Sharp XG-PH50X (serv.man18) User Manual / Operation Manual ▷ View online
Introduction
17
Using the Remote Control
Inserting the Batteries
The batteries (two R-6 batteries (“AA” size,
UM/SUM-3, HP-7 or similar)) are supplied in
the package.
UM/SUM-3, HP-7 or similar)) are supplied in
the package.
1
Press the tab and lift open the battery
cover in the direction of the arrow.
cover in the direction of the arrow.
2
Insert the batteries.
• Insert the batteries making sure the po-
larities correctly match the
and
marks inside the battery compartment.
3
Insert the tabs on the end of the
battery cover into their slots and
press the cover into position.
battery cover into their slots and
press the cover into position.
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.
Caution
• Insert the batteries making sure the polarities correctly match the and marks inside the battery compartment.
• Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
• Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak.
Battery fluid from leaked batteries is harmful to skin, therefore ensure to first wipe them and then remove them
using a cloth.
using a cloth.
• The batteries included with this projector may run down in a short period, depending on how they are kept.
Ensure to replace them as soon as possible with new batteries.
• Remove the batteries from the remote control if you will not be using the remote control for a long time.
Usable Range
The remote control can be used to control
the projector within the ranges shown in the
illustration.
the projector within the ranges shown in the
illustration.
Note
• The signal from the remote control can be re-
flected off a screen for easy operation. How-
ever, the effective distance of the signal may
differ depending on the screen material.
ever, the effective distance of the signal may
differ depending on the screen material.
When using the remote control:
• Ensure not to drop, expose to moisture or high
temperature.
• The remote control may malfunction under a
fluorescent lamp. In this case, move the pro-
jector away from the fluorescent lamp.
jector away from the fluorescent lamp.
Front View
Rear View
Remote control
signal transmitters
signal transmitters
Remote control sensor
Remote control
30
°
30
°
30
°
23' (7 m)
Remote control sensor
Remote control
signal transmitters
signal transmitters
Remote control
30
°
30
°
30
°
23' (7 m)
XG-PH50X_Print_E_P07_21.p65
04.11.18, 9:51
17
18
Using the Remote Control
Using the Remote Control with a Signal Cable
When the signals from the remote control cannot be reached due to the range or positioning of the projec-
tor, you can connect the remote control to the projector with a ø3.5 mm minijack cable (commercially avail-
able or available as Sharp service part QCNWGA038WJPZ).
tor, you can connect the remote control to the projector with a ø3.5 mm minijack cable (commercially avail-
able or available as Sharp service part QCNWGA038WJPZ).
Switching the Remote Control Mode
The remote control has two functions. One is projector control and the other is wireless computer mouse.
Slide the ADJ./MOUSE switch on the remote control to other side compatible to the desired usage.
Slide the ADJ./MOUSE switch on the remote control to other side compatible to the desired usage.
Info
• When using the remote control as the wireless computer mouse, connect the supplied remote mouse
receiver to the computer. (See page 19.)
Side view
Remote control
To WIRED R/C JACK
To WIRED REMOTE terminal
ø3.5 mm minijack cable (commercially available or
available as Sharp service part QCNWGA038WJPZ)
available as Sharp service part QCNWGA038WJPZ)
ADJ.
MOUSE
ADJ.
MOUSE
Projector control
Wireless computer mouse
XG-PH50X_Print_E_P07_21.p65
04.11.18, 9:51
18
Introduction
19
Using the Remote Control as the Wireless Computer Mouse
When connecting the supplied remote
mouse receiver to the computer, you can use
the remote control as the wireless computer
mouse.
mouse receiver to the computer, you can use
the remote control as the wireless computer
mouse.
1
Connect the supplied remote
mouse receiver to the USB termi-
nal on the computer.
mouse receiver to the USB termi-
nal on the computer.
2
Slide the ADJ./MOUSE
switch on the remote con-
trol to the MOUSE position.
switch on the remote con-
trol to the MOUSE position.
3
Use the mouse function.
• Point the remote control at the remote
mouse receiver.
■ When moving the cursor
Press '/"/\/|.
■ When left-clicking
Press
.
■ When right-clicking
Press
.
■ When your computer supports only a
one-click mouse (such as Macintosh
®
)
Press
or
. (
and
have com-
mon function.)
ADJ.
MOUSE
Remote mouse
receiver
receiver
Supplied
accessory
Note
• This function only works with the Microsoft
®
Windows
®
OS and Mac OS
®
. However, this
function does not work with the following op-
eration systems that do not support USB.
eration systems that do not support USB.
•
Versions earlier than Windows
®
95.
•
Versions earlier than Windows
®
NT4.0.
•
Versions earlier than Mac OS
®
8.5.
• Confirm that the computer recognizes the USB
connection.
• While the remote control is connected to the
projector, you cannot use the wireless computer
mouse function.
mouse function.
Computer
To USB terminal
Remote mouse receiver
Mouse/adjustment button ('/"/\/|)
ADJ./MOUSE switch
R-click button
L-click button
XG-PH50X_Print_E_P07_21.p65
04.11.18, 9:51
19
20
Quick Start
Page 22
1.
Place the projector facing a screen
Pages 27, 37
Page 37
Press
on the projector or
on the remote control.
This section shows the basic operation (projector connecting with the computer). For details, see the page
described below for each step.
Setup and Projection
In this section, connection of the projector and the computer is explained using one example.
2.
Connect the projector to the computer and plug the power
cord into the AC socket of the projector
cord into the AC socket of the projector
3.
Remove the lens cap and turn the projector on
When connecting equipment other than the computer,
see pages 30 and 36.
see pages 30 and 36.
5
4 6
6
7
6
3
4
8
8
3
4
6
7
4 6
8
5
XG-PH50X_Print_E_P07_21.p65
04.11.18, 9:51
20
Click on the first or last page to see other XG-PH50X (serv.man18) service manuals if exist.