DOWNLOAD Sharp MX-FX15 Service Manual ↓ Size: 598.64 KB | Pages: 57 in PDF or view online for FREE

MX-FX15  FAX SOFTWARE SWITCH  2 – 17

100

1-4

Calling

ID (number) setting
<Input the 1st digit 
when dial inputting and 
dialing>

Conduct ID No. setting when the PBX function is valid.
Valid when ID is set using SW99-7, 8.
The initial value of 0 is reverted to if a value outside of the setting range (10 - 
15) is set.

FAX initial setting

5-8

Calling

ID (number) setting 2
<Input the 2nd digit 
when dial inputting and 
dialing>

Conduct ID No. setting when the PBX function is valid.
Valid when ID is set using SW99-7, 8.
When 10 - 12, 14, 15 are designated, do not use numbers with those digits.
"-" when 13 is set.

FAX initial setting

101

1-4

Calling

ID (number) setting 3
<Input the 3rd digit 
when dial inputting and 
dialing>

Conduct ID No. setting when the PBX function is valid.
Valid when ID is set using SW99-7, 8.
When 10 - 12, 14, 15 are designated, do not use numbers with those digits.
"-" when 13 is set.

FAX initial setting

5-8

Call arrival

Distinctive ring (DRD 
setting)

Setting to determine whether or not to execute FAX arrival call by the distinctive 
ring.
Even if a call signal other than the set pattern is detected, there will be no 
automatic arrival call.
"0000": OFF
"0001": STANDARD
"1000": Pattern 1
"0100": Pattern 2
"1100": Pattern 3
"0010": Pattern 4
"1010": Pattern 5
"0110": ON (Australia)
"1110": ON (New Zealand)
"1001": ON (Hong Kong)
When contents other than the above are set, the initial value is reverted to.

FAX initial setting/
Setting

102

1

Not used

2-5

Call arrival

Setting of the number 
of automatic reception 
calls

Set the number of call sounds until the start of receiving (holding of the line) 
when automatic reception is set.
This can be set from 0 to 15 (Europe/Indonesia/Thailand: 0 to 9, Australia/New 
Zealand: 2 to 4) times by binary inputting.
If 0 is set, the call sound will not be sounded. (However, this does not include 
the nighttime FAX mode.)

FAX reception 
setting/
Setting

6

Call arrival

Setting for changing 
over to automatic 
reception during 
manual reception

Setting to determine whether or not to initiate automatic reception after the 
ringer sounds a certain number of times when manual reception is set.
"0": Prohibited (do not changeover)
"1": Permitted (changeover)

FAX reception 
setting/
Setting

7, 8

Not used

103

1-5

Call arrival

Setting of the number 
of calls for changing 
over from manual to 
automatic reception

Set the number of calls before changing over to automatic reception when in 
the manual reception mode.
Functions only in France.
This functions when the "Setting for changing over to automatic reception 
during manual reception" (SW71-6) is valid.
Setting can be made over the range of 1 to 9 times in 1 time increments by 
binary inputting.
The initial value is reverted to if a value outside of the setting range is set.

FAX reception 
setting/
Setting

6

Communication

ECM (valid except 
during V.34: reflected 
in the V.21 DIS/DCS/
DTC)

Setting to determine whether or not to execute the error re-send mode.
However, this is only valid when communication is other than V.34.
"0": Yes. Set with ECM function.
"1": No. Set with no ECM function.
ECM is on during communication in the V.34 mode.

