DOWNLOAD Sharp XG-C40XE (serv.man15) Service Manual ↓ Size: 15.33 MB | Pages: 115 in PDF or view online for FREE

2.0V DC

6.2

±

0.2V DC

PSIG

GND

(Adjust with PSIG-H.)

(Adjust with PSIG-L.)

1. Connect the oscilloscope to

TP1701 for red.

    TP1702 for green
    TP1703 for blue.

2. Make the following choice:

Group : OUTPUT 2
Subject : PSIG-H

: PSIG-L

»

Adjust the PSIG waveform to the one shown below.

»

For the green and blue colours, make sure their wave-
forms are similar to that of the red colour.

»

Make sure the pin stripe of every 12 dot doesn't ap-
pear at 10 steps signal of side nays.
(Appearing white pin stripe or black one, adjust the
PSIG-H.)

1. Project the XGA60Hz ghost

test pattern (black charac-
ters in bold on the halftone
RGB background).
Group: OUTPUT3

2. GCK-PHASE adjustment

Make sure the setting is fixed
at 8 (initial value).

3. EN-WIDTH adjustment

Make sure the setting is fixed
at 8 (initial value).

4. ENR-PHASE adjustment (R-

LCD ghost adjustment)

5. ENG-PHASE adjustment

(G-LCD ghost adjustment)

6. ENB-PHASE adjustment (B-

LCD ghost adjustment)

»

ENR-PHASE adjustment (R-LCD ghost adjustment)

1

Increase the setting until a ghost image (see
Note) becomes visible at the left of the back
characters on the R half-tone background.

2

Lower the setting point by point until the left-
hand ghost image (

1

 above) disappears.

3

Further lower the setting by one point.

»

ENG-PHASE adjustment (G-LCD ghost adjust-
ment)
Adjust the G ghost image by following the same
procedures described under step 1 above.

»

ENB-PHASE adjustment (B-LCD ghost adjust-
ment)
Adjust the B ghost image by following the same
procedures described under step 1 above.

Note: Left-hand ghost image: Characters are shown

double 12 dots left from the real characters.

Reference: This adjustment is made because the

EPSON LCD panel may have 1- or 2-
point differences due to lot-by-lot varia-
tions.

1. Feed the XGA mode 75-Hz

black signal.

2. Make the following choice:

Group : OUTPUT 3
Subject : SH-PHASE
(Have the standard level at
2.)
Fix the RCK-, GCK- and
BCK-PHASE settings all to
8.

»

Using the control switches or the remote controller
buttons, make sure that the “OUTPUT 3” charac-
ters are not blurry and there is no ghost image. If
such blur or ghost occurs, finely adjust the setting
in the range of 7~9.

1

2

2.0Vp-p

1. Feed the black-and-red

(25%) stripe signal (XGA).

2. Make the following choice:

Group : OUTPUT 3
Subject : RC (R)
and
Group : OUTPUT 3
Subject : RC-INV (R)

»

Using the control switches or the remote controller
buttons, adjust the data in order to minimize the
flicker.

»

Make the same adjustment for BC (B), GC (G),
RC-INV (B) and RC-INV (G).

»

See if the image is equally adjusted at the center
and both sides of the screen. If not, readjust the
setting to have the image equal at right and left.

1. Feed the green-only SMPTE

pattern signal (XGA).
Group : OUTPUT 1
Subject : G1-BLK

»

Adjust the G-BLK data until the gradation of the
portion 

1

 (95% and 100% white) shown below

can be slightly recognized.  Make sure also that the
gradation of the portion 

2

 (0% and 5% black) is

visible.

1. Feed the 32-step gray scale

signal (XGA).
Group : OUTPUT 1
Subject : R1-BLK (R)

B1-BLK (B)

»

Choose the subjects R1-BLK and B1-BLK and
adjust the black balance of the gradation.

1. Feed the NTSC monoscope

pattern signal.

