Sharp LC-32SH330E Service Manual ▷ View online
2008-03-14
LC-26SH330, LC-32SH330, LC-42SH330
9
Appendix
Troubleshooting
problem
possible Solution
No picture
1.
Connect power cord correctly.
2.
Turn on power.
3.
Connect signal cable correctly.
4.
Press any button on the LCD TV.
Abnormal colours
Connect signal cable correctly.
Twisted picture
1.
Connect signal cable correctly.
2. Please use compatible signal.
Picture too dark
Adjust brightness and contrast.
Audio only, no images
1.
Please check if input signal is connected correctly.
2. TV-RF signal must not be lower than 50dB.
Picture only, no audio
1.
Connect signal cable correctly.
2.
Adjust volume to proper level.
3.
Connect audio signal cable correctly.
4.
TV-RF signal must not be lower than 50dB.
Cannot use remote control
1.
Please change battery.
2.
Turn off power for 10 seconds; and then restart power.
Cannot receive sufficient channels
through antenna
through antenna
Please use the Channel scan function to increase the number of channels not included in memory.
No colour
Please adjust the colour setup
Blinking picture accompanied by ghost
image
image
1.
Check the connection of antenna/signal cable.
2.
Check if channel is in play mode.
3.
Press signal source and change input mode.
Broken lines or segments
Adjust antenna.
Keep the TV away from noise sources, such as automobiles, neon lights, and hair dryers.
Keep the TV away from noise sources, such as automobiles, neon lights, and hair dryers.
Certain TV channels are blocked (Hope to
acquire some channels)
acquire some channels)
Please use the Update scan method to add the channels not included in memory
Overlapping images or ghost images
Please use multi-directional outdoor antenna. (If your TV is subject to the influence of nearby mountains or
buildings).
buildings).
Cannot use a function
If the item you choose turns gray, that item cannot be selected.
Cannot receive programs
Please use the Update scan method to add the channels not included in memory.
1. When a lamp in LCD panel is broken and the
protector circuit in inverter operates and we
tune on the this set, LED keep red? or Green?
2. Service man only change the lamp in LCD
panel?
protector circuit in inverter operates and we
tune on the this set, LED keep red? or Green?
2. Service man only change the lamp in LCD
panel?
1. If the lamp(s) is(are) broken, panel inverter will not kick on the lamps, so TV set phenomena will be "no picture
on display."
But the TV system is still working, that is the RC can also control LED.
When AC power on, the LED will keep last status and when use RC DC power on, the LED will keep green light.
2. The failed panel should be sent back to Panel maker (CMO) via RMA process.
Panel maker (CMO) will not rework the lamps at customer's side since the repaired panel should be checked
through regular inspection flow to secure the quality.
on display."
But the TV system is still working, that is the RC can also control LED.
When AC power on, the LED will keep last status and when use RC DC power on, the LED will keep green light.
2. The failed panel should be sent back to Panel maker (CMO) via RMA process.
Panel maker (CMO) will not rework the lamps at customer's side since the repaired panel should be checked
through regular inspection flow to secure the quality.
Cautions regarding use in high and low temperature environments
• When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed. This
• When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed. This
is not a malfunction, and the unit will recover when the temperature returns to normal.
• Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near a
heater, as this may cause the cabinet to deform and the LCD panel to malfunction.
• Storage temperature: +5°C to +35°C.
Information on the software license for this product
Software composition
The software included in this product is comprised of various software components whose individual copyrights are held by SHARP or by third
parties.
parties.
Software developed by SHARP and open source software
The copyrights for the software components and various relevant documents included with this product that were developed or written by
SHARP are owned by SHARP and are protected by the Copyright Act, international treaties, and other relevant laws. This product also makes
use of freely distributed software and software components whose copyrights are held by third parties. These include software components
covered by a GNU General Public License (hereafter GPL), a GNU Lesser General Public License (hereafter LGPL) or other license Agreement.
SHARP are owned by SHARP and are protected by the Copyright Act, international treaties, and other relevant laws. This product also makes
use of freely distributed software and software components whose copyrights are held by third parties. These include software components
covered by a GNU General Public License (hereafter GPL), a GNU Lesser General Public License (hereafter LGPL) or other license Agreement.
Acknowledgements
The following open source software components are included in this product:
•linuxkernel•modutils•glibc•zlib•libpng
•linuxkernel•modutils•glibc•zlib•libpng
LC-26SH330, LC-32SH330, LC-42SH330
10
[3] DIMENSIONS
2008-03-14
LC-26SH330, LC-32SH330, LC-42SH330
11
CHAPTER 2.
REMOVING OF MAJOR PARTS
[1] REMOVING OF MAJOR PARTS(LC-26SH330)
1. Assy/Panel Removal
Notes: Please put your machine on soft material to avoid to scrape panel when you disassemble it.
Front view
Fig.1
Back view
Fig.2
Step 1. Remove the Base Assy.
1. Remove the base as Fig.3.
Remove the 4 screws as Fig.3 and pull out the base as Fig.4
Fig.3
LC-26SH330, LC-32SH330, LC-42SH330
12
Fig.4
2. Remove the 4 screws. Detach the Neck as Fig.4.
Step 2. Remove the REAR COVER Assy.
1. Remove the 12 screws. Detach the
REAR COVER
as Fig.5.
Fig.5
Step 3. Remove the Main, Power board and the Speakers.
Fig.6
1. Disconnect 4 cables and remove the 4 screws. Detach the Main board as Fig.7.
Click on the first or last page to see other LC-32SH330E service manuals if exist.