DOWNLOAD Sharp MX-M623U / MX-M753U (serv.man7) Service Manual ↓ Size: 13.53 MB | Pages: 104 in PDF or view online for FREE

MX-M753N  MX-FN15/FN16  5 – 4

1)

Check that all the items are included in the package.

<Note before installation>
* Before starting installation, check to insure that the data lamp on

the operation panel does not light up or blink.

1)

Turn OFF the power switch on the operation panel.

2)

Open the front cabinet.
Turn OFF the power switch in the front cabinet of the main unit. 

3)

Disconnect the power plug of the main unit from the power out-
let.

1)

Attach the positioning pin with two fixing screws I to the left
upper section of the main unit. Be careful to the attachment
direction of the positioning pin.

2)

Attach the earth plate with the fixing screws H (2 pcs.) to the
left lower section of the main unit.
In this case, attach so that the R mark on the earth plate faces
up.

3)

Pull out the lock release lever on the left side of the main unit,
and open the left door.

4)

Remove the paper exit cover on the upper side of the left door.

5)

Close the left door.

1

Positioning pin

1 pc.

6

Screw G (M4 x 8)

3 pcs.

2

Earth plate

1 pc.

7

Screw H (M4 x 14)

2 pcs.

3

Earth mounting plate

1 pc.

8

Screw I (M4 x 18)

4 pcs.

4

Rail mounting plate

1 pc.

9

Punch position label

2pcs.

5

Staple label

2 pcs.

1

2

5

6

3

4

8

7

9

OFF

F

R

2

1

MX-M753N  MX-FN15/FN16  5 – 5

6)

Install the connection plate to the main unit with the fixing
screws I (2 pcs.).

1)

Install the plate to the finisher as shown in the figure, and fix it
with the fixing screw G (1 pc).

2)

Install the rail and the finisher with two screws G (M4 x 6).

1)

Bring the finisher closer to the main unit and check that the
guide pin of the main unit enters into the connection hole in the
finisher smoothly.

2)

At that time, check that the center of the guide pin is in the cen-
ter of the scale marked on the side of the connection hole, and
the pin direction coincides with the hole direction.

3)

If the guide pin is not in the center, or if the guide pin does not
enter smoothly, adjust as follows.

4)

Remove the fixing screw of base cover (2 positions) in the front
and the back of the finisher, and remove the base cover.

5)

Remove the fixing screws (2 pcs.) of the rear cover on the rear
of the finisher, and remove the rear cover.

6)

Only for the AR-F15, remove the front cabinet lower fixing
screws (2 pcs.).

7)

Open the front cabinet upper, and open the front cabinet lower.

MX-M753N  MX-FN15/FN16  5 – 6

8)

Loosen the fixing screws (2 pcs for each) of four casters.

9)

Remove the spanner stored inside of the front cabinet upper.

10) Turn the bolt with the removed spanner so that the guide pin is

in the specified range of the scale.

(At that time, lift the finisher a little, and the bolt can be turned
manually.)

11) After completion of the adjustment, tighten the caster fixing

screws (8 pcs.).

12) Close the front cabinet lower and the front cabinet upper.

13) Check to insure that the intervals at the upper and the lower

sides of the main unit and the finisher are even.

14) Attach the foot covers in front and at the back of the finisher

and the rear cover on the rear side, and tighten all the fixing
screws.

MX-M753N  MX-FN15/FN16  5 – 7

Attach the staple position label as shown in the figure.

1)

Remove the connector cover fixing screw for connection of the
finisher joint harness connector, and remove the connector
cover.

2)

Connect the finisher relay harness connector to the main unit
connector, and tighten the screw on the connector to fix.

1)

Insert the power plug of the main unit into the power outlet.

2)

Open the front cabinet.
Turn ON the power switch in the front cabinet of the main unit.

3)

Turn ON the power switch on the operation panel.

1)

Remove the rear cabinet of the finisher.

2)

Turn on the power of the main unit.

3)

Raise the DIP switch 1, 2, 4, 5, and 6 on the rear of the fin-
isher.

4)

Press SW1 button (left side) of the PWB. (It is located over the
DIP switch.)
* The finisher tray moves to the screw fixing position.

5)

Turn off the power of the main unit.

6)

Reset the DIP switch to the original state.

7)

Install the cabinet.

8)

Install the lift tray rail section fixing members (4 positions) with
four screws.

1

2

3

ON

When unpacking

Before packing (Shifted to
the screw fixing position.)