2. Group : VIDEO 2

Subject : N358-DLY     (4)

N443-DLY     (0)
PAL-DLY       (3)
SECAM-DLY (0)

Make sure the settings are

    as above.
3. Group : VIDEO 1

Subject : NTSC-H

»

Using the control switches or the remote controller
buttons, adjust the data to have the same
overscan.

1. Feed the split colour bar sig-

nal.
Group : VIDEO 1
Subject : PICTURE

2. Connect the oscilloscope

between pin (2) of P801 and
GND.

»

Using the control switches or the remote controller
buttons, adjust the black-to-white (100%) level
difference to 2.0 

±

0.02 Vp-p.

100% White Red

100% White Red

100% White Red

1. Feed the baseband (split

colour bar) signal. (The ON-
AIR signal is not accepted
because of its too much
noise.)
Group : VIDEO 2
Subject : VROS/VGOS/VBOS

2. Press the control switch or

the remote control’s mute
button (to set the gamma
correction to the process
setting).

»

Using the control switches or the remote controller
buttons, adjust the setting until the black signal
becomes bit-less.

1. Feed the split colour bar signal.

Group : VIDEO 1
Subject : AGC

»

Using the control switches or the remote controller
buttons, adjust the setting until the white signal
becomes bit-less.

1. Feed the split colour bar

signal.
Group : VIDEO 1
Subject : TINT

2. Connect the oscilloscope to

pin (4) of P801.

»

Using the control switches or the remote controller
buttons, adjust the data to have the -(B-Y) wave-
form downhill straight.

»

After adjusting, adjust the
value of TINT up 3 point.

1. Feed the split colour bar sig-

nal.
Group : VIDEO 1
Subject : N-COLOR

2. Connect the oscilloscope to

pin (1) of P801.

»

Using the control switches or the remote controller
buttons, adjust the difference between the 100%
white portion and the red portion to 0.00 

±

0.05 Vp-p.

   (same as 100% white)

1. Feed the PAL colour bar sig-

nal.
Group : VIDEO 1
Subject : P-COLOR

2. Connect the oscilloscope to

pin (1) of P801.

»

Using the control switches or the remote controller
buttons, adjust the difference between the 100%
white portion and the red portion to 0.2 

±

0.05 Vp-p.

1. Feed the SECAM colour bar

signal.
Group : VIDEO 1
Subject : S-COLOR

2. Connect the oscilloscope to

pin (1) of P801.

»

Using the control switches or the remote controller
buttons, adjust the data to have a level difference
of 0.2 

±

0.05 Vp-p between the 100% white portion

and the red portion.

1. Feed the NTSC 10-step sig-

nal.

2. Select the following group

and subject.
Group: VIDEO2
Subject: R1-GAIN

B1-GAIN

3. Connect the oscilloscope to

TP1101 (R) and TP1201 (G).

4. For the blue colour, con-

nect the oscilloscope to
TP1301 (B) and TP1201
(G).

»

Select R1-GAIN and adjust the setting so that the
R and G signals have the same amplitude.

»

For the blue colour, adjust the setting the same
way.

1. Feed the NTSC monoscope

pattern signal
Group : VIDEO 2
Subject : R1-BLK

B1-BLK

»

Using the control switches or the remote controller
buttons, adjust so that the entire screen looks
evenly colourless.

1. Feed the monoscope pattern

signal.

2. Group: DTV

Subject: CR-OFFSET

CB-OFFSET

»

Using the control switches or the remote controller
buttons, adjust so that the entire screen looks
evenly colourless.

1. Group: VIDEO1

Subject: SET UP B

SET UP C

»

Make sure the settings are 11 for SET UP B and 2
for SET UP C.

1. Using the colour correction

system (ccdc), apply auto-
matic colour correction.

»

Make sure there is no noticeable colour irregularity
left on the screen.

1. Receive the colour bar sig-

nal.

»

In the process mode and select L1. Check the col-
our and tint.

1. Receive the monoscope pat-

tern signal.

»

In the process mode and select L2. Check the pic-
ture, brightness and sharpness.

»

In the process mode nad select L3. Check the bass,
treble.