Sharp MX-M623U / MX-M753U (serv.man7) Service Manual ▷ View online
MX-M753N MX-CF10 4 – 2
4)
Remove the tape and open the base cover.
5)
Remove the connector cable fixing tape.
C. Check the packed items
1)
Check that all the items are included in the package.
* Uses only when the MX-FN14 is installed.
2. Installation
<Note before installation>
* Before starting installation, check to insure that the data lamp on
* Before starting installation, check to insure that the data lamp on
the operation panel is not on or blinking.
A. Turn off the power of the main unit
1)
Turn OFF the power switch on the operation panel.
2)
Open the front cabinet.
Turn OFF the power switch in the front cabinet of the main unit.
Turn OFF the power switch in the front cabinet of the main unit.
3)
Disconnect the power plug of the main unit from the power out-
let.
let.
Parts name
Quantity
1
Positioning plate
1
2
Upper limit regulation wire
1
3
Button cover
1
4
Screw C (M4 x 12 small screw bind)
3
5
Screw D (M3 x 8 tapping bind)
2
6
Screw E (M4 x 7 small screw bind)
2
7
Screw F (M4 x 14 tapping bind)
2
8
Screw G (M4 x 12 tapping bind)*
1
9
Screw H (M4 x 6 small screw bind)*
1
10
Interlock pin*
1
11
Grip blinding sheet*
1
1
3
4
5
9
6
7
8
11
10
2
OFF
MX-M753N MX-CF10 4 – 3
B. When the finisher or the saddle finisher is
installed
* If it is not installed, perform procedure C..
(1) Removal of the connector between the main unit
and the finisher
1)
Remove the screw from the finisher connector connected to
the left side of the main unit.
the left side of the main unit.
2)
Disconnect the finisher connector.
(2) Removal of the rail, the connectting plate, and the
earth plat
1)
Separate the finisher and the main unit.
2)
Remove two screws which are fixing the connecting plate
under the finisher.
under the finisher.
3)
Remove the plate (fixed by one screw) from the rear lower sec-
tion of the finisher.
tion of the finisher.
4)
Go to procedure D..
C. When the finisher and the saddle finisher are
not installed to the main unit
(1) Attach the positioning pin and the earth plate to
the main unit. (Use the packaged parts of the
finisher.)
finisher.)
1)
Remove the connector cover fixing screw for connection of the
finisher joint harness connector, and remove the connector
cover.
finisher joint harness connector, and remove the connector
cover.
* Only when the finisher and the inserter are installed
together, perform this procedure.
1
2
1
2
1
2
MX-FN15/FN16
MX-FN14
MX-M753N MX-CF10 4 – 4
2)
Attach the positioning pin with two fixing screws I to the left
upper section of the main unit. Be careful to the attachment
direction of the positioning pin.
upper section of the main unit. Be careful to the attachment
direction of the positioning pin.
NOTE: For fixing screws H and I, use the packaged parts of the
MX-FN14/FN15/FN16.
3)
Attach the earth plate with the fixing screws H (2 pcs.) to the
left lower section of the main unit.
In this case, attach so that the R mark on the earth plate faces
up.
left lower section of the main unit.
In this case, attach so that the R mark on the earth plate faces
up.
4)
Pull out the lock release lever on the left side of the main unit,
and open the left door.
and open the left door.
5)
Remove the paper exit cover on the upper side of the left door.
6)
Close the left door.
7)
Attach the connecting plate to the with fixing screws I (2 pcs.)
main unit.
main unit.
D. Install the positioning plate and the button
cover to the finisher
1)
Remove the step screw (1 pc) and the screws (2 pcs.) which
are fixing the punch cover.
are fixing the punch cover.
2)
Attach the interlock pin (1 pc.) to the mounting plate with a
screw H (1 pc.).
Fit the holes of the screws removed in step 1) with the screw
holes of the positioning plate, and fix it with the three fixing
screws C.
screw H (1 pc.).
Fit the holes of the screws removed in step 1) with the screw
holes of the positioning plate, and fix it with the three fixing
screws C.
3)
Install the button cover with the lock button fixing screws D (2
pcs.) to hide the lock button on the top of the punch cover.
pcs.) to hide the lock button on the top of the punch cover.
F
R
2
1
Use positions
MX-M753N MX-CF10 4 – 5
E. Install the upper limit regulation wire to the
inserter
1)
Open the front door of the inserter, and install the upper limit
regulation wire with the two fixing screws E.
regulation wire with the two fixing screws E.
F. Install the inserter to the finisher
1)
Open the front door of the inserter, and loosen the lock fixing
screw until the screw is released.
screw until the screw is released.
2)
Stand the tray.
3)
Hold the lower section of the front cabinet and the grip of the
rear cabinet as shown in the figure, tilt the inserter a little so
that the indication hole in the inserter support section is fit with
the metal fixture of the finisher connecting plate installing sec-
tion, and install it.
rear cabinet as shown in the figure, tilt the inserter a little so
that the indication hole in the inserter support section is fit with
the metal fixture of the finisher connecting plate installing sec-
tion, and install it.
* At that time, check that the finisher lock lever is engaged on
the inserter groove securely.
4)
Tighten the fixing screw of the inserter lock to fix the inserter
and the finisher.
and the finisher.
Click on the first or last page to see other MX-M623U / MX-M753U (serv.man7) service manuals if exist.