Sharp XG-PH50X (serv.man18) User Manual / Operation Manual ▷ View online
Quick Start
21
Pages 38, 39
4.
Adjust the angle
5.
Adjust the focus and the zoom
Page 40
8.
Turn the power off
Page 37
7.
Select the input mode
Page 45
1
1
1
1
1 Press
on the projector or
on the remote control to adjust the focus.
2
2
2
2
2 Press
on the projector or
on the remote control to adjust the zoom.
Press
on the projector or
on the remote control to select the “INPUT1” mode.
••••• When pressing
on the projector, input mode switches in order of :
INPUT 1
INPUT 2
INPUT 3
.
Pressing
on the projector switches between “INPUT4” and “INPUT5”.
••••• When using the remote control, press
/
/
/
/
to switch the input mode.
Press
on the projector or
on the remote control. While the confirmation message is displayed,
press
or
again.
••••• Disconnect the power cord from the AC outlet after the cooling fan stops.
Adjust the projector angle
••••• Shift the lens horizontally and vertically.
••••• Shift the lens horizontally and vertically.
1
1
1
1
1 Press
on the projector or
on the
remote control.
2
2
2
2
2 Press ', ", \ or | on the projector or the
remote control.
••••• Adjust the projector angle by rotating the adjust-
ment feet.
6.
Correcting the image distortion due to the projection angle
1
1
1
1
1 Press
on the projector or
on the
remote control.
2
2
2
2
2 Press
on the projector or
on the
remote control.
3
3
3
3
3 Press ', ", \ or | to move the position for
the upper left of the image.
Page 41
4
4
4
4
4 Press
or
to set the position.
5
5
5
5
5 Repeat the same procedure with the positions
for the upper right, lower right and lower left
of the image.
••••• When the position of the lower left is set, the
of the image.
••••• When the position of the lower left is set, the
correction is made and the display disappears.
"
"
"
"
" On-screen Display (RGB)
"
"
"
"
" On-screen Display
XG-PH50X_Print_E_P07_21.p65
04.11.18, 9:51
21
22
Setting Up the Projector
Position the projector perpendicular to the screen with the projector’s feet flat and level to achieve an
optimal image.
optimal image.
Note
• The projector lens should be centered in the middle of the screen. If the horizontal line passing through
the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.
• For an optimal image, position the screen so that it is not in direct sunlight or room light. Light falling
directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights
when setting up the projector in a sunny or bright room.
when setting up the projector in a sunny or bright room.
Standard Setup (Front Projection)
■ Place the projector at the required distance from the screen according to the desired picture size. (For
details, refer to “SETUP GUIDE” contained on the supplied CD-ROM.)
Setting Up the Projector
Indication of the Projection Image Size and Projection Distance
For details, refer to “SETUP GUIDE” contained on the supplied CD-ROM.
Example : NORMAL Mode (4:3) for the standard zoom lens (AN-PH30EZ)
Example : NORMAL Mode (4:3) for the standard zoom lens (AN-PH30EZ)
300"
200"
100"
84"
60"
60"
Picture Size
240"×180"
160"
×
120"
80"
×
60"
67"
×
50"
48"
×
36"
Projection Distance
36'
–44'
(11.0 m – 13.4 m)
24'
–29'4
"
(7.3 m
– 8.9 m)
12'
–14'8
"
(3.7 m
– 4.5 m)
10'1
"–12'4
"
(3.1 m
– 3.8 m)
7'2
"–8'10
"
(2.2 m – 2.7 m)
XG-PH50X_Print_E_P22_23.p65
04.11.17, 19:22
22
Setup
23
Projecting a Reversed Image
Projection from behind the Screen
■ Place a translucent screen between the projector and the audience.
■ Reverse the image by setting “Rear” in the “PRJ Mode” menu. (See page 84.)
Projection Using a Mirror
■ Place a mirror (normal flat type) in front of the lens.
■ When the translucent screen is placed between the mirror and audience, set to “Front” in the “PRJ Mode”
menu. (See page 84.)
■ When the mirror is placed on the audience side, set to “Rear” in the “PRJ Mode” menu. (See page 84.)
