Sharp LC-40LE361E (serv.man2) User Manual / Operation Manual ▷ View online
English - 4 -
WARNING
To prevent the spread of fire, keep
To prevent the spread of fire, keep
candles or other open flames away
from this product at all times.
Power Source
The TV set should be operated only from a 220-240V
AC, 50Hz outlet. Ensure that you select the correct
voltage setting for your convenience.
Power Cord
Do not place the set, a piece of furniture, etc. on the
power cord (mains lead) or pinch the cord.
Handle the power cord by the plug. Do not unplug the
Handle the power cord by the plug. Do not unplug the
appliance by pulling from the power cord and never
touch the power cord with wet hands as this could
cause a short circuit or electric shock. Never make a
knot in the cord or tie it with other cords. The power
cords should be placed in such a way that they are
not likely to be stepped on. A damaged power cord
can cause fire or give you an electric shock. When it
is damaged and needs to be replaced, it should be
done by qualified personnel.
Moisture and Water
Do not use this device in a humid and damp place
(avoid the bathroom, the sink in the kitchen, and near
the washing machine). Do not expose this device to
rain or water, as this may be dangerous and do not
place objects filled with liquids, such as fl ower vases,
on top. Avoid from dripping or splashing. If any solid
object or liquid falls into the cabinet, unplug the TV
and have it checked by qualifi ed personnel before
operating it any further.
Cleaning
Before cleaning, unplug the TV set from the wall
outlet. Do not use liquid or aerosol cleaners. Use
soft and dry cloth.
Heat and Flames
The set should not be placed near to open flames and
sources of intense heat such as an electric heater.
Ensure that no open fl ame sources, such as lighted
candles, are placed on top of the TV. Batteries should
not be exposed to excessive heat such as sunshine,
fi re or the like.
Caring for the cabinet
• Use a soft cloth (cotton, flannel, etc.) and gently wipe
the surface of the cabinet.
• Using a chemical cloth (wet/dry sheet type cloth,
etc.) may deform the components of the main unit
cabinet or cause cracking.
• Wiping with a hard cloth or using strong force may
scratch the surface of the cabinet.
• If the cabinet is very dirty, wipe with a soft cloth
(cotton, flannel, etc.) soaked in neutral detergent
diluted with water and thoroughly wrung out, and
then wipe with a soft dry cloth.
• Avoid using benzene, thinner, and other solvents,
as these may deform the cabinet and cause the
paint to peel off.
• Do not apply insecticides or other volatile liquids.
Also, do not allow the cabinet to remain in contact
with rubber or vinyl products for a long period of
time. Plasticizers inside the plastic may cause the
cabinet to deform and cause the paint to peel off.
Caring for the front panel
• Turn off the main power and unplug the AC cord
from the wall outlet before handling.
• Gently wipe the surface of the front panel with a
soft cloth (cotton, flannel, etc.). To protect the front
panel, do not use a dirty cloth, liquid cleaners, or a
chemical cloth (wet/dry sheet type cloth, etc.). This
may damage the surface of the front panel.
• Wiping with a hard cloth or using strong force may
scratch the surface of the front panel.
• Use a soft damp cloth to gently wipe the front panel
when it is really dirty (It may scratch the surface of
the front panel when wiped strongly).
• If the front panel is dusty, use an anti-static brush,
which is commercially available, to clean it.
Lightning
In case of storm and lightning or when going on
holiday, disconnect the power cord from the wall outlet.
Replacement Parts
When replacement parts are required, make sure that
the service technician has used replacement parts,
which are specified by the manufacturer or have the
same specifications as the original one. Unauthorized
substitutions may result in fire, electrical shock or
other hazards.
Servicing
Please refer all servicing to qualified personnel. Do
not remove the cover yourself as this may result in
an electric shock.
Waste Disposal
• Packaging and packaging aids are recyclable and
should principally be recycled. Packaging materials,
such as a foil bag should be kept away from children
• Batteries, including those which are heavy metal
free, should not be disposed of with household
waste. Please dispose of used batteries in an
environmentally friendly manner. Find out about the
legal regulations which apply in your area.
English - 5 -
• Do not try to recharge batteries, there is a danger
of explosion. Replace batteries only with the same
or equivalent type.
• Batteries should not be exposed to excessive heat
such as sunshine, fire or the like.
This symbol on the product or on its
packaging means that your electrical
and electronic device should be disposed
at the end of its service life separately
from your household wastes. There are
separate collection systems for recycling
in the EU. For more information, please
contact the local authority or the dealer
where you purchased the product.
Disconnecting the Device
The mains plug is used to disconnect the TV set
from the mains and therefore it must remain readily
operable.
Headphone Volume
Excessive sound pressure from earphones and
headphones can cause hearing loss.
Installation
To prevent injury, this device must be securely
attached to the wall in accordance with the installation
instructions when mounted to the wall (if the option
is available).
LCD Screen
The LCD panel is a very high technology product with
about a million thin fi lm transistors, giving you fine
picture details. Occasionally, a few non-active pixels
may appear on the screen as a fi xed blue, green or
red point. Please note that this does not affect the
performance of your product.
Warning
Do not leave your TV in standby or operating mode
when you leave your house.
Connection to a Television Distribution
System (Cable TV etc.) from Tuner
Device connected to the protective earthing of the
building installation through the mains connection or
through other apparatus with a connection to protective
earthing-and to a television distribution system using
coaxial cable, may in some circumstances create a
fire hazard.
Connection to a cable distribution system has
Connection to a cable distribution system has
therefore to be provided through a device providing
electrical isolation below a certain frequency range
(galvanic isolator, see EN 60728-11).
