Sharp XG-V10WE (serv.man8) Service Manual ▷ View online
13
XG-V10WE
AN-SD1E/S422E
Dimensions
414.5
221.85
74.5
25.65
81.85
621.3
444.2
3.9
42
376
Rear View
Top View
Side View
Side View
Front View
Bottom View
Units: mm
14
XG-V10WE
AN-SD1E/S422E
REMOVING OF MAJOR PARTS
1. Removing the intake cover, intake filter and lamp unit.
1-1. Detach the intake cover.
1-2. Detach the intake filter.
1-3. Loosen the lock screw from the lamp cover and slide the lamp cover off position.
1-4. Remove the three lock screws each from the lamp units 1 and 2, and detach these units.
1-2. Detach the intake filter.
1-3. Loosen the lock screw from the lamp cover and slide the lamp cover off position.
1-4. Remove the three lock screws each from the lamp units 1 and 2, and detach these units.
1-1
1-2
1-3
1-4
1-4
Intake cover
Intake filter
Lamp unit 2
Lamp cover
Lamp unit 1
15
XG-V10WE
AN-SD1E/S422E
2. Removing the front, top and rear panels.
2-1. Remove the ten lock screws from the rear panel. Disconnect the connector (RD) of the remote control receiver
PWB unit 2. Then detach the rear panel.
2-2. Remove the two lock screws from the remote control receiver PWB unit 2. Detach the remote control receiver
PWB unit 2.
2-3. Remove the two lock screws from the lens cover (top) and detach the lens cover (top).
2-4. Remove the four lock screws from the lens cover (bottom) and detach the lens cover (bottom).
2-5. Remove the four lock screws from the shutter holder and detach the shutter holder.
2-6. Take out the shutter.
2-7. Remove the seven lock screws from the front panel.(Long size 2, Short size 5)
2-8. Remove the four lock screws from the top panel.
2-9. Slowly lift the back of the top panel. Disconnect the following connectors: connector (KY) of the operation
2-4. Remove the four lock screws from the lens cover (bottom) and detach the lens cover (bottom).
2-5. Remove the four lock screws from the shutter holder and detach the shutter holder.
2-6. Take out the shutter.
2-7. Remove the seven lock screws from the front panel.(Long size 2, Short size 5)
2-8. Remove the four lock screws from the top panel.
2-9. Slowly lift the back of the top panel. Disconnect the following connectors: connector (KY) of the operation
unit, connector (L) of the leaf switch, and connector (RE) of the LED PWB unit and remote control receiver
PWB unit 1. Lift and detach both the front and top panels.
PWB unit 1. Lift and detach both the front and top panels.
2-10. Remove the two lock screws from the LED PWB unit. Detach the LED PWB unit.
2-11. Open the hooks of the remote control receiver PWB unit 1 and take out the remote control receiver PWB 1.
2-11. Open the hooks of the remote control receiver PWB unit 1 and take out the remote control receiver PWB 1.
2-7
2-7
2-8
2-11
2-10
2-8
2-9
2-7
2-3
2-5
2-4
2-5
2-6
2-1
2-2
(RE)
(KY)
(L)
(RD)
LED PWB unit
Top panel
Rear panel
Remote control receiver PWB unit 2
Remote control
receiver PWB unit 1
receiver PWB unit 1
Front panel
Shutter
Shutter holder
Lens cover (top)
Lens cover (bottom)
16
XG-V10WE
AN-SD1E/S422E
3. Removing the reinforcing angles and intake fan duct assembly.
3-1. Remove the four lock screws from the front reinforcing angle and detach this angle.
3-2. Remove the four lock screws from the rear reinforcing angle and detach this angle.
3-3. Remove the five lock screws from the intake fan duct assembly and detach this assembly.
3-4. Remove the two lock screws from the intake cover and detach this cover.
3-2. Remove the four lock screws from the rear reinforcing angle and detach this angle.
3-3. Remove the five lock screws from the intake fan duct assembly and detach this assembly.
3-4. Remove the two lock screws from the intake cover and detach this cover.
3-2
3-1
3-1
3-2
3-2
3-4
3-3
3-3
3-3
Front reinforcing angle
Rear reinforcing angle
Intake cover
Intake fan duct assembly
Click on the first or last page to see other XG-V10WE (serv.man8) service manuals if exist.