Info
• When using a mirror, ensure that both the projector and the mirror are carefully placed so the projected
light does not shine into the eyes of the audience.
Ceiling-mount Setup
■ It is recommended that you use the optional Sharp ceiling-mount
bracket for this installation.
Before mounting the projector, contact your nearest Sharp Au-
thorized Projector Dealer or Service Center to obtain the recom-
mended ceiling-mount bracket (sold separately).
• AN-PHCM20 ceiling-mount bracket, its AN-EP101AP extension
Before mounting the projector, contact your nearest Sharp Au-
thorized Projector Dealer or Service Center to obtain the recom-
mended ceiling-mount bracket (sold separately).
• AN-PHCM20 ceiling-mount bracket, its AN-EP101AP extension
tube (for U.S.A.).
• AN-NV6T ceiling-mount bracket, its AN-TK201 and AN-TK202
extension tubes (for countries other than the U.S.A.).
■ Invert the image by setting “Ceiling + Front” in “PRJ Mode”. See
page 84 for use of this function.
Translucent screen
Audience
Set to “Front”
Audience
Translucent screen
Mirror
Set to “Rear”
Audience
Mirror
XG-PH50X_Print_E_P22_23.p65
04.11.17, 19:22
23
24
INPUT/OUTPUT Terminals and Connectable Main Equipment
AUDIO input (2, 3) terminal
Connecting an audio cable. (Shared
audio input terminal for INPUT 2
and 3.) (See pages 28 and 29.)
audio input terminal for INPUT 2
and 3.) (See pages 28 and 29.)
AUDIO input (1) terminal
Connecting an audio cable.
(Audio input terminal
dedicated to INPUT 1.) (See
page
(Audio input terminal
dedicated to INPUT 1.) (See
page
27
.)
AUDIO input (4, 5) terminals
Connecting an audio cable.
(Shared audio input terminal for
INPUT 4 and 5.) (See page
(Shared audio input terminal for
INPUT 4 and 5.) (See page
34
.)
WIRED REMOTE terminal
For connecting the remote control when
the signals from the remote control cannot
reach the remote control sensor. (See
page 18.)
the signals from the remote control cannot
reach the remote control sensor. (See
page 18.)
AUDIO OUTPUT terminal
Connecting an audio cable.
(Shared audio output terminal for
INPUT 1 – 5.) (See page
(Shared audio output terminal for
INPUT 1 – 5.) (See page
36
.)
LAN terminal
(10 BASE-T/100 BASE-TX)
Connecting the computer or the
HUB using a LAN cable. (See page
HUB using a LAN cable. (See page
35
.)
INPUT 5 terminal
Connecting video equipment with S-video
output terminal (VCR, DVD player, etc.).
(See page
output terminal (VCR, DVD player, etc.).
(See page
34
.)
RS-232C terminal
Connecting the computer to
control the projector.
(See page
control the projector.
(See page
35
.)
INPUT 4 terminal
Connecting video equipment without
S-video output terminal. (See page
S-video output terminal. (See page
34
.)
OUTPUT (FOR INPUT 1, 2)
terminal
terminal
Connecting the monitor when you
want to simultaneously watch the
projection image on the monitor.
(See page
want to simultaneously watch the
projection image on the monitor.
(See page
36
.)
INPUT 1, 2 terminal
Connecting the computer. (See
pages
pages
27 and 28
.)
Connecting video equipment with
component output terminal (DVD
player, DTV decoder, DVD recorder
with hard disc, etc.). (See page
component output terminal (DVD
player, DTV decoder, DVD recorder
with hard disc, etc.). (See page
33
.)
INPUT 3 terminal
Connecting the computer. (See
page
page
29
.)
Connecting video equipment with
HDMI or DVI output terminal (DVD
player, DTV decoder, DVD recorder
with hard disc, etc.). (See pages
HDMI or DVI output terminal (DVD
player, DTV decoder, DVD recorder
with hard disc, etc.). (See pages
30
and 31
.)
Connections
XG-PH50X_Print_E_P24_36.p65
04.11.17, 19:23
24
Click on the first or last page to see other XG-PH50X (serv.man18) service manuals if exist.