Sharp MX-M266N / MX-M316N / MX-M356N (serv.man5) Service Manual ▷ View online
MX-M265N MX-FN26 (FINISHER) 7 – 6
30) Install the finisher front cover from the left side by sliding, and
close the finisher front cover and the machine front cover.
31) Install the paper holding arm.
32)Connect the machine connection connector.
33) Attach the staple position label to the document feed unit.
2
: ‘15/Aug.
2
MX-M316N MX-TR17 (EXIT TRAY UNIT) 8 – 1
MX-M316N
Service Manual
[8] MX-TR17 (EXIT TRAY UNIT)
1. Packed items
2. Installation
NOTE: Turn off the main switch of the machine and then remove
the power plug of the machine from the outlet.
1)
Remove two EPE cushions.
2)
Remove the mylar. (Other than the North America)
3)
Remove five screws and remove the rear cabinet.
4)
Remove screws and remove the right cabinet middle.
5)
Insert the harness of the right paper exit unit to the hole of the
second paper exit.
second paper exit.
NOTE: Wire the harness to the upper of the rib.
If wiring it to the under of the rib, the harness may
come into contact with the gear.
come into contact with the gear.
6)
Insert the pawl of the right paper exit unit to the oval hole of the
frame of the main unit.
frame of the main unit.
Insert the positioning boss of the main unit to the round hole in
lower side.
lower side.
0APER
0APER
0APER
(ARNESS
3CREW
0APER
RIGHT
2IGHT
EXIT
3CREW
3CREW
MX-M316N MX-TR17 (EXIT TRAY UNIT) 8 – 2
7)
When tightening the screw, tighten in the sequence of (A), (B),
(C) and (D).
(C) and (D).
8)
Fix the harness to the wire saddles and connect the connector
of the harness to the MPFPC PWB.
of the harness to the MPFPC PWB.
9)
Install the paper exit right cover sub and tightening the screw.
10) Install the right paper exit actuator and the paper holding arm.
A
B
C
D
Insert the actuator to
the holes of righjt paper
exit part (R/F side).
the holes of righjt paper
exit part (R/F side).
Paper holing arm
Right paper exit
actuator
actuator
Right paper exit paper
full detection point
full detection point
Paper insert
direction
direction
MX-TR18 (JOB SEPARATOR) 9 – 1
Service Manual
[9] MX-TR18 (JOB SEPARATOR)
1. Parts included
2. Installation
NOTE: Turn off the main switch of the machine and then remove
the power plug of the machine from the outlet.
1)
Remove the rear cabinet.
2)
Remove the right cabinet middle and the right cover bottom.
3)
Install the second paper exit UN.
M4 x 8 S tight (2pcs)
4)
Pass the harness (packed together with the unit) of the second
paper exit unit though inside of the frame plate as shown in the
figure.
paper exit unit though inside of the frame plate as shown in the
figure.
Install the second paper exit unit to the machine, and fix it with
the screws which are packed together with the finisher. Con-
nect the connector of the harness.
the screws which are packed together with the finisher. Con-
nect the connector of the harness.
5)
Connect the connector of the harness to the PWB.
Job sepa r ator unit
Right door paper
guide
guide
Second paper exit
unit
unit
P-TIGHT
M4 x 10 (1 pcs.)
M4 x 10 (1 pcs.)
S-TIGHT
M4 x 8 (2 pcs.)
M4 x 8 (2 pcs.)
3
: ‘16/Jun.
3
Click on the first or last page to see other MX-M266N / MX-M316N / MX-M356N (serv.man5) service manuals if exist.