Sony NW-E5 Service Manual ▷ View online
NW-E5
SERVICE MANUAL
NETWORK WALKMAN
SPECIFICATIONS
AEP Model
UK Model
Recording time
Approx. 90 min. (132kbps)
Approx. 120 min. (105kbps)
Approx. 180 min. (66kbps)
Approx. 120 min. (105kbps)
Approx. 180 min. (66kbps)
Sampling frequency response
44.1kHz
Recording format
ATRAC3
Frequency response
20 to 20,000 Hz (single signal measurement)
Output
Earphone: stereo mini-jack
Signal-to-noise ratio (S/N)
More than 80dB (excluding 66 kbps)
Dynamic range
More than 85dB (excluding 66 kbps)
Operating temperature
5˚C to 35˚C (-41˚F to 95˚F)
Power source
LR03 (Size AAA) alkaline battery
Battery life
Approx. 5 hours
Dimensions (approx.)
81 x 32 x 14.6 mm (3
1
/
4
x 1
1
/
4
x 4 x
19
/
32
inches)
(w/h/d, projecting parts not included)
Mass (approx.)
45g (1.6 oz) (battery included)
Memory capacity
96MB (including the system software: 92.6MB available)
Supplied accessories
LR03 (Size AAA) alkaline battery (1)
Earphones (1)
Headphones/earpones extension cord (1)
Dedicated USB cable (1)
Carrying pouch (1) (for other models)
CD-ROM (OpenMG Jukebox installation disc) (1)
NW-E3/E5 Operating Instructions (1)
OpenMG Jukebox Operating Instructions (1)
Earphones (1)
Headphones/earpones extension cord (1)
Dedicated USB cable (1)
Carrying pouch (1) (for other models)
CD-ROM (OpenMG Jukebox installation disc) (1)
NW-E3/E5 Operating Instructions (1)
OpenMG Jukebox Operating Instructions (1)
Design and specifications are subject to change without notice.
Ver 1.1 2003.06
9-873-036-12
2003F02-1
© 2003.06
Sony Corporation
Personal Audio Company
Published by Sony Engineering Corporation
2
NW-E5
Specifications ............................................................................ 1
1. SERVICING NOTE
....................................................... 2
2. GENERAL
....................................................................... 3
3. DISASSEMBLY
3-1. Chassis ASSY, Case ASSY ......................................... 7
3-2. LID, Case .................................................................... 7
3-3. Main Board, Power Board .......................................... 7
3-4. LCD Unit .................................................................... 8
3-5. Button (Play/Stop), Holder (Knob,Spring),
Knob (FF/REV) .......................................................... 8
3-2. LID, Case .................................................................... 7
3-3. Main Board, Power Board .......................................... 7
3-4. LCD Unit .................................................................... 8
3-5. Button (Play/Stop), Holder (Knob,Spring),
Knob (FF/REV) .......................................................... 8
4. TEST MODE
................................................................... 9
5. DIAGRAMS
5-1. Block Diagrams ......................................................... 11
5-2. Printed Wiring Boards (Main Section) ..................... 12
5-3. Schematic Diagram (Main Section (1/2)) ................. 13
5-4. Schematic Diagram (Main Section (2/2)) ................. 14
5-5. Printed Wiring Boards (Power Section) ................... 15
5-6. Schematic Diagram (Power Section) ........................ 16
5-2. Printed Wiring Boards (Main Section) ..................... 12
5-3. Schematic Diagram (Main Section (1/2)) ................. 13
5-4. Schematic Diagram (Main Section (2/2)) ................. 14
5-5. Printed Wiring Boards (Power Section) ................... 15
5-6. Schematic Diagram (Power Section) ........................ 16
6. EXPLODED VIEW
6-1. Main Section ............................................................. 21
6-2. Case Section ............................................................. 22
6-2. Case Section ............................................................. 22
7. ELECTRICAL PARTS LIST
................................... 23
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270
• Keep the temperature of the soldering iron around 270
°C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
TABLE OF CONTENTS
• Replacement of CXD9534BGG (IC710) used in the set requires a special
tool.
r
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the
lead-free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed
with the lead free mark due to their particular size.)
lead-free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed
with the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40
• Unleaded solder melts at a temperature about 40
°C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to
be applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set
to about 350
Ordinary soldering irons can be used but the iron tip has to
be applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set
to about 350
°C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder
may also be added to ordinary solder.
may also be added to ordinary solder.
SECTION 1
SERVICING NOTE
3
NW-E5
SECTION 2
GENERAL
LOCATION AND FUNCTION OF CONTROLS
This section is extracted from
instruction manual.
instruction manual.
(front)
(rear)
Display
1 Text/graphic information display
2 Play mode indication
3 AVLS indication
4 MEGA BASS indication
5 Battery remain indication
1 i (Headphones) jack
2 Display
3 PLAYMODE button
4 DISPLAY button
5 Bx (play/stop) button
6 Shuttle switch
7 VOLUME+/– button
8 MEGA BASS/AVLS button
9 HOLD switch
0 Dedicated USB jack
qa Strap hole for attaching the strap
qs Battery compartment
2
3
5
1
4
1
2
3
4
5
6
7
8
9
0
qs
qa
4
NW-E5
