DOWNLOAD Sharp LC-70UQ10KN (serv.man3) Service Manual ↓ Size: 12.93 MB | Pages: 88 in PDF or view online for FREE

Model
LC-70UQ10KN (serv.man3)
Pages
88
Size
12.93 MB
Type
PDF
Document
Service Manual
Brand
Device
TV / LCD
File
lc-70uq10kn-sm3.pdf
Date

Sharp LC-70UQ10KN (serv.man3) Service Manual ▷ View online

1
LC-60UQ10
LC-70UQ10
MODELS
LC-60UQ10E  
LC-60UQ10EN
LC-60UQ10KN
LC-70UQ10E
LC-70UQ10EN
LC-70UQ10KN
SERVICE MANUAL
  LED LCD 
COLOUR TELEVISION
160mm
125mm
100mm
80mm
63mm
50mm
40mm
31.5mm
25mm
20mm
A-data-1
sharp.
Corporate Trademark
SHARP  CORPORATION
In the interests of user safety (required by safety 
regulations in some countries) the set should be re-
stored to its original condition and only parts identical 
to those specified should be used.
CONTENTS
ELECTRICAL SPECIFICATIONS ...............................................................................  2
IMPORTANT SERVICE SAFETY PRECAUTIONS .........................................................................   3
OPERATION MANUAL ....................................................................................................................   6
DIMENSIONS .................................................................................................................... 19
REMOVING OF MAJOR PARTS .....................................................................................................  21
SERVICE ADJUSTMENTS .............................................................................................................  29
HOW TO UPDATE THE SOFTWARE........................................................................................ 51
TROUBLE SHOOTING
 
...................................................................................................................
 
54 
MAJOR ICs INFORMATION
 ............................................................................................................
 
72
OVERALL WIRING DIAGRAM ........................................................................................................
 
73 
BLOCK DIAGRAMS ......................................................................................................................  75
PARTS GUIDE ......................................................................................................................  77
                       Issued: 27
th 
February 2014
SE1SLC60UQ10E
DRAFT 2
1st Edition
2
LC-60UQ10
LC-70UQ10
ELECTRICAL SPECIFICATIONS
Specifications
Item
Model: 
   LC-70UQ10E     LC-60UQ10E
   LC-70UQ10EN   LC-60UQ10EN
   LC-70UQ10KN   LC-60UQ10KN
LCD panel
177 cm (70o) X-Gen panel
152 cm (60o) X-Gen panel
Resolution
1,920 x 1,080 x 4 dots
Video colour system
PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60
TV function TV-standard
Analogue
CCIR (B/G, I, D/K, L/L’)
Digital
DVB-T (2K/8K OFDM),  DVB-S/S2
DVB-T2 (1K/2K/4K/8K/ 
16K/32K OFDM), DVB-C 
Receiving 
channel
VHF/UHF
IR A ch—E69 ch (Digital), E2—E69 ch, F2—F10 ch, I21—I69 ch, IR A—IR J ch
CATV
Hyper-band, S1—S41 ch
Satellite
950—2150 MHz*
1
TV-tuning system
Auto Preset 999 ch (non-Nordic [DTV])
Auto Preset 9999 ch (Nordic [DTV])
Auto Preset 99 ch (ATV), Auto Label
Auto Sort
Auto Preset 9999 ch
Stereo/Bilingual
A2/NICAM
Audio amplifier
10 W x 2/15 W x 1
Speaker
(150 mm x 32 mm) x 2/Ø 80 mm x 1
Terminals
Antenna
VHF/UHF
75 q Din type (analogue & digital) 
Satellite
75 q F type (DVB-S/S2)
RS-232C
D-sub 9 pin male connector
EXT 1
SCART (AV input, Y/C input, RGB input, TV output)
EXT 2
RCA pin
 
(Component /Video/Audio L/R input)
PC
mini D-sub 15 pin
HDMI 1 (EXT 3)
HDMI (HDCP2.2)
HDMI 2 (EXT 4)
HDMI
HDMI 3 (EXT 5)
HDMI (ARC)
HDMI 4 (EXT
 
6)
HDMI (MHL)
USB 1
USB (DC 5 V, 500 mA)
USB 2 (HDD)
USB (DC 5 V, 1000 mA)
USB 3 
USB (DC 5 V, 500 mA)
ETHERNET 
Network connector
HDMI 2/PC AUDIO (L/R)
Ø 3.5 mm jack*
2
DIGITAL AUDIO OUTPUT
Optical S/PDIF digital audio output
C. I. (Common Interface)
EN50221, R206001, CI Plus specification
OUTPUT/Headphones
RCA pin (AUDIO L/R)/Ø 3.5 mm jack (audio output)
SD CARD
SD/SDHC memory card
OSD language
Arabic, Chinese, Czech, Danish, Dutch, English, Estonian, Finnish, French, German, Greek, 
Hungarian, Hebrew, Italian, Latvian, Lithuanian, Norwegian, Polish, Portuguese, Romanian, 
Russian, Slovak, Slovene, Spanish, Swedish, Turkish, Ukrainian
Power requirement
AC 220_240 V, 50 Hz
Power consumption
70o :  249W (0.15W Standby*
3
)
60o :  193W (0.15W Standby*
3
)
Weight
70o :  42.5 kg (without stand)
 
48.5 kg (with stand)
60o :  32.5 kg (without stand)
 
38.5 kg (with stand)
Operating temperature
0 °C to e 40 °C
 
I
The satellite channel’s frequency may vary according to satellites and antennas.
 
J
The HDMI 2 and PC terminals can both use the same audio input terminal.
 
K
Standby power consumption applies when the TV is set to not receive EPG data.
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement 
without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from 
these values in individual units.
3
LC-60UQ10
LC-70UQ10
LC-20B5E
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
DVM
AC SCALE
1.5k ohm
10W
0.15 µF
TEST PROBE
SAFETY NOTICE
Many electrical and mechanical parts in LCD television have special safety-related characteristics.
These characteristics are often not evident from visual inspection, nor can protection afforded by them be necessarily 
increased by using replacement components rated for higher voltage, wattage, etc.
Replacement parts which have these special safety characteristics are identified in this manual; electrical components 
having such features are identified by    “    “.
For continued protection, replacement parts must be identical to those used in the original circuit.
The use of a substitute replacement parts which do not have the same safety characteristics as the factory recommended 
replacement parts shown in this service manual, may create shock, fire or other hazards.
IMPORTANT SERVICE SAFETY PRECAUTION
Service work should be performed only by qualified service technicians who are thoroughly familiar with all 
safety checks and the servicing guidelines which follow:
WARNING
1. For continued safety, no modification of any circuit should be attempted.
2. Disconnect AC power before servicing.
BEFORE RETURNING THE RECEIVER (Fire & Shock Hazard)
Before returning the receiver to the user, perform the following safety checks:
1. Inspect all lead dress to make certain that leads are not pinched, and check that hardware is not lodged between the 
chassis and other metal parts in the receiver.
2. Inspect all protective devices such as non-metallic control knobs, insulation materials, cabinet backs, adjustment and 
compartment covers or shields, isolation resistor-capacitor networks, mechanical insulators, etc.
3. To be sure that no shock hazard exists, check for leakage current in the following manner. 
• Plug the AC cord directly into a 220~240 volt AC outlet. (Do not use an isolation transformer for this test).
•Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in series with all exposed metal 
cabinet parts and a known earth ground, such as electrical conduit or electrical ground connected to an earth ground.
• A true RMS reading multimeter should be used for this test, especially where the equipment uses a switch mode 
power supply which may result in very non-sinusoidal leakage current.
• Use an AC voltmeter having with 5000 ohm per volt, or higher, sensitivity or measure the AC voltage drop across 
the resistor.
• Connect the resistor connection to all exposed metal parts having a return to the chassis (antenna, metal cabinet, 
screw heads, knobs and control shafts, escutcheon, etc.) and measure the AC voltage drop across the resistor.
All checks must be repeated with the AC cord plug connection reversed. (If necessary, a nonpolarized adaptor plug must 
be used only for the purpose of completing these checks.)
Any reading of 1.05V peak (this corresponds to 0.7 mA. peak AC.) or more is excessive and indicates a potential shock 
hazard which must be corrected before returning the monitor to the owner.
!
  CAUTION: FOR CONTINUED PROTECTION AGAINST A RISK OF
  FIRE REPLACE ONLY WITH SAME TYPE  F7001 (T 5A H / 250V)
4
LC-60UQ10
LC-70UQ10
e:
Indicates lead-free solder of tin, silver and copper.
L
F a
PRECAUTIONS FOR USING LEAD-FREE SOLDER
1 Employing lead-free solder
“ALL  PWB” of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the 
PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder.
Example:
2 Using lead-free wire solder
When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead 
wire solder may cause damage or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40°C, we recommend you to 
use a dedicated soldering bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our 
service station or service branch in your area.
3 Soldering
As the melting point of lead-free solder (Sn-Ag-Cu) is about 220°C which is higher than the conventional lead solder by 
40°C, and as it has poor solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended 
period of time. However, Since the land may be peeled off or the maximum heat-resistance temperature of parts may be 
exceeded, remove the bit from the PWB as soon as you confirm the steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and 
off the power of the bit as required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every 
use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing.
Indicates lead-free solder of tin, silver and nickel.
L
F n
Sn-Ag-Ni
Page of 88
Display

Sharp LC-70UQ10KN (serv.man3) Service Manual ▷ Download

  • DOWNLOAD Sharp LC-70UQ10KN (serv.man3) Service Manual ↓ Size: 12.93 MB | Pages: 88 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sharp LC-70UQ10KN (serv.man3) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp LC-70UQ10KN (serv.man3) LCD. Information contained in Sharp LC-70UQ10KN (serv.man3) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.