DOWNLOAD Sharp LC-30HV2E (serv.man24) Service Manual ↓ Size: 10.91 MB | Pages: 71 in PDF or view online for FREE

RGB cable
(commercially available)

ø 3.5 mm stereo minijack cable
(commercially available)

INPUT SOURCE

TV

INPUT1

INPUT2

INPUT3

INPUT4

PC

1

R

6

GND (Ground)

q

Not connected

2

G

7

GND (Ground)

w

SDA

3

B

8

GND (Ground)

e

HD

4

Not connected

9

+5V

r

VD

5

CSYNC

0

GND (Ground)

t

SCL

Use the PC terminals to connect a computer.

A

• The PC input terminals are DDC1/2B-compatible.
• Refer to page 63 for a list of computer signals compatible with the System.

A
• Macintosh adaptor may be required for use for some Macintosh computers.

When connecting to a computer, the correct input
signal type is automatically detected. (See page 49.)
If the computer image does not come in clearly, you
may need to set the Auto Sync. adjustment on the “Auto
Sync.” in the menu. (See page 48.)

You only need to select the input source on the “INPUT
SOURCE” menu.

To view an image from a computer, select “PC” from
the “INPUT SOURCE” menu using b on the remote
control unit or INPUT on the Display. (See page 49.)

A

• Each time b is pressed, the input source toggles.

You can detach the system speakers when using external amplifier/speakers.

• Before performing work make sure to turn off the System.
• Before performing work spread cushioning over a flat surface to lay the Display on. This will prevent it from

being damaged.

L

• The speaker terminals on the Display is only for the attached speakers. Do not connect any third party plug or speaker to

the terminal.

• Insert the speaker plug completely into the terminal.
• Do not handle or move the display by the speakers.

A

• Perform the same steps for both left and right speakers.
• To attach the speakers, perform the above steps in reverse order.

Unfasten the screws used to
secure the speakers in place.

Take hold of the speaker and
slowly slide it sideways.
(The speaker plug is still
inserted, so make sure not to
pull the speaker too far.)

Remove the speaker plug from
the terminal on the Display.
(Do not remove the plug by
pulling the cord.)
Now the speaker can be
detached from the display.

Speaker
plug

Option

MENU

Position

H-Pos.

V-Pos.

Reset

RETURN

[0]

[0]

–15

–30

+15

+30

/

/

/

Centres the image by moving it to the left or
right.

Centres the image by moving it up or down.

For adjusting a picture’s horizontal and vertical
position.

Press MENU.

Press  a/b to select “Option”, and then press
ENTER.

Press  a/b to select “Position”, and then press
ENTER.

Press a/b to select “H-Pos.” or “V-Pos.”.

Press  c/d to adjust the item to your desired
position.

Press MENU to exit the menu.

A
• For resetting all adjustment items set to the factory preset

values,
1 Press a/b to select “Reset”, and then press ENTER.
2 Press a/b to select “Yes”, and then press ENTER.

• Return to the previous menu by pressing RETURN.
• Adjustments are stored separately according to input

• You can easily move the image position as shown on page

47, but when the power is switched off the image will return
to the previously memorised position.

You can move the picture around on the screen.

/

/

/

Press a/b/c/d to move an image on the screen to
the desired position. Press ENTER to return to the initial
image position.

A
• While pressing a/b/c/d, an on-screen image,

“Adjusting Position” displays to the desired position.

• This setting cannot be stored. Once the System shuts

down or enters standby mode, the setting is erased. To
move the picture around the screen again, you must
perform the above procedure again.

• The image position setting using the steps on page 46

can be stored. Select either according to your objectives.

• “TV”, “INPUT1”, “INPUT2”, “INPUT3”, “INPUT4” and “PC”

modes can each adjust the image position setting on this
page. The same for WIDE modes.

• An on-screen image from a PC source cannot be moved

around.

• Even when the image fills the screen, its position can be

adjusted with this function.