FAX initial setting

7

Function

Change from the 
image send screen to 
the copy screen

Setting to determine whether or not to automatically change from the image 
send screen to the copy screen.
When changing over, if no keys are operated for 20 seconds after pushing the 
final key in the image send mode, the copy mode will be automatically switched 
to.
If there is no changeover, the machine will remain in the image send mode and 
not switch to the copy mode.
"0": Do not change over
"1": Change over
*3

Operation setting

8

Function

Image quality setting 
when saving (FAX)

Setting to determine whether or not to make filed image quality valid (initial 
setting for image quality selection when transmitting filed document files by 
FAX)
"0": Do not apply
"1": Apply

Operation setting

MX-FX15  FAX SOFTWARE SWITCH  2 – 18

104

1-4

Function

Image quality priority 
selection (standard 
image quality setting)

Setting to determine the initial setting for image quality selection when reading 
documents on the FAX.
"0000": Ordinary lettering
"0001": Small lettering
"0010": Fine
"0011": Very fine
"0101": Small lettering, medium tone
"0110": Fine, medium tone
"0111": Very fine, medium tone
"Ordinary lettering" (initial value) is reverted to if a value outside of the setting 
range is set.

Operation setting

5

Function

Received data printing 
hold (FAX/Internet 
FAX) 

Setting to determine whether or not to store data received by FAX/Internet FAX 
in the memory without outputting it.
"0": Do not hold
"1": Hold

Operation setting

6

Function

Saving the setting 
contents for a certain 
period after completion 
of scanning

Setting to determine whether the set values of the destination and various 
functions are saved without returning to the default values or not when 
reservation is completed on the image send screen.
"0": The set values are not saved.
"1": The set values are saved.

Operation setting

7

Reception Indicator 
Setting

Setting to determine whether or not the FAX reception lamp should be turned 
ON regardless of Energy Save mode (Power switch of controller is ON) or the 
normal mode if FAX/I-FAX received data is in the memory (not output) or FAX/I-
FAX received data is output to the right delivery tray.
Fax reception lamp is not ON in 1W (Nighttime FAX mode) as before.
“0”: Reception lamp Disable
“1”: Reception lamp Enable

8

Function

Default finish stamp 
setting

Setting to determine whether the finish stamp is used or not after completion of 
document scan when the document feed unit is used.
"0": NO (The finish stamp is not used.)
"1": YES (The finish stamp is used.)

Operation setting

105

1-4

Function

Speaker volume when 
on-hook (Speaker 
volume during DTMF 
sending)

This sets speaker volume for when the on-hook button is pushed.
The sound volume is set with a value. The greater the value is, the greater the 
sound volume is.
Setting range is 1 (small) to 15 (large) by binary input.
When it is set to "0," it is considered as setting to the default.

FAX initial setting

5-8

Function

Call sound volume

Irrespective of whether there is a handset, this sets the volume of the call 
sound that is sounded when a signal arrives.
The sound volume is set with a value. The greater the value is, the greater the 
sound volume is.
Setting range is 1 (small) to 15 (large) by binary input.
When it is set to "0," there is no sound (OFF).

FAX initial setting

106

1-4

Function

Line monitor volume 
setting

Set the speaker volume during line monitoring.
The sound volume is set with a value. The greater the value is, the greater the 
sound volume is.
Setting range is 1 (small) to 15 (large) by binary input.
When it is set to "0," there is no sound (OFF).

FAX initial setting

5-8

Function

Volume of the 
transmission 
completion sound 
(Volume of the 
successful 
transmission sound)

Set the volume of the completion sound outputted from the speaker upon 
completion of FAX transmission.
When sending is succeeded, a sound is generated by this setting.
The sound volume is set with a value. The greater the value is, the greater the 
sound volume is.
Setting range is 1 (small) to 15 (large) by binary input.
When it is set to "0," there is no sound (OFF).

FAX initial setting

107

1-4

Function

Volume of the 
communication error 
completion sound 
(Volume of the 
transmission and 
reception error sound)

This sets the volume of the completion sound outputted from the speaker upon 
completion of FAX communication error.
The sound volume is set with a value. The greater the value is, the greater the 
sound volume is.
Setting range is 1 (small) to 15 (large) by binary input.
When it is set to "0," there is no sound (OFF).

FAX initial setting

5-8

Function

Volume of the 
reception completion 
sound (Volume of the 
reception completion 
sound)

This sets the volume of the completion sound outputted from the speaker upon 
completion of FAX reception.
When receiving is succeeded, a sound is generated by this setting. 
The sound volume is set with a value. The greater the value is, the greater the 
sound volume is.
Setting range is 1 (small) to 15 (large) by binary input.
When it is set to "0," there is no sound (OFF).

FAX initial setting

: ‘16/Sep.

MX-FX15  FAX SOFTWARE SWITCH  2 – 19

108

1, 2

Function

Tone of the successful 
transmission sound

This sets the tone sounded when transmission is successful.
"00": Pattern 1 (550Hz)
"01": Pattern 2 (750Hz)
"10": Pattern 3 (1000Hz)
"11": Pattern 4 (1700Hz)

FAX initial setting

3, 4

Function

Tone of the 
transmission and 
reception error sound

This sets the tone sounded when there is a transmission and reception error.
"00": Pattern 1 (550Hz)
"01": Pattern 2 (750Hz)
"10": Pattern 3 (1000Hz)
"11": Pattern 4 (1700Hz)

FAX initial setting

5, 6

Function

Tone of the reception 
sound

This sets the tone sounded upon completion of reception.
"00": Pattern 1 (550Hz)
"01": Pattern 2 (750Hz)
"10": Pattern 3 (1000Hz)
"11": Pattern 4 (1700Hz)

FAX initial setting

7

Function

Auto startup mode

In the case where FAX or Internet FAX is received during nighttime mode or 
simulated mode, if this setting is ON, the received document will be outputted 
when the machine becomes able to output. When OFF, the machine will 
receive the data by proxy without outputting the document, but it will output the 
received document when the panel power SW is ON.
"0": Setting (setting for automatically starting up the main unit and outputting)
"1": Release (setting for storing in the memory without starting up the main unit)

FAX initial setting

8

Function

Digital line net setting

When this is set to "1: ON", "-15dBm" is set regardless of the soft switch setting 
in the signal send level on the FAXBOX side.
For MX-2310 series, the operation is made when this switch is set to ON.

FAX initial setting

109

1-3

Function

Setting of the 
successful 
transmission sound 
time

This sets the time the tone is sounded when transmission is successful.
"000": 2.0 seconds
"001": 2.5 seconds
"010": 3.0 seconds
"011": 3.5 seconds
"100": 4.0 seconds
The initial value is reverted to if a value outside of the setting range is set.

FAX initial setting

4-6

Function

Setting of the reception 
sound time

This sets the time the tone is sounded upon completion of reception.
"000": 2.0 seconds
"001": 2.5 seconds
"010": 3.0 seconds
"011": 3.5 seconds
"100": 4.0 seconds
The initial value is reverted to if a value outside of the setting range is set.

FAX initial setting

7

Function

Setting of the time of 
the transmission/
reception error sound

Transmission error sound sounding interval
"0": Every 0.3 seconds
"1": Every 0.7 seconds
Sounding time and paper feeding time are the same.

FAX initial setting

8

Not used

110

1, 2

Print

Communication results 
sheet print settings (for 
ordinary transmission)
<FAX only>

This sets outputting of the communication results sheet following transmission 
(excluding successive broadcast, successive polling and relay broadcast 
transmission).
"00": Do not print
"01": Always print
"10": At times of transmission failure
The initial value is reverted to if a value outside of the setting range is set.

FAX initial setting

3, 4

Print

Setting of the 
communication results 
sheet printing (at times 
of broadcast 
transmission)

This sets outputting of the communication results sheet at times of successive 
broadcast, successive polling and relay broadcast transmission.
"00": Do not print
"01": Always print
"10": Failed transmission address
The initial value is reverted to if a value outside of the setting range is set.

FAX initial setting

5, 6

Print

Communication results 
sheet print setting 
(when receiving)
<FAX only>

This sets outputting of the communication results sheet for when 
communications are received (excluding confidential communications).
"00": Do not print
"01": Always print
"10": At times of error
The initial value is reverted to if a value outside of the setting range is set.

FAX initial setting

7

Print

Report output (when 
receiving confidential 
communications)
<FAX only>

Setting to determine whether or not to output the communication results sheet 
(receiving) when confidential communications are received.
"0": Print
"1": Do not print
This only functions when the communication results sheet print setting 
(receiving) is set to be outputted.

FAX initial setting

8

Not used

MX-FX15  FAX SOFTWARE SWITCH  2 – 20

111

1, 2

Print

Print document 
contents when 
transmitting (results 
sheet)
<FAX only>

Setting to determine whether or not to print part of the transmitted document on 
the communication results sheet (transmission) when FAX transmission error 
occurs.
"00": Do not print
"01": Always print
"10": At times of error
The initial value is reverted to if a value outside of the setting range is set.
This functions when the communication results sheet print setting (ordinary 
transmission) (broadcast transmission) is set to be outputted.

FAX initial setting

3

Print

Automatic printing of 
the record sheet when 
memory is full.

Setting to determine whether or not to automatically output the communication 
record sheet when transmitted and received data on the FAX/Internet FAX 
communication record sheet reach 200 entries.
"0": No (do not output)
"1": Yes (automatically output)
If the data are not outputted, then new data are written over the previous data 
starting from the oldest of the 200 entries.
Trigger printing of 200 entries.

FAX initial setting

4-8

Print

Printing of the 
communication record 
sheet at a designated 
time (hours)

Set the hours part of the designated time (hours and minutes) for outputting the 
communication record sheet.
Setting can be made over the range of 0 to 23 (hours) in 1-hour increments by 
binary inputting. The initial value of 0 hour is reverted to if a value outside of the 
setting range is set.

FAX initial setting

112

1-6

Print

Printing of the 
communication record 
sheet at a designated 
time (minutes)

Set the minutes part of the designated time (hours and minutes) for outputting 
the communication record sheet.
Setting can be made over the range of 0 to 59 (minutes) in 1-minute increments 
by binary inputting. The initial value of 0 minute is reverted to if a value outside 
of the setting range is set.

FAX initial setting

7

Print

Printing of the 
communication record 
sheet at a designated 
time

Setting to determine whether or not to output the communication record sheet 
at a designated time.
"1": Output the communication record sheet at a designated time
"0": Do not output the communication record sheet at a designated time. Even if 
designated time printing is set, do not output when the designated time 
coincides with the nighttime FAX mode.

FAX initial setting

8

Not used

113

1-8

Reception

Remote changeover 
number setting

Set by binary inputting the number for receiving remote changeover from 
external telephones.
However, the remote changeover number is "XX*" with * fixed.
Adopt * when "A" is inputted.
Adopt # when "B" is inputted.
For bits 1-4, fix the upper digit of the remote changeover number. (0-F)
For bits 5-8, fix the second lowest digit of the remote changeover number. (0-F)
When C-F are set, the initial value is reverted to.

FAX initial setting

114

1, 2

Not used

3

Call arrival

FAX destination check 
function

Function to check the FAX destination in order not to send a FAX to an 
erroneous destination caused by operation mistake, etc.
"0": Disable
"1": Enable

FAX initial setting

4-7

Not used

8

Communication

External telephone 
connection

Setting to determine whether or not to use an external telephone.
If "Yes" is not set using this switch, an external telephone cannot be used.
"0": No (invalid)
"1": Yes (valid)
The user cannot set without an external telephone.

FAX initial setting

115

1-7

Not used

8

Transmission

Sender's name adding 
function

Setting is made whether the sender's number in the sender print is changed to 
the receiver's name or not.
When it is set to the receiver's name, if the address is set by  the one-touch key, 
the key name of the address is printed in the sender print section.
If it is not by the one-touch key (including automatic reversing with interface), 
print is not made (blank). 
"0": Sender's number (Default)
"1" :Receiver's name
* This function is valid only in the special ROM (made in August, 2009).

The format of the added receiver's name is ">>Receiver's name (one-touch 
key name)."

FAX initial setting