Sharp MX-B200 (serv.man8) User Manual / Operation Manual ▷ View online
7
7
61
This chapter describes the special functions of this unit. Use these functions as
needed.
needed.
DESCRIPTION OF SPECIAL FUNCTIONS
Toner save mode
Reduces toner consumption by approximately 10%.
Power save modes
The unit has two power save modes of operation: preheat mode and auto power
shut-off mode.
shut-off mode.
Preheat mode
When the unit enters the preheat mode, the power save (
) indicator will light up
and other indicators will remain on or off as before. In this condition, the fuser in
the unit is maintained at a lower heat level, thereby saving power. To copy from
the preheat mode, make desired copier selections and press the start (
the unit is maintained at a lower heat level, thereby saving power. To copy from
the preheat mode, make desired copier selections and press the start (
) key
using the normal copying procedure.
Auto power shut-off mode
When the unit enters the auto power shut-off mode, the power save (
) indicator
will light up and other indicators will go out. The auto power shut-off mode saves
more power than the preheat mode but requires a longer time before starting
copying. To copy from the auto power shut-off mode, press the start (
more power than the preheat mode but requires a longer time before starting
copying. To copy from the auto power shut-off mode, press the start (
) key.
Then make desired copier selections and press the start (
) key using the
normal copying procedure.
Auto clear
The unit returns to the initial settings a preset amount of time after the end of job.
This preset amount of time (auto clear time) can be changed.
This preset amount of time (auto clear time) can be changed.
Resolution of AUTO & MANUAL mode
You can set the copy resolution used for AUTO and MANUAL (
) exposure
mode.
SPECIAL FUNCTIONS
7
62
Check original cover/SPF open function
When enabled, this function may help prevent wasteful use of toner that occurs
when the original cover/SPF is not completely closed.
If the start (
when the original cover/SPF is not completely closed.
If the start (
) key is pressed when the original cover/SPF is not completely closed,
"
" will appear in the display and copying may not take place. If copying does not
take place, copying can be performed by pressing the start (
) key again, however,
the scan size set in "Copy effective paper width setting function" (program numbers
25, 26, 27) will be used.
If the original cover/SPF is completely closed after "
25, 26, 27) will be used.
If the original cover/SPF is completely closed after "
" appears, copying will take
place at the normal size.
TONER SAVE MODE
1
Press the exposure mode selector key
to select the MANUAL (
to select the MANUAL (
) mode.
2
Press and hold down the exposure mode
selector key for approximately 5 seconds.
The MANUAL (
selector key for approximately 5 seconds.
The MANUAL (
) indicator will go out
and the PHOTO (
) indicator will begin
to blink. The light and dark indicator
marked "5" will light up, indicating the
standard toner mode is active.
marked "5" will light up, indicating the
standard toner mode is active.
3
To enter the toner save mode, press the
light (
light (
) key. The light and dark
indicator marked "1" will light up,
indicating the toner save mode is
selected.
indicating the toner save mode is
selected.
4
Press the exposure mode selector key. The PHOTO (
) indicator
will stop blinking and light up steadily. The light and dark indicator
marked "3" will light up. The toner save mode is now active.
marked "3" will light up. The toner save mode is now active.
When this function is off, if the start (
) key is pressed to make a copy with
the original/SPF cover open, parts outside of the original will be copied black.
Even when this function is on, if the start (
Even when this function is on, if the start (
) key is pressed twice to make a
copy with the original/SPF cover open, parts outside the original may be
copied black. To prevent excessive use of toner, make sure that the original/
SPF cover is closed when making a copy.
copied black. To prevent excessive use of toner, make sure that the original/
SPF cover is closed when making a copy.
To return to the standard mode, repeat the procedure but use the dark
(
(
) key to select exposure level "5" in step 3.
7
63
USER PROGRAMS
The user programs allow the parameters of certain functions to be set, changed, or
cancelled as desired.
cancelled as desired.
Setting the user programs
1
Press and hold down the light (
) key for more than 5
seconds until all the alarm indicators (
,
,
,
) blink and
"
" appears in the display.
2
Use the left copy quantity (
) key to select a user program
number (For the user program numbers, see the following table.).
The selected number will blink in the left side of the display.
The selected number will blink in the left side of the display.
3
Press the start (
) key. The entered program number will be
steadily lit and the currently selected parameter number for the
program will blink on the right side of the display.
program will blink on the right side of the display.
4
Select the desired parameter using the right copy quantity (
) key.
The entered parameter number will blink on the right of the display.
Program
No.
Mode
Parameters
1
Auto clear time
1
10 sec., 2
30 sec., *3
60 sec.,
4
90 sec., 5
120 sec., 6
OFF
2
Preheat mode
*1
30 sec., 2
60 sec., 3
5 min.,
4
30 min., 5
60 min., 6
120 min.,
7
240 min.
3
Auto power shut- off
mode
mode
*1
ON, 2
OFF
4
Auto power shut- off
timer
timer
*1
5 min., 2
30 min., 3
60 min.,
4
120 min., 5
240 min.
6
SPF automatic
original discharge
time (Only operates
when an SPF is
installed.)
original discharge
time (Only operates
when an SPF is
installed.)
1
5 min., *2
30 min.,
3
60 min., 4
120 min.,
5
240 min., 6
OFF
10
Resolution of AUTO
& MANUAL mode
& MANUAL mode
*1
300dpi, 2
600dpi
13
Memory for printer
1
30%, 2
40%, *3
50%,
4
60%, 5
70%
21
Reset factory
1
YES, *2
NO
22
Sort auto select
*1
ON, 2
OFF
24
Prevention of OC
copies when the
original cover/SPF
is up function
copies when the
original cover/SPF
is up function
*1
ON, 2
OFF
7
64
* Factory default settings are indicated with an asterisk (*).
5
Press the start (
) key. The right-hand number in the display
will be steadily lit and the entered value will be stored.
6
Press the light (
) key to return to the normal copy mode.
DISPLAYING TOTAL NUMBER OF COPIES
Use the following procedure to display the total number of copies.
Press and hold down the clear key for approximately 5 seconds. The
total number of copies will appear in two steps, each with three digits.
Example: Total number of copies is 1,234.
total number of copies will appear in two steps, each with three digits.
Example: Total number of copies is 1,234.
25
Copy effective paper
width setting function
(Bypass tray)
width setting function
(Bypass tray)
*1
Large (A4 width),
2
Small (B5R width)
26
Copy effective paper
width setting function
(Tray 1)
width setting function
(Tray 1)
*1
Large (A4 width),
2
Small (B5R width)
27
Copy effective paper
width setting function
(Tray 2)
(Only operates when
a lower paper tray is
installed.)
width setting function
(Tray 2)
(Only operates when
a lower paper tray is
installed.)
*1
Large (A4 width),
2
Small (B5R width)
28
Selection of copy
start state (Polygon
rotation on/off)
start state (Polygon
rotation on/off)
*1
ON, 2
OFF
29
Fusing temperature
setting when the
bypass tray is used
setting when the
bypass tray is used
1
Low, *2
High
32
USB 2.0 mode
switching
switching
1
Full-Speed, *2
Hi-Speed
To change the setting or to set another mode, press the clear
key. The unit will return to step 2.
key. The unit will return to step 2.
Program
No.
Mode
Parameters
Click on the first or last page to see other MX-B200 (serv.man8) service manuals if exist.