DOWNLOAD Sharp LC-32GA3E (serv.man26) Service Manual ↓ Size: 1.77 MB | Pages: 32 in PDF or view online for FREE

You can detach the system speaker when using external speaker.
Before removing (or attaching) speaker, unplug the AC cord from the AC outlet.

• Do not remove the stand and speaker from the TV unless using an optional bracket to mount it.
• When using the TV with the supplied stand attached, do not remove the speaker. Doing so may disturb

• Before performing work make sure to turn off the TV.
• Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being

damaged.

• The speaker terminals on the TV are only for the attached speaker. Do not connect any third party plug or speaker to the

terminal.

• Insert the speaker plug completely into the terminal.

• To attach the speaker and stand, perform the above steps in reverse order.

• Installing the LCD Colour TV requires special skill that should only be performed by qualified service personnel.

• You can ask a qualified service personnel about using an optional AN-37AG2 bracket to mount the TV to the

wall.

1 Unfasten the screws used to

secure the speaker bracket
covers, and then detach them.

2 Take off the speaker terminal

cover.

Unfasten the screws used to
secure the stand in place, and then
detach the stand from the Display.
(Hold the stand so it will not drop
the stand from the edge of the base
area.)

Disconnect the cable from the
speaker.

Now the speaker can be removed
from the Display.

Unfasten the screw used to
secure the speaker bracket.

• Perform the steps 2 to 4 on the

both sides of the speaker to
remove it.

LC-32GA3E(E)-a

04.6.3, 8:04 AM

7

Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause

chemical leakage in old batteries.

• Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you

find any chemical leakage, wipe thoroughly with a cloth.

• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove the batteries from it.

Before using the TV for the first time, insert two “AAA” size batteries (supplied).  When the batteries become
depleted and the remote control fails to operate, replace the batteries with new “AAA” size batteries.

Use the remote control unit by pointing it towards the remote sensor window.
Objects between the remote control unit and sensor window may prevent proper
operation.

• Do not expose the remote control unit to shock.

In addition, do not expose the remote control unit to liquids, and do not place
in an area with high humidity.

• Do not install or place the remote control unit under direct sunlight.

The heat may cause deformation of the unit.

• The remote control unit may not work properly if the remote sensor window of

the Display is under direct sunlight or strong lighting. In such case, change
the angle of the lighting or Display, or operate the remote control unit closer to
the remote sensor window.

30

°

30

°

Remote

control sensor

7 m

23 feet

Press and slide the battery cover to open it.

Insert two supplied “AAA” size batteries.

• Place batteries with their terminals corresponding to

the (e) and (f) indications in the battery
compartment.

Close the battery cover.

LC-32GA3E(E)-b

04.6.3, 8:04 AM

8

Simple operations for watching a TV programme

To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of connecting to an
antenna with a coaxial cable.

If your outdoor antenna uses a 75-ohm coaxial cable with a standard DIN45325
plug (IEC 169-2), plug it into the IN terminal at the rear of the TV.

LC-32GA3E(E)-b

04.6.3, 8:04 AM

9

01 SAT.1

02 PR07

03 KABEL

01 SAT.1

02 PR07

03 KABEL

01 55.25

02 85.25

03 102.25

When the TV powers on for the first time after purchase
(see page 14), the initial auto installation is invoked.
You can automatically set language, country and
channels in successive operations.

1 Press a/b/c/d to select your country

or area listed on the screen.

2 Press OK to enter the setting.

• The programme auto search starts at the same

time.

1 Press  a/b/c/d to select the desired

language listed on the screen.

2 Press OK to enter the setting.

After this setting, auto search starts with the following
order.

1 Programme auto search
2 Auto labelling
3 Auto sorting
4 Preset download

You do not need to do anything during the auto search.

• The illustrations and on-screen displays in this manual

are for explanation purposes and may vary slightly from
the actual operations.

After finding TV channels, the TV starts naming each
TV channel found.

• The TV can only name channels where the channel

labelling information is provided. If no channel labelling
information is provided, the TV only displays the channel
number, leaving the channel name blank.

Channel auto search finds all channels viewable in
your area.

• If no channel is found, “No programme found.” displays.

And the auto installation finishes.

When auto sorting finishes, the TV automatically
downloads and stores each sorted channel from VCR.

• When a VCR is connected via INPUT 2, the TV sends all

preset channel information to the VCR. (See page 32.)

• “Auto Installation completed.” displays. After that, the

screen changes to the auto installation menu.

When channel auto labelling finishes, the TV starts
sorting the labelled channels.

The setup menu disappears and you can watch the
programme on channel 1.

• The initial auto installation functions only once. If the initial

auto installation is not completed, (ex: When menu screen
disappeared by not operating for a few minutes, when
the power shut down, etc.), try Auto Installation from the
set up menu. (See page 20.)

• The initial auto installation stops by pressing RETURN.

Austria
Belgium
Denmark
Finland
France
Germany
Greece
Ireland
Italy
Luxembourg
Netherlands
Norway

Poland
Portugal
Russia
Spain
Sweden
Switzerland
Turkey
United Kingdom
West Europe
East Europe

Dutch
English
Finnish
French
German
Greek
Italian

Polish
Portuguese
Russian
Spanish
Swedish
Turkish

LC-32GA3E(E)-b

04.6.3, 8:04 AM

10