DOWNLOAD Sharp XG-P20XE (serv.man4) Service Manual ↓ Size: 1.38 MB | Pages: 35 in PDF or view online for FREE

1. Feed the XGA mode 75-Hz

black signal.

2. Make the following choice:

Group : OUTPUT 3
Subject : SH-PHASE
(Have the standard level at
8.)
Fix the GCK-PHASE set-
tings all to 8.

»

Using the control switches or the remote controller
buttons, make sure that the “OUTPUT 3” charac-
ters are not blurry and there is no ghost image. If
such blur or ghost occurs, finely adjust the setting
in the range of 7~9.

1. Feed the black-and-red

(25%) stripe signal (XGA).

2. Make the following choice:

Group : OUTPUT 3
Subject : RC (R)

: BC (B)
: GC (G)

»

Using the control switches or the remote controller
buttons, adjust the data in order to minimize the
flicker.

»

Make the same adjustment for BC (B) and GC (G).

»

See if the image is equally adjusted at the center
and both sides of the screen. If not, readjust the
setting to have the image equal at right and left.

1. Feed the INFO COM. gray

scale and color bar pattern.

2. Make the following choice:

Group : OUTPUT 1
Subject : G1-BLK

»

Make sure that scale (white side) to No.251 and
scale (black side) to No.8 can be seen.

»

If white scale can't be seen properly, readjust with
G1-BLK.

4

8

12

249 251

1. Connect the oscilloscope to

TP1102 for red.

2. Make the following choice:

Group : OUTPUT 2
Subject : PSIG-H

: PSIG-L

»

Adjust the PSIG waveform to the one shown below.

»

For the green and blue colors, make sure their wave-
forms are similar to that of the red color.

2.5V DC

5.0V DC

GND

PSIG

(Adjust with PSIG-L.)

(Adjust with PSIG-H.)  

1. Feed the 32-step gray scale

signal (XGA 60Hz).
Group : OUTPUT 1
Subject : R1-BLK (R)

R1-GAIN(R)
B1-BLK (B)
B1-GAIN(B)

»

Adjust the R1-BLK and B1-BLK data for the black
balance on the gray scale. Then adjust the R1-
GAIN and B1-GAIN data for the center-to-white
balance on the gray scale.
(Adjust to the best point.)

1. Feed the NTSC mono-

scope pattern signal.

2. Group : VIDEO 1

Subject : NTSC-H

»

Using the control switches or the remote controller
buttons, adjust the data to have the same
overscan.

1. Feed the split color bar sig-

nal.
Group : VIDEO 1
Subject : PICTURE

2. Connect the oscilloscope

between pin TP1201and
GND.

»

Using the control switches or the remote controller
buttons, adjust the white to white (100%) level
difference to 2.2 

±

 0.05 Vp-p.

2.2Vp-p

1. Feed the split color bar sig-

nal.
Group : VIDEO 1
Subject : TINT

2. Connect the oscilloscope to

TP1301.

»

Using the control switches or the remote controller
buttons. Adjust the setting so that the points indi-
cated in the waveform figure are at the same level.

1. Feed the baseband (0 step

gray scale :0% Black to
100% White) signal.
Group : VIDEO 1
Subject : BRIGHT

2. Press the control switch or

the remote control’s mute
button (to set the gamma
correction to the process
setting).

»

Using the control switches or the remote controller
buttons, adjust the setting until the black signal (0%)
becomes bit-less.

SAME LEVEL

100% White Red

1. Feed the split color bar sig-

nal.
Group : VIDEO 1
Subject : N-COLOR

2. Connect the oscilloscope to

TP1101.

»

Using the control switches or the remote controller
buttons, adjust the difference between the 100%
white portion and the red portion to 0.25 

±

0.02 Vp-p.

   (same as 100% white)

1. Feed the PAL color bar sig-

nal.
Group : VIDEO 1
Subject : P-COLOR

2. Connect the oscilloscope to

TP1101.

»

Using the control switches or the remote controller
buttons, adjust the difference between the 100%
white portion and the red portion to 0.3 

±

0.02 Vp-p.

100% White Red

1. Feed the SECAM color bar

signal.
Group : VIDEO 1
Subject : S-COLOR

2. Connect the oscilloscope to

TP1101.

»

Using the control switches or the remote controller
buttons, adjust the data to have a level difference
of 0.3 

±

0.02 Vp-p between the 100% white portion

and the red portion.

1. Feed the NTSC mono-

scope pattern signal
Group : VIDEO 2
Subject : R1-BLK

B1-BLK

»

Using the control switches or the remote controller
buttons, adjust so that the entire screen looks
evenly colorless.

100% White Red

1. Feed the color bar signal of

the 480I component signal
to the BNC G(Y) input ter-
minal.

2. Select the following subject.

Group : DVD
Subject : CONTRAST

»

Using the control switches or the remote controller
buttons, adjust the white to white (100%) level
difference to 2.2 

±

 0.05v p-p.

2.2Vp-p

1. Feed the color bar signal of

the 480I component signal
to the BNC G(Y) input ter-
minal.

2. Select the following subject.

Group : DVD
Subject : CONTRAST

»

Using the control switches or the remote controller
buttons, adjust the setting until the black sig-
nal(0%) becomes bit-less.

1. Feed the color bar signal of

the 480I component signal
to the BNC Y, Pb and Pr in-
put terminals. Feed the
sync signal only for the Y
signal.

2. Select the following subject.

Group : DVD
Subject : TINT

3. Connect the oscilloscope to

TP1301.

1. Feed the color bar signal of

the 480I component signal
to the BNC G(Y) input ter-
minal.

2. Select the following subject.

 Group : DVD
Subject : COLOR

3. Connect the oscilloscope to

TP1101.

»

Adjust the level difference between the 100% white
and red portions to 0.3 

±

0.02 Vp-p.

100% White Red

1. Feed the NTSC mono-

scope signal to G(Y) input
terminal of the BNC termi-
nal.

2. Select the following subject.

Group : DVD
Subject : R1-BLK

B1-BLK

»

 Adjust so that a white balance may become the best
condition by using the control switch or  buttons of
the R/C.

1.The adjustment condition of

each item is as mentioned
in the following.
RGB input:Refer to No.11
VIDEO input:Refer to No.19
DVD input:Refer to No.23

»

Make sure that a white balance is the best condi-
tion.

»

Using the control switches or the remote controller
buttons. Adjust the setting so that the points indi-
cated in the waveform figure are at the same level.

SAME LEVEL