Sharp MX-M266N / MX-M316N / MX-M356N (serv.man5) Service Manual ▷ View online
MX-M265N MX-FN26 (FINISHER) 7 – 2
4)
Remove the actuator.
5) Remove the screw which are fixing the paper exit tray.
Remove the paper exit tray.
6)
Remove the paper exit rear cabinet support plate.
7) Remove the screws, and remove the front cabinet left.
8)
Remove the paper exit dummy cover.
9)
Remove the screw and remove the rear cabinet.
10) Remove the right cabinet middle unit.
11) Pass the harness (packed together with the unit) of the second
paper exit unit though the cable saddle and inside of the frame
plate as shown in the figure.
plate as shown in the figure.
Install the second paper exit unit to the machine, and fix it with
the M4 screws which are packed together with the finisher.
Connect the connector of the harness.
the M4 screws which are packed together with the finisher.
Connect the connector of the harness.
2
: ‘15/Aug.
2
2
2
2
2
2
2
MX-M265N MX-FN26 (FINISHER) 7 – 3
12) Connect the connector of the harness to the PWB.
13)Remove the current the second paper exit right door unit and fix
the bundled second paper exit right door unit to the right cabinet
middle unit.
middle unit.
14)Fix the right cabinet middle.
15) Remove round-head screw from the connection unit which is
packed with the finisher, and remove the front cabinet lower
and the connection cabinet temporarily.
and the connection cabinet temporarily.
16) Slide the rail under the connection unit to the lock position.
17) Engage the finisher connection plate with the notch in the stay
at the right bottom of the machine.
Slide the connection plate to the bottom, and attach M3 screw
as shown. (Use the screw bundled to the package.)
as shown. (Use the screw bundled to the package.)
MEMO: Press the right side of the connection plate.
MEMO: The black mylar should not be on the metal plate of
MFP.
MFP.
1
: ‘15/May
1
2
: ‘15/Aug.
2
2
2
1
MX-M265N MX-FN26 (FINISHER) 7 – 4
18) After attaching the screw, pull the connection plate toward you.
MEMO: When holding the finisher, hold the front frame side
and the rear frame side.
and the rear frame side.
19) Insert the finisher along the connection plate rail from the left
side of the machine until it locks.
20)Press the finisher from the front to slide to the rear together with
the connection plate.
MEMO: Press the right side of the connection plate.
21) Fix the connection plate from the front with the M3 screw which
are packed with the finisher.
22) Install the finisher connection cabinet from the left. And, install
the finisher front cabinet lower with screw.
23)Fix the FIN transmission harness with the bundled hexagonal
screws.
2
: ‘15/Aug.
2
2
MX-M265N MX-FN26 (FINISHER) 7 – 5
24) Fix the clamp of the FIN transmission harness to the frame and
fix the earth cable with the bundled screw.
25)Remove the dummy connector and connect the harness of the
FIN transmission harness. Then, connect the other harness to
the PWB.
the PWB.
26) Install the rear cabinet to the original position, and fix it with
screw.
27)Install the left cabinet to the original position.
28) Cut the part shown in the figure for the connector from the fin-
isher.
29)Install the front cabinet left to the original position.
2
: ‘15/Aug.
2
2
Click on the first or last page to see other MX-M266N / MX-M316N / MX-M356N (serv.man5) service manuals if exist.