Sharp MX-B200 (serv.man8) User Manual / Operation Manual ▷ View online
7
65
CHECKING THE TONER LEVEL
The toner level is indicated by a 6-level display. Use it as a guideline for replacing
the toner cartridge.
the toner cartridge.
1
Hold down the light (
) key until the alarm indicators (
,
,
, )
blink.
The display will show "- -".
2
Hold down the Copy ratio display (%) key for more than 5
seconds.
seconds.
The approximate quantity of toner remaining
will be indicated in the display as a percentage.
("100", "75", "50", "25", "10" is displayed.)
When the percentage is less than 10%, "LO"
will be displayed.
will be indicated in the display as a percentage.
("100", "75", "50", "25", "10" is displayed.)
When the percentage is less than 10%, "LO"
will be displayed.
3
Press the light (
) key to return to the normal display.
The alarm indicators (
,
,
,
) go off.
The display returns to the number of copies display.
8
8
66
This chapter describes how to replace the toner cartridge and how to clean the unit.
TONER CARTRIDGE REPLACEMENT
When the toner cartridge replacement required (
) indicator lights up, replacement
of the toner cartridge will be needed soon. Obtain a new cartridge. When the toner
cartridge replacement required (
cartridge replacement required (
) indicator blinks, the toner cartridge must be
replaced before copying can be resumed. Replace the toner cartridge by following
the procedure below.
the procedure below.
1
Open the multi-bypass tray,
and then open the side
cover while pressing the
side cover open button.
and then open the side
cover while pressing the
side cover open button.
2
Push gently on both sides of the
front cover to open the cover.
front cover to open the cover.
Be sure to use only genuine SHARP parts and supplies.
• After the unit stops, it may be possible to make a few more copies by
taking the toner cartridge out of the unit, shaking it horizontally, then
reinstalling it. If copying is not possible after this operation, replace the
toner cartridge.
reinstalling it. If copying is not possible after this operation, replace the
toner cartridge.
• During long copy run of a dark original, the start (
) indicator may
blink, the indicator light up, and the unit stop, even though toner is left.
The unit will feed toner up to 2 minutes and then the start (
The unit will feed toner up to 2 minutes and then the start (
)
indicator will light up. Press the start (
) key to restart copying.
MAINTENANCE
8
67
3
Gently pull the toner cartridge out
while pressing the lock release
button.
while pressing the lock release
button.
4
Remove the toner cartridge from the bag. Grasp the cartridge
on both sides and shake it horizontally four or five times. After
shaking the cartridge, remove the toner seal.
on both sides and shake it horizontally four or five times. After
shaking the cartridge, remove the toner seal.
5
Gently insert the toner cartridge
along the guides until it locks in
place while pushing the lock
release lever. Remove the tape
from the shutter. Pull the shutter
out of the toner cartridge as
shown in the illustration.
Discard the shutter.
along the guides until it locks in
place while pushing the lock
release lever. Remove the tape
from the shutter. Pull the shutter
out of the toner cartridge as
shown in the illustration.
Discard the shutter.
• After removing the toner cartridge, do not shake it or tap on it. Doing
so may cause toner to leak from the cartridge. Put the old cartridge
immediately in the bag contained in the box of the new cartridge.
immediately in the bag contained in the box of the new cartridge.
• Dispose of the old toner cartridge in accordance with local regulations.
Grasp the toner cartridge as shown in the illustration. Do not hold the
cartridge by the shutter. Be sure to only shake the cartridge before the
toner seal is removed.
cartridge by the shutter. Be sure to only shake the cartridge before the
toner seal is removed.
Lock release button
4 or 5 times
Shutter
Toner seal
8
68
6
Close the front cover and then
the side cover by pressing the
round projections near the
side cover open button. The
indicator will go out and the
start (
the side cover by pressing the
round projections near the
side cover open button. The
indicator will go out and the
start (
) indicator will light
up.
When closing the covers, be
sure to close the front cover
securely and then close the
side cover. If the covers are
closed in the wrong order, the
covers may be damaged.
sure to close the front cover
securely and then close the
side cover. If the covers are
closed in the wrong order, the
covers may be damaged.
Even after a new toner cartridge is installed, the start (
) indicator
may not light up, indicating copying cannot be restarted (toner is not
sufficiently fed). In this case, open and close the side cover. The copier
will feed toner again approximately 2 minutes and then copying can be
restarted.
sufficiently fed). In this case, open and close the side cover. The copier
will feed toner again approximately 2 minutes and then copying can be
restarted.
Click on the first or last page to see other MX-B200 (serv.man8) service manuals if exist.