Sharp XG-P20XE (serv.man4) Service Manual ▷ View online
17
XG-P20XU
XG-P20XE
XG-P20XD
XG-P20XE
XG-P20XD
6. Removing the power / ballast / sound-out / bimetal unit assembly.
6-1. Remove the screw and disconnect the grounding wire from the shield case of the power/ballast unit.
6-2. Disconnect the connectors from the sound out PWB.
6-3. Take out the bimetal socket.
6-4. Remove the two screws and detach the lamp socket.
6-5. Remove the three screws and detach the power unit.
6-6. Remove the screw and slide the bimetal assembly upward out of position.
6-2. Disconnect the connectors from the sound out PWB.
6-3. Take out the bimetal socket.
6-4. Remove the two screws and detach the lamp socket.
6-5. Remove the three screws and detach the power unit.
6-6. Remove the screw and slide the bimetal assembly upward out of position.
6-5
6-1
6-2
6-3
6-3
6-6
6-4
Bimetal Ass'y
Sound Out PWB
Power/Ballast Unit
18
XG-P20XU
XG-P20XE
XG-P20XD
XG-P20XE
XG-P20XD
7-2
7-2
7-1
7-3
7-4
7-2
7-2
Optical Mechanism Unit
AC Inlet Unit
7. Removing the optical mechanism unit
7-1. Remove the two screws off the optical mechanism intake fan.
7-2. Remove the eight screws and take out the optical mechanism unit.
7-3. Remove the screw and disconnect the grounding wire.
7-4. Disconnect the connector and detach the AC inlet unit.
7-2. Remove the eight screws and take out the optical mechanism unit.
7-3. Remove the screw and disconnect the grounding wire.
7-4. Disconnect the connector and detach the AC inlet unit.
19
XG-P20XU
XG-P20XE
XG-P20XD
XG-P20XE
XG-P20XD
Condition
The internal
temperature is
abnormally high.
temperature is
abnormally high.
The lamp does
not light up.
not light up.
The POWER
indicator flashes
in red when the
projector is on.
indicator flashes
in red when the
projector is on.
Problem
· Blocked air intake.
· Clogged air filter.
· Cooling fan breakdown.
· Internal circuit failure.
· Cooling fan breakdown.
· Internal circuit failure.
· Burnt-out lamp.
· Lamp circuit failure.
· Lamp circuit failure.
· The bottom filter cover is
open.
Possible Solution
· Relocate the projector to an area with
proper ventilation.
· Clean the filter.
· Take the projector to your nearest Au-
· Take the projector to your nearest Au-
thorized Sharp Industrial LCD Products
Dealer or Service Center for repair.
Dealer or Service Center for repair.
· Carefully replace the lamp.
· Take the projector to your nearest Au-
· Take the projector to your nearest Au-
thorized Sharp Industrial LCD Products
Dealer or Service Center for repair.
Dealer or Service Center for repair.
· Securely install the bottom filter cover.
Maintenance Indicator
TEMPERATURE
WARNING indicator
WARNING indicator
LAMP REPLACE-
MENT indicator
MENT indicator
POWER indicator
• As the usage environment can vary significantly, the projector lamp may not operate for 1,500 hours.
ON
•Reset the lamp timer only after replacing the lamp.
Resetting the lamp timer
2
Connect the power
cord.
cord.
1
Reset the lamp timer.
Plug the power cord into the AC
socket of the projector.
socket of the projector.
While pressing
"
,
|
and
ENTER on the projector,press
POWER ON on the projector.
POWER ON on the projector.
“LAMP 0000H ” is displayed,
indicating that the lamp timer is
reset.
indicating that the lamp timer is
reset.
LAMP 0000H
Resetting the TOTAL LAMP TIMER
20
XG-P20XU
XG-P20XE
XG-P20XD
XG-P20XE
XG-P20XD
THE OPTICAL UNIT OUTLINE
Layout of the optical system
Note: Layout for positioning the optical system.
* The M3 mirrors have a coating
wedge (for different film thick-
ness). Set up these mirrors, with
their markings positioned as
shown above, so that their
coated faces and both sides be
in the correct directions.
ness). Set up these mirrors, with
their markings positioned as
shown above, so that their
coated faces and both sides be
in the correct directions.
B-LCD
G-LCD
GREEN
BLUE
BLUE
RED
R-LCD
Dichroic coating
(B transmission)
(B transmission)
Incident polarizing plate R
Dichroic coating
(R transmission)
(R transmission)
AL-coated mirror R
AL-deposited face
(R reflection)
Marking
Dichroic coating
(R, G transmission)
(R, G transmission)
Marking
G reflector
Dichroic coating
B/G reflector
AL-coated mirror W
AL-deposited
face
face
Fly-eye lens (outgoing light)
Fly-eye lens (incoming light)
UV-IR coating
UHP lamp
(Light source)
Relay lens 1
UV-absorption-filter
AL-deposited face
AL-coated mirror B
Projection Lens
AL-coated mirror B
Cross dichroic prism
Incident polarizing plate B
Relay lens 1
Relay lens 2
Incident polarizing plate G
Condenser lens G
PBS aperture
Condenser lens R
* M3
M6
G03
L2
G02
L2
G01
M4
M2
M5
M1
PBS(polarization
beam splitter)
beam splitter)
L1
1/2
λ
plate + polarizing plate
1/2
λ
plate
Sapphire glass
Polarizing plate
Polarizing plate
1/2
λ
plate
Sapphire glass
Polarizing plate
Polarizing plate
Sapphire glass
Polarizing plate
Polarizing plate
Click on the first or last page to see other XG-P20XE (serv.man4) service manuals if exist.