT FACTORY

xxx

Don't touch when serving (for producer of factory)

14

TEST NETWORK UPDATE

NO

6.1. NORMAL STANDBY CAUSE (Page 1/30)

Display of a cause (code) of the last standby.
The cause of the last standby is recorded in EEPROM whenever it is possible.

Checking this code will be useful in finding a problem when you repair the troubled set.

6.2. EEP SAVE (Page 30/30)

Storage of EEP adjustment value.

6.3. EEP RECOVER (Page 30/30)    

Retrieval of EEP adjustment value from storage area.

6.4. MONITOR ERR CAUSE (Page 1/30)

Display of a cause (code) of Error from Monitor microcomputer. 
The cause of Error is recorded in EEPROM whenever it is possible.

Checking this code will be useful in finding a problem when you repair the troubled set.



This displays Error code and time when the error occurred. 

The latest error is displayed  on “ 1)”

The error that happens ahead of “1)” is displayed on “2)”. 



The character depends on the way how to acquire Time Information.

 T: Time is acquired from digital broadcasting.

This doesn’t contain “Time offset” which is considered a time difference and Daylight-Saving Time, etc....

U: Time is acquired from analog broadcasting (teletext).
B: Accumulation time of Backlight.
In the case that Time information cannot be acquired, “B” is displayed 

.

Example)   In this example, it is shown that the error occurred 3 times.

1) 16 T07/01/01 12:03
Error code: 16 (lamp error)   

    

 It is latest Error.

Time : 07/01/01 12:03     

 Time is acquired from digital broadcasting.

 

       

 Time is UTC which doesn’t have Time offset.

2) 16 U01/01/01 04:07
Error code: 16 (lamp error)  

    



 It is Error that happens ahead of “1)”. 

Time : 07/01/01 04:07     

 Time is acquired from analogue broadcasting.

3) 16 B00000004:11
Error code: 16 (lamp error)  

    



  It is Error that happens ahead of “2)”. 

Accumulation time : It is displayed that 4:11 have passed after Backlight driving.

4) 00 000000000No error (“00” shows that the error is not occurred.)

7.1. Function
This LCD color TV set incorporates a Lamp error detection feature that automatically turns off the power for safety 
under     abnormal lamp or lamp circuit conditions. If by any chance anything is wrong with the lamp or lamp circuit or 
if the lamp error detection feature is activated for some reason, the following will result.

1) The power is interrupted in about 500ms after it is turned on.     

(A central icon on the front of the TV flash on and off. : ON for 400ms and OFF for 1600ms.).

2) If the above phenomenon 1) occurs 5 times, it becomes impossible to turn on the power.  

(A central icon keep flashing on/off.)

7.2. Measures

1) Set the lamp error detection to OFF.

Enter the adjustment process mode, referring to “2. Entering and exiting the adjustment process mode.”

The adjustment process mode can ignore “5 times count”, so if the above phenomenon 1) occurs 1~4 times, the 
lamp will go out.
If Lamp Error detection pin [22pin of PD : P3801 / 19pin of IC2002 ] is “High” by a trouble with the lamp and lamp 
circuit, it can boot-up by the adjustment process mode.
Please execute  

Unplug the AC power cord of running TV set to force off the power.

While holding down the “VOL (+)” and “P ( 

s

 )” keys on the set at once, plug in the AC power cord to turn on 

the power.

After a central icon flash off, separate the fingers from key on the set .

Then, you can check the operation to see if the lamp and lamp circuit are in trouble.
If you fail boot-up, retry the procedure.