Sharp MX-M654N / MX-M754N (serv.man2) Handy Guide ▷ View online
SHARP
INITIAL SETUP
13
PERIPHERAL / OPTION CONFIGURATION
FINISHER OPTION – MX-FN17, MX-FN19, MX-FN20, MX-FN21, MX-FN22
Sim 03-10 Saddle Fold/Staple Position Adjustment [MX-FN20/22 only]
Sim 26-65 Finisher Alarm Mode:-
Limit number of Copies in staple mode
(ON/OFF).
EXTERNAL ACCOUNTING MODULE – MX-AMX3
Sim 55-03 Auto clear function before Copy job execution:-
SSW 1-5
0 = Disable, 1 = Enable.
Sim 55-03 Continuous print mode (job queuing for OSA):-
SSW 24-7
0 = Disable, 1 = Enable.
MFP DATA BACKUP
Sim 22-06 Data Simulation Print.
Device Clone & Storage Backup.
Sim 56-01 Backup EEPROM Data to HDD.
GREY BALANCE & DENSITY ADJUSTMENT
SHARP
14
Automatic Grey Balance Calibration - FACTORY MODE
Note: When adjusting grey balance adjustment before or after routine maintenance, always use the
recommended paper (Mondi 90gsm or equivalent) for optimum image quality.
HIGH DENSITY PROCESS CONTROL:
[Execute]
Sim 44-06
HALFTONE PROCESS CONTROL:
[Execute]
Sim 44-26
GREY BALANCE ADJUSTMENT:
Sim 46-74 [Engine & Printer]
FACTORY MODE
Place printed test pattern onto glass for both Copy &
Printer modes.
Manual Grey Balance Calibration – SERVICE MODE
HIGH DENSITY PROCESS CONTROL:
[Execute]
Sim 44-06
HALFTONE PROCESS CONTROL:
[Execute]
Sim 44-26
GREY BALANCE ADJUSTMENT:
Sim 46-74 [Engine & Printer]
SERVICE MODE
Place printed test pattern onto glass for both Copy &
Printer modes.
GREY BALANCE MANUAL ADJUSTMENT:
Sim 46-21 [for Engine]
Sim 67-25 [for Printer]
Adjust K (17 points) for Copy & Printer Modes.
SHARP
GREY BALANCE & DENSITY ADJUSTMENT
15
PRINTER DENSITY CHECK:
Sim 64-05 [PCL Printer]
Sim 64-06 [PS Printer]
SERVICE TARGET SETTING:
Sim 63-07 [for Engine]
Sim 67-27 [for Printer]
Scan Test Pattern to Register Custom Service Target
DEFAULT SETTING (Service Mode):
To return machine to “Standard” setting:-
STANDARD SERVICE TARGET SETTING:
[Execute]
Sim 63-08 [for Engine]
Sim 67-28 [for Printer]
GREY BALANCE ADJUSTMENT:
Sim 46-74 [Engine & Printer]
SERVICE MODE
Place printed test pattern onto glass for both Copy &
Printer modes.
MAINTENANCE
SHARP
16
Maintenance Indications:
DK
OPC DRUM (Counter) has reached
the specified life.
Replace OPC Drum
Process
Section
(Drum)
VK
BLACK DEVELOPER (Counter) has reached
the specified life.
Replace Developer.
Process
Section
(Developer)
MC
MAIN CHARGE Unit Counter has reached
the specified limit.
Replace Main Charger Kit
Process
Section
FK1
FUSING ROLLER Print Counter has reached
the specified limit.
Replace the Fusing
Heat Roller Kit.
Fuser
Section
FK2
PRESSURE ROLLER Print Counter has
reached the specified limit.
FK3
Fusing UPPER WEB Cleaner (Counter) has
reached the specified limit
(Pop Up FK3 Error – Web End Detected)
Replace the
Web Cleaning Kit
FK4
Fusing LOWER WEB Cleaner (Counter) has
reached the specified limit
(Pop Up FK4 Error – Web End Detected)
TK1
TRANSFER BELT Counter has reached
the specified limit.
Replace Transfer Belt Kit
Transfer
Section
TK4
TRANSFER ROLLER Counter has reached
the specified limit.
TA
Maintenance [All] Counter has reached specified limit
Starting Powder:
The following starting powder should be applied to the relevant consumable item during maintenance:-
Starting Powder
OPC Drum
Transfer Belt
MX-M654N
MX-M754N
MX-M754N
Apply CKOG-0345DS51
[Yellow Toner] on top of
UKOG-0312FCZZ [Stearic Acid]
None
Click on the first or last page to see other MX-M654N / MX-M754N (serv.man2) service manuals if exist.