DOWNLOAD Sharp MX-FWX1 Service Manual ↓ Size: 43.31 MB | Pages: 127 in PDF or view online for FREE

MX-7040N  MX-LCX3N (LARGE CAPACITY TRAY)  5 – 9

2)

Push the large capacity tray into the closed (locked) position.

Then make a copy again to check to insure that there is no
shift. Repeat this procedure as required.

b. When shifted to the rear side
When shifting the line of printing from the center of the paper in the
B direction of arrow as shown below:
1)

Loosen the blue off-center adjustment screws (each 2 pcs.),
and move the side plate by the dimension shifted in the direc-
tion B (F side), and tighten the blue screws.

NOTE: Move the side plates by the same dimension on the

front side and the rear side.

2)

Push the large capacity tray into the closed (locked) position.

Then make a copy again to insure that there is no shift. Repeat
this procedure as required.

Since the regulation plates are adjusted when shipping, there is
basically no need to readjust. If, however, there is skew, adjust the
regulation plate width and the diagonal feed in the following proce-
dures:

a. Regulation plate width adjustment
1)

Press the lock button on the front cabinet and lower the paper
feed base tray to the paper supply position. Pull out the large
capacity tray.

MX-7040N  MX-LCX3N (LARGE CAPACITY TRAY)  5 – 10

2)

Set a sheet of paper on the paper feed base tray. Check that
the front regulation plate is at the marked center, and push it in
contact with the front regulation plate. Loosen the blue screws
of the rear regulation plate.

3)

Use the mark of the rear regulation plate, and fix the blue
screws at the position so that the clearance between paper
and the rear regulation plate is evenly 1mm.

NOTE: The positions of the regulation plates are even to the

right and left marks.

b. Diagonal feed adjustment
1)

Press the lock button on the front cabinet and lower the paper
feed base tray to the paper supply position. Pull out the tray.

2)

Adjust the diagonal feed.

In the case of diagonal feed 1
Loosen the blue screw (A) on the front regulation plate.
Referring to the degree of diagonal feed, move the regulation
plate in the direction of (-) and fix the blue screw.

1mm

Diagonal feed 1

Transport

direction

Diagonal feed 2

MX-7040N  MX-LCX3N (LARGE CAPACITY TRAY)  5 – 11

In the case of diagonal feed 2
Loosen the blue screw (A) on the front regulation plate.
Referring to the degree of diagonal feed, move the regulation
plate in the direction of (+) and fix the blue screw.

3)

Set a sheet of paper on the paper feed base tray and adjust
the regulation plate width. (Refer to "a. Regulation plate width
adjustment.")

NOTE: After completion of the adjustment, check that the front

and rear regulation plates are parallel to each other.

MX-7040N  MX-MF10 (MULTI BYPASS TRAY)  6 – 1

MX-7040N

Service Manual

 

NOTE: Before installation, be sure to turn both the operation and

main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.

1)

Remove the screw, and remove the front cabinet lower of the
right door.

2)

Remove the screw, and remove the rear cabinet of the right
door.

1)

Insert the manual paper feed unit into the machine, and fix it
with the screws (4 pcs.).

2)

Connect the harness.

1)

Attach the rear cabinet of the right door and the front cabinet
lower of the right door to the original positions.

1

Multi bypass UN

1

2

ADU cabinet F lower

1

3

ADU cabinet R lower

1

4

Screw S-tight M4 x 8

5

5

Screw P-tight M4 x 10

3

2

1

4

5

3