Sharp MX-M623U / MX-M753U (serv.man7) Service Manual ▷ View online
MX-M753N MX-CF10 4 – 10
4)
Turn the front and the rear side adjustment bolts with the span-
ner removed in step 1) so that the upper and the lower clear-
ances are the same.
ner removed in step 1) so that the upper and the lower clear-
ances are the same.
5)
Check that the upper and the lower clearances are even when
viewed from the front and the back.
viewed from the front and the back.
6)
Tighten the front and the rear side adjustment section fixing
screws (2 pcs. for each side).
screws (2 pcs. for each side).
7)
Install the base cover (front and rear).
8)
Return the spanner to the original position.
M. Install the plate
1)
Hang the plate on the rear lower side of the inserter as shown
in the figure, and fix it with the fixing screw G (1 pc).
in the figure, and fix it with the fixing screw G (1 pc).
* At that time, check to insure that the upper and lower posi-
tioning tabs are in the plate holes.
NOTE: The plate and the connection plate are common to the fin-
isher. Please reuse rail and connector plate for inserter.
N. Turn on the power of the main unit
1)
Insert the power plug of the main unit into the power outlet.
2)
Open the front cabinet.
Turn ON the power switch in the front cabinet of the main unit.
Turn ON the power switch in the front cabinet of the main unit.
3)
Turn ON the power switch on the operation panel.
ON
MX-M753N MX-FN15/FN16 5 – 1
MX-M753N
Service Manual
[5] MX-FN15/FN16
1. Unpacking
When removing or moving, be sure to perform by two persons not
to drop the unit.
to drop the unit.
A. Removal of the finisher
1)
Remove the fixing member and remove the top case.
2)
Remove the packaged parts from the add.
3)
Hold the upper section of the machine with two persons, and
pull it up and stand it straight.
pull it up and stand it straight.
(The finisher is very heavy. Be careful.)
4)
Remove the tape and the skid.
5)
Remove the upper packing material.
6)
One person holds the machine so that it does not fall down.
The other person tilts the machine a little to remove packing
material.
The other person tilts the machine a little to remove packing
material.
7)
Bring the base of the unit into contact with the floor so that it
does not fall down.
(Be careful the base section can shift when the packing mate-
rial has been removed.)
does not fall down.
(Be careful the base section can shift when the packing mate-
rial has been removed.)
MX-M753N MX-FN15/FN16 5 – 2
8)
Tilt the machine to the opposite side a little, and remove pack-
ing material on the opposite side.
ing material on the opposite side.
9)
Slowly bring the base section of the machine on the opposite
side to contact with the floor.
side to contact with the floor.
10) Remove the vinyl cover.
B. Removal of the fixing member
Remove the tape from the finisher.
Remove the shipment locking material with red the note.
1)
Remove the shipment locking material with red the note.
1)
Remove the tape.
2)
Remove the tape and remove the protection board and the
sheet.
sheet.
3)
Remove the tape and open the upper cover.
4)
Remove the tape and remove the transit fixing member and
the sheet.
the sheet.
5)
Remove the tape and remove the lower tray transit fixing
member.
member.
1
1
2
1
2
1
MX-M753N MX-FN15/FN16 5 – 3
6)
Remove the tape and the fixing member.
7)
Remove the tape and remove the jam release door transit fix-
ing member.
ing member.
8)
Remove the tape and remove the jam release door handle
section transit fixing member.
section transit fixing member.
9)
Remove the power cable fixing tape.
10) Open the upper front door, and remove the staple transit fixing
member.
11) Open the lower door, and remove the tape.
12) Pull out the stitcher remove the screw, and remove the stitcher
transmit fixing member.
13) Remove the screw, and remove the lower cover.
14) Remove the screw, and remove the transit fixing members F
14) Remove the screw, and remove the transit fixing members F
and R.
15) Remove the screw, and remove lift tray rail section transit fix-
ing members (4 positions).
1
2
3
1
2
1
2
2
2
1
2
2
Click on the first or last page to see other MX-M623U / MX-M753U (serv.man7) service manuals if exist.