Note:The HDMI connection between PC and TV may cause
radio interference in which case it is recommended to use
VGA(DSUB-15) connection.
The Standby Off/On button doesn´t separate this
device completely from mains. Moreover the device
consumes power in the standby operation. In order to
separate the device completely from mains, the mains
plug has to be pulled from the mains socket. Because
of that the device should be set up in a way, that an
unobstructed access to mains socket is guaranteed,
so that in case of emergency the mains plug can be
pulled immediately. To exclude the danger of fire, the
power cord should principally be separated from the
mains socket prior to a longer period of non-usage,
i.e. during vacations.
Electrical device not in the hands of
children
Never let children use any electrical device
unsupervised. Children cannot always recognise
possible dangers. Batteries / accumulators can be
life threatening when swallowed. Store batteries out
of the reach of small children. In case of swallowing
a battery medical aid has to be sought immediately.
Also keep the packaging foils away from children as
there is danger of suffocation.
English - 6 -
Environmental Information
This television is designed to consume less energy
to help save the environment. To reduce energy
consumption, you should take the following steps:
You can use
You can use
Power Save Mode setting, located
in the
Picture menu. If you set Power Save Mode
as
Eco, the TV will switch to energy-saving mode
and luminance level of TV set will be decreased to
optimum level. Note that some picture settings will be
unavailable to be changed when the TV is in
Power
Save Mode.
When you press the right button on the remote while
When you press the right button on the remote while
Power Save Mode is set to “Eco”, “Screen will be
off in 15 seconds.” message will be displayed on
the screen. If the
Power Save Mode option is set to
“
Disabled” press the left button. Select PROCEED
and press
OK to continue. The screen will turn off
immediately. If you do not press any buttons the
screen will turn off after 15 seconds.
If you disable
If you disable
Power Save Mode, the picture mode
will be automatically set to
Dynamic except the Mode
is set to
Game or Sports.
When the TV is not in use, please switch off or
disconnect the TV from the mains plug. This will also
reduce energy consumption.
Disconnect power when going away for longer time.
It is highly recommended to activate
Disconnect power when going away for longer time.
It is highly recommended to activate
Power Save Mode
setting to reduce your annual power consumption. And
also it is recommended to disconnect the TV from the
mains plug to save energy more when you do not use.
Please help us to save environment by following
Please help us to save environment by following
these steps.
Package Contents
TV
Remote Control
LCD TV
Batteries: 2 X AAA
Quick Guide
1 X Video & Audio Connection
Cable
Note: You should check the accessories after purchasing.
Make sure that each accessory is included.
As the manufacturer’s specification supports
communication on cable lengths shall be smaller
than 3m.
TV Control button & Operation
1. Up direction
2. Down direction
3. Volume / Info / Sources List selection and
2. Down direction
3. Volume / Info / Sources List selection and
Standby-On switch
The Control button allows you to control the Volume
/ Programme / Source and Standby-On functions of
the TV.
, switch is used for turning the TV on or off.
The position of the power switch may differ depending
on the model.
English - 7 -
Connect Power
IMPORTANT: The TV set is designed to operate on
220-240V AC, 50 Hz socket. After unpacking, allow
the TV set to reach the ambient room temperature
before you connect the set to the mains. Plug the
power cable to the mains socket outlet.
Antenna/Cable/Satellite Connection
Connect the aerial or cable TV plug to the AERIAL
INPUT (ANT.) or satellite lead to the SATELLITE
INPUT(LNB) located on the rear side of the TV.
“Satellite is only available in 362/363 series”.
Rear side of the TV:
Rear side of the TV:
SATELLITE
AERIAL
CABLE
Note: Satellite support is depending on the model.
(only available in LC-32LE363EN / LC-32LE362EN
(only available in LC-32LE363EN / LC-32LE362EN
/ LC-40LE363EN / LC-40LE362EN series)
Installing The Batteries Into The
Remote
• Remove the back cover to reveal the battery
compartment.
• Insert two size AAA batteries. Note the correct
polarity(+ or -). Do not mix old and new batteries.
Replace only with same or equivalent type.
• Place the cover back on.
Angle of the remote control unit
Use the remote control unit by pointing it towards the
remote control sensor.
Objects between the remote control unit and sensor
Objects between the remote control unit and sensor
may prevent proper operation.
Cautions regarding the remote control unit
• Do not expose the remote control unit to shock.
In addition, do not expose the remote control unit
to liquids, and do not place in an area with high
humidity.
• Do not install or place the remote control unit under
direct sunlight. The heat may cause deformation
of the unit.
• The remote control unit may not work properly if
the remote control sensor of the TV is under direct
sunlight or strong lighting. In such cases, change the
angle of the lighting or the TV, or operate the remote
control unit closer to the remote control sensor.
Switching On/Off
To Switch the TV On
Connect the power cord to the mains socket. Switch
the “
” button on the TV to position “|” so the TV
will switch to standby mode. Then the standby LED
lights up.
To switch on the TV from standby mode either:
• Press the “ ” button,
To switch on the TV from standby mode either:
• Press the “ ” button,
P+ / P- or a numeric button
on the remote control.
• Press the side function switch on the TV until the TV
comes on from standby.
The TV will then switch on.
To Switch the TV to Standby
To switch the TV to low power standby press the
“ ” button on the remote control or press the side
“ ” button on the remote control or press the side
function switch on the TV until the TV switches into
standby mode.
To Switch the TV Off
Switch the “
” button on bottom of the TV to
position 2 as illustrated - “
”, to isolate the TV from
the mains, the LED will go out.
Click on the first or last page to see other LC-40LE361E (serv.man2) service manuals if exist.