DOWNLOAD Sharp MX-FWX1 Service Manual ↓ Size: 43.31 MB | Pages: 127 in PDF or view online for FREE

MX-7040N  MX-RB14 (PAPER PASS UNIT)  7 – 5

1)

Install the step screw (Packed items No.14).

2)

Hang the spring (Packed items No. 17).

3)

Slide the upper door stopper R (Packed items No. 5) in the
arrow direction and attach it.

4)

Hang the spring on the upper door stopper R.

5)

Install the washer large (Packed items No.15), washer small
(Packed items No.16) and screw (Packed items No.12).

Attach the upper door to the paper pass unit.

MX-7040N  MX-LC13 (LARGE CAPACITY TRAYS)  8 – 1

MX-7040N

Service Manual

 

NOTE: Before installing MX-LC13, the installation of MX-RB14 is

needed.

1)

Remove the machine from the palette with a forklift or a slope
(DKIT-0367FCZZ).

NOTE: When using a forklift, raise the casters to the top in

order not to break them.

*1: Not used in this model.

NOTE: Before installation, be sure to turn both the operation and

main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.

1)

Draw out the second tray from the unit.
Push the button of the bottom side of the unit to unlock the
tray, and then slowly pull out the tray until it stops.

2)

Remove 3 screws from the tray.

3)

Slowly insert the tray to the original position.

1

LCT connecting plate F

1

2

LCT connecting plate R

1

3

Height adjustment plate

4

4

Screw (S-tight, M4 x 8)

11

5

Power cable

1

6

Connecting plate upper

2

7

Positioning plate F

1

8

Positioning plate R

1

9

Connecting plate lower F

1

10

Connecting plate lower R

1

11

Screw (Hex washer S-tight M4 x 18)

4

12

L-shape driver 

*1

1

4

3

2

5

1

6

7

11

12

8

10

9

MX-7040N  MX-LC13 (LARGE CAPACITY TRAYS)  8 – 2

1)

Attach the LCT connecting plate to the large capacity trays
with the screws (Packed items No.4 S-tight, M4 x 8).

MEMO: The reference label is attached to the plate. Attach it
so that the label can be seen from the outside.

2)

Attach the connection plates lower F/R to the relay unit with
the screws (Packed items No.11 Hex washer S-tight M4 x 18).

3)

Fix the upper mounting plates to the machine with the screws
(Packed items No. 4 S-tight, M4 x 8).

4)

Insert the installation plate of the LCT to the mounting plate of
the paper pass unit.

5)

Open the front door of LCT and remove the screw and remove
the lower cabinet.

6)

Underlay the adjustment bolt with the adjuster.

1

MX-7040N  MX-LC13 (LARGE CAPACITY TRAYS)  8 – 3

7)

Screw the adjustment bolt to adjust the height of LCT.

Check if the adjustment mark is on this position like the illustra-
tion above.
If not, perform this adjustment until it's OK.

8)

Fix the positioning plate and with the screw (Packed items
No.4 S-tight, M4 x 8).

9)

Open the front cabinet and fix the lower cabinet with the screw.

When separating, tighten the screw to release the
lock. 

When connecting again, loosen the screw after con-
nection.

1)

Remove the cover of LCT.

2)

Cut the rear cabinet with using nipper or cutter to make a hole,
and then wire the harness through the hole.

1