Sharp MX-M266N / MX-M316N / MX-M356N (serv.man5) Service Manual ▷ View online
MX-M316N AR-DS19/DS20 (LOW STAND/HIGH STAND) 5 – 2
3)
<AR-DS19>
Fix the Stand with the MX-CS12 or the main unit with the MX-
CS12 by the Fixing screw B.
Fix the Stand with the MX-CS12 or the main unit with the MX-
CS12 by the Fixing screw B.
<AR-DS20>
Fix the Stand with the MX-CS12 or the MX-CS13 by the Fixing
screw B.
Fix the Stand with the MX-CS12 or the MX-CS13 by the Fixing
screw B.
4)
Fix the tray of MX-CS12 or MX-CS13.
5)
Remove the rear cover of the MX-CS12 or MX-CS13
6)
Fix the Fixing plate Rear with caring the fixing direction as
shown in the figure and the Fixing screw A/B.
shown in the figure and the Fixing screw A/B.
<AR-DS19>
<AR-DS20>
Fixing screw B
Fixing screw B
Fixing screw B
Fixing screw B
Fixing screw B
Fixing screw A
Fixing screw B
Fixing screw A
Fixing screw B
Fixing screw A
Fixing screw B
Fixing screw A
5
: ‘16/Dec.
5
MX-M316N AR-DS19/DS20 (LOW STAND/HIGH STAND) 5 – 3
7)
Fix the rear cover of the MX-CS12 or MX-CS13.
8)
Rotate the adjusters to fix the machine to the floor surface not
to move the machine.
to move the machine.
<AR-DS19>
<AR-DS20>
IC card reader 6 – 1
Service Manual
[6] IC card reader
1. Preparation
A. Supported IC card readers
B. Necessary parts
MEMO: There are two kinds of card reader holders. Choose the
suitable one according to the card reader to be installed.
suitable one according to the card reader to be installed.
2. Installation
NOTE: Before installation, be sure to turn both the operation and
main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.
A. Operation panel cabinet left removal
1)
Remove the operation panel cabinet left.
B. Attachment to the IC card reader holder
1)
Attach the card reader fixing tape to the IC card reader holder
referring to the notches as the reference.
referring to the notches as the reference.
NOTE: The holder type and the attachment procedure differ
depending on the kind of the IC card reader.
Holder type B
RDR-6081AKU, TWN3, RDR-7582AKU
Vertical direction: Fit with the notch.
Horizontal direction: Fit with the notch and the lower edge.
Horizontal direction: Fit with the notch and the lower edge.
Holder type C
Y591-EHID-201 v01
Vertical and horizontal directions: Fit with the notches.
2)
Cut out the boss.
Holder type B
RDR-6081AKU, RDR-7582AKU
NOTE: Don't cut the boss in case of TWN3 installation.
No.
Manufacturer
Model Name
1
RFIDeas
RDR-6081AKU
2
Equitrac
Y591-EHID-201 v01
3
Elatec
TWN3
4
RFIDeas
RDR-7582AKU
No.
Parts code
Parts name
Price rank
Q’ty
1
LHLDZ0171QSZZ
IC Card reader holder B
1
2
LHLDZ0172QSZZ
IC card reader holder C
1
3
PTPE-0352FCZZ
Card reader fixing tape
(Double-stick tape)
(Double-stick tape)
AP
2
4
DHAI-4709FCPZ
USB mini harness-AR
BP
1
5
LBNDJ0013FCZ1
Binding band
AE
1
6
XEBS730P08000
Screw (M3 x 8 P tight)
AC
2
7
LBNDJ0071FCZZ
Binding band
AC
2
Parts code
Parts name
Supported IC card
LHLDZ0171QSZZ
IC card reader holder B
RDR-6081AKU, TWN3,
RDR-7582AKU
RDR-7582AKU
LHLDZ0172QSZZ
IC card reader holder C
Y591-EHID-201 v01
1
2
3
4
1
2
3
4
5
7
6
IC card reader 6 – 2
3)
Attach the IC card reader to the IC card reader holder accord-
ing to the attachment reference ribs.
ing to the attachment reference ribs.
NOTE: The attachment reference position differs depending
on the kind of the IC card reader.
Holder type B
RDR-6081AKU, RDR-7582AKU
(The attachment reference position is the same in case of
the above model.)
(The attachment reference position is the same in case of
the above model.)
Holder type B
TWN3
(No reference position)
(No reference position)
Holder type C
Y591-EHID-201 v01
(No reference position)
(No reference position)
4)
Warp the harness of the IC card reader around the holder.
Then, attach the IC card reader holder to the operation panel
cabinet left.
Then, attach the IC card reader holder to the operation panel
cabinet left.
NOTE: Cable length is differs depending on type of card
reader, warp the cable followed by the following
instructions.
instructions.
Adjust the bind length of card reader cable and warp it with
banding band.
banding band.
Fix the banding band by inserting the lock part of it into the
hole in the frame.
hole in the frame.
Connect the USB mini harness to the card reader cable.
Click on the first or last page to see other MX-M266N / MX-M316N / MX-M356N (serv.man5) service manuals